Command Descriptions - Icom IC-FR3000 Series Sales Handbook

3-6-4

1 1 1 1 - - - - 4 COMMAND DESCRIPTIONS

4 COMMAND DESCRIPTIONS
4 COMMAND DESCRIPTIONS 4 COMMAND DESCRIPTIONS
• System Control Exit • System Control Exit • System Control Exit • System Control Exit
Turns OFF "System Control standby mode" and
returns to normal operating mode. Will also "Hang
up" the phone line during Phone Patch operation.
• Repeat Start • Repeat Start
• Repeat Start • Repeat Start
This command enables repeater operation. This
command is not available during Phone Patch
operation.
• Repeat Stop • Repeat Stop
• Repeat Stop • Repeat Stop
This command inhibits repeater operation
immediately even while transmitting. May be
cancelled by entering "Repeat Start" command or
power the repeater OFF/ON. This command is not
available during Phone Patch operation.
• TX Start • TX Start • TX Start • TX Start
This command initiates repeater transmit mode for
Phone Patch operation. This command is available
only when the signal is entered via the connected
telephone line.
• TX Stop • TX Stop • TX Stop • TX Stop • TX Stop • TX Stop • TX Stop • TX Stop
This command stops the repeater from transmitting
during Phone Patch operation. This command is
available only when the signal is entered via the
connected telephone line.
• RF Power (Low) • RF Power (Low) • RF Power (Low) • RF Power (Low)
Switches TX power to "Low." This command is not
available during Phone Patch operation.
• RF Power (High) • RF Power (High)
• RF Power (High) • RF Power (High)
Switches TX power to "High." This command is not
available for the channel which low power is
programmed by cloning or during Phone Patch
operation.
• RX Unit OFF • RX Unit OFF • RX Unit OFF • RX Unit OFF
Turn OFF the RX unit (front end). This command is
not available from a transceiver or during Phone
Patch operation.
• RX Unit ON • RX Unit ON • RX Unit ON • RX Unit ON
Turn ON the RX unit (front end). This command is not
available from a transceiver or during Phone Patch
operation.
Command Descriptions
• TX/RX Unit OFF • TX/RX Unit OFF • TX/RX Unit OFF • TX/RX Unit OFF
• TX/RX Unit ON • TX/RX Unit ON
• TX/RX Unit ON • TX/RX Unit ON
• Master Enable • Master Enable
• Master Enable • Master Enable
• Slave Enable • Slave Enable • Slave Enable • Slave Enable
• TEL Dial • TEL Dial • TEL Dial • TEL Dial
• TEL Autodial • TEL Autodial • TEL Autodial • TEL Autodial
• Memory CH Select • Memory CH Select
• Memory CH Select • Memory CH Select
• CPU All Reset • CPU All Reset
• CPU All Reset • CPU All Reset
Turn OFF the TX/RX units. This command is not
available from a transceiver or during Phone Patch
operation.
Turn ON the TX/RX units. This command is not
available from a transceiver or during Phone Patch
operation.
Activates the master repeater when connected to a
back up repeater. This command is not available
during Phone Patch operation.
Activates the back up repeater when connected to a
master repeater. This command is not available
during Phone Patch operation.
Activates the phone line and dials the telephone
number entered as sub code (max. 24 digits).
Command will not activate when the first digit
entered is the same as programmed in "Call entered is the same as programmed in "Call
Prohibition." The repeater transmits "NG ACK" signal.
This command is only available from a transceiver.
Activates the phone line and dials the pre-
programmed autodial channel (2 digits) as sub code.
This command is only available from a transceiver.
Selects the memory channel with sub code (2 digits
Memory channel number). This command is not
available during Phone Patch operation.
Resets the repeater's CPU. This command is not
available from a transceiver or during Phone Patch
operation.
37