Related Manuals for Salus VS05
Summary of Contents for Salus VS05
- Page 1 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 1 Dial Thermostat Models: VS05 I N S TA L L E R / U S E R M A N U A L...
-
Page 2: Table Of Contents
VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 2 Contents Contents Icons used in this manual: For latest PDF installation Introduction. guide please go to Product Compliance. Safety www.salus-controls.com Safety information. Mounting position and Important info installation. -
Page 3: Product Compliance
VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 3 Product Compliance & Safety Information INTRODUCTION Safety Information Use in accordance with the regulations Thank you for purchasing the SALUS room The SALUS VS05 is to be used for room thermostat VS05. - Page 4 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 4 Product Compliance & Safety Information Sources of danger Installer parameter settings The thermostat must be disconnected from The SALUS VS05 is equipped with installer parameters. See page 13.
-
Page 5: Mounting Position And Installation
VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 5 Installation – Thermostat Mounting Mounting position and installation To ensure trouble free operation and efficient control, the unit is best positioned in a draft free area and at 130cm from the floor. Do not position the thermostat near any heat source, behind curtains, direct sunlight or an area of high humidity. -
Page 6: System Grouping And Communication
VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 6 System Overview Grouping and Communication Power and Switching Cable - used to power thermostats and drive output. Grouping and Communication cable. While the thermostats can function as standalone,... - Page 7 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 7 System Overview Grouping and Communication The maximum number of groups per KL10 wiring centre is two. The group selection communication cable must correspond to the group terminals on the KL10 WC.
- Page 8 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 8 Installation – Thermostat Mounting Gently remove front housing. Wall Mounting For wall mounting, mark and mount the rear case to the wall. The VS05 is suitable for wall boxes with a centre...
- Page 9 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 9 Installation – Terminal Connections Understanding your terminal connections Power Terminals 230 Vac Used for supplying power to the Rear of VS05 unit and switched output. Sensor Terminals Can be used for external Air or Floor sensor.
- Page 10 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 10 Installation – Thermostat Connections Optional communication connection 12VDC While the VS05 can function on its own, installing this optional, inexpensive communication cable allows the VS05 to communicate with the SALUS VS10 (sold separately).
- Page 11 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 11 Installation – Terminal Connections Check that the wiring is completed for: Power Terminals Sensor Terminals (if applicable) Communication Terminals (optional but recommended) You are ready to secure the rear housing to the wall box Please use the screws provided.
- Page 12 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 12 Installation If any parameter settings need to be changed please refer to next page. Fit the front housing to the rear housing as shown above. VS05 Installer Manual...
- Page 13 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 13 Installation – parameter setting External sensor (optional) If you are fitting an external sensor for air/floor sensing please select temp here. It can be set from 0-45ºC and is preset at 27ºC. Please note...
-
Page 14: User Interface
VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 14 User Interface LED Indication Temperature Adjustment 5-30 The VS05 is no longer a member of the group and will ignore commands from the VS10 group control thermostat. The VS05 is a group member and will follow commands Mode from the VS10 group control thermostat. - Page 15 For more details on VS10 please refer to VS10 manual If you do not want a VS05 to follow the group control thermostat VS10 please select see previous page. VS05 Installer Manual...
- Page 16 The group control thermostat will be in one of the following modes: For more details on VS10 please refer to VS10 manual If you do not want a VS05 to follow the group control thermostat VS10 please select see page 14. VS05 Installer Manual...
- Page 17 For more details on VS10 please refer to VS10 manual If you do not want a VS05 to follow the group control thermostat VS10 please select see page 14. VS05 Installer Manual...
- Page 18 To enter manual mode, slide the switch to the position. The thermostat will not follow the group control thermostat VS10 and will no longer be part of the group. The VS05 will work as a stand alone thermostat. RED Led indicates that power is going to the unit in normal operation.
- Page 19 To enter manual mode, slide the switch to the position. The thermostat will not follow the group control thermostat VS10 and will no longer be part of the group. The VS05 will be in permanent frost protection. Blue LED indicates the thermostat is in frost protection mode.
- Page 20 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 20 Technical Detail MODEL VS05 TYPE Wired dial thermostat designed for 230V AC heating/cooling applications TEMPERATURE Scale Celsius Tolerance 0.5 ºC Set Temperature range 5-30 ºC Frost Protection 5ºC...
- Page 21 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 21 Installer Notes VS05 Installer Manual...
- Page 22 VS05 Installer - User Manual 005_Layout 1 08.12.2014 13:32 Strona 22 Installer Notes VS05 Installer Manual...
- Page 23 SALUS Controls sole liability for breach of this warranty will be (at its option) to repair or replace the defective product.
-
Page 24: Www.salus-Controls.com
SALUS Controls is a member of the Computime Group Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change specification, design and materials of products listed in this brochure without prior notice. Issue Date: April 2014 For PDF Installation guide please go to www.salus-controls.com...