Salus VS10WRF Full User Manual
  1. Manuals
  2. Brands
  3. Salus Manuals
  4. Thermostat
  5. VS10WRF
  6. Full user manual

Salus VS10WRF Full User Manual

Hide thumbs Also See for VS10WRF:
Table of Contents

Advertisement

Quick Links

VS10WRF/VS10BRF THERMOSTAT - FULL USER MANUAL

Advertisement

Table of Contents
loading

Related Manuals for Salus VS10WRF

Summary of Contents for Salus VS10WRF

  • Page 1 VS10WRF/VS10BRF THERMOSTAT - FULL USER MANUAL...

  • Page 2: Table Of Contents

    4.2 Button description..................................9 4.3 First power up sequence, language choice and preparing to the pair process................10 5. Installation by SALUS Smart Home application (ONLINE MODE)..................11 5.1 General informations about SALUS Smart Home application....................... 11 5.2 Configuration as a programmable thermostat..........................12 5.2.1 Pairing with underfloor heating wiring centre (KL08RF/Control Box)................
  • Page 3 6.11 Error codes (exclamation mark in app)............................52 6.12 Wireless signal strength test..............................53 6.13 Factory reset (removing thermostat from the app and ZigBee network)................... 54 7. Installation in OFFLINE MODE without SALUS SmartHome application................56 7.1 General informations................................... 56 7.2 Configuration as a programmable thermostat..........................57 7.2.1 Pairing with underfloor heating wiring centre (KL08RF/Control Box)................

  • Page 5: Introduction

    1.3 Product Overview VS10WRF / VS10BRF is a room temperature thermostat that is used for wireless control of iT600 series devices such as: KL08RF wiring centre, TRV radiator valve and RX10RF boiler receiver. In combination with Universal Gateway UGE600 this regulator can be controlled over the Internet using SALUS SmartHome app (Online mode).

  • Page 6: Montage

    Mounting: to mount thermostat you can use accesories included with the set (mounting screws). Remove back cover to mount the plate to the wall. Now please insert the batteries inside the thermostat. After this just attach thermostat to the plate right into designed holes in the plate. 2.3 Connection Description (VS10WRF/VS10BRF thermostat) Symbols explanation: S –...

  • Page 7: About Zigbee Network

    3. About ZigBee network 3.1 ZigBee network - creation and work ZigBee is a wireless network based on IEEE 802.15.4 standard and it’s communication takes place in the 2.4 GHz band. The network is based on a mesh topology, which allows for a very large range and high reliability. The maximum range of direct communication between two network nodes (devices) is about 100m in open space.

  • Page 8: Compatibility With Salus Devices (Online And Offline)

    3.2 Compatibility with SALUS devices (ONLINE AND OFFLINE) COMPATIBILTY WITH OTHER SALUS CONTROLS DEVICES ONLINE MODE OFFLINE MODE Universal Gateway is NOT Universal Gateway is CONNECTED TO THE INTERNET CONNECTED TO THE INTERNET You can use your devices locally You can configure and use all your without the SmartHome App.

  • Page 9: Before You Start (First Power Up)

    4. Before you start (first power up) 4.1 LCD icon description 1. Comfort temperature 13. AM / PM 2. Standard temperature 14. Lock function 3. Economic temperature 15. Clock 4. Automatic mode 16. Day indicator 5. PARTY mode 17. Settings 6.

  • Page 10: First Power Up Sequence, Language Choice And Preparing To The Pair Process

    4.3 First power up sequence, language choice and preparing to the pair process Remove the protection foil and insert ...it will display all icons... After that, thermostat will automatically power 4xAAA batteries by removing back cover. up and start boot sequence..then thermostat will display the Set your thermostat for underfloor software version.

  • Page 11: Installation By Salus Smart Home Application (Online Mode)

    5.1 General informations about SALUS Smart Home application Thanks to UGE600 Universal Gateway and SALUS Smart Home app system allows you to remote control of your heating system in any place you are in the moment by smartphone, tablet or computer with Internet connection. Then you have also access to advanced functions of VS10WRF/VS10BRF thermostat.

  • Page 12: Configuration As A Programmable Thermostat

    SALUS SmartHome Set your thermostat for underfloor heating Now thermostat is looking for the Go to SALUS Smart Home app. by „ ” or „ ” buttons. Then signal from the coordinator...
  • Page 13 Thermostat is connected. Go to the Select your thermostat and press Name your thermostat and go Smart Home app to configure it. „Connect equipment” button. „Next”... Select option „Programmable Now choose Press gear icon. Thermostat”. „UFH Wiring Centre” option.
  • Page 14 After that thermostat will display Gateway stop flashing and turn to steady Press „Finish” button to end the set main screen. blue color which means pair process has up process in the app. You succesfully configured been finished. VS10WRF/VS10BRF thermostat with KL08RF Control Box.

  • Page 15: Pairing With Wireless Trv Radiator Head

    For easier installation, please make sure you have already added wireless TRV radiator heads to your ZigBee network (please refer to the wireless TRV radiator head manual instruction). SALUS SmartHome Set your thermostat for radiators by Go to SALUS Smart Home app. Now thermostat is looking for the „ ” or „ ” buttons.
  • Page 16 After that thermostat will display main screen. Choose „No” if you want to set your own Press „Finish” button to end the set You succesfully configured VS10WRF/VS10BRF schedule later or „Yes” if default now. up process in the app. thermostat with Wireless TRV radiator head.

  • Page 17: Pairing With Smart Plug Spe600

    For easier installation, please make sure you have already added Smart Plug SPE600 to your ZigBee network (please refer to the Smart Plug SPE600 manual instruction). SALUS SmartHome Set your thermostat for underfloor heating Now thermostat is looking for the Go to SALUS Smart Home app. by „ ” or „ ” buttons. Then signal from the coordinator... confirm by button.
  • Page 18 After that thermostat will display main screen. Choose „No” if you want to set your own Press „Finish” button to end the set You succesfully configured VS10WRF/VS10BRF schedule later or „Yes” if default now. up process in the app. thermostat with Smart Plug SPE600.

  • Page 19: Pairing With Smart Relay Sr600

    For easier installation, please make sure you have already added Smart Relay SR600 to your ZigBee network (please refer to the Smart Relay SR600 manual instruction). SALUS SmartHome Set your thermostat for underfloor heating Now thermostat is looking for the Go to SALUS Smart Home app. by „ ” or „ ” buttons. Then signal from the coordinator... confirm by button.
  • Page 20 After that thermostat will display main screen. Choose „No” if you want to set your own Press „Finish” button to end the set You succesfully configured VS10WRF/VS10BRF schedule later or „Yes” if default now. up process in the app. thermostat with Smart Relay SR600.

  • Page 21: Pairing With Rx10Rf Receiver

    For easier installation, please make sure you have already added RX10RF receiver to your ZigBee network (please refer to the RX10RF receiver manual instruction). SALUS SmartHome Set your thermostat for underfloor heating Go to SALUS Smart Home app Now thermostat is looking for the by „ ” or „ ” buttons. Confirm signal from the coordinator...
  • Page 22 After that thermostat will display main screen. Choose „No” if you want to set your own Press „Finish” button to end the set You succesfully configured VS10WRF/VS10BRF schedule later or „Yes” if default now. up process in the app. thermostat with RX10RF receiver.

  • Page 23: Configuration As A Hot Water Timer

    For easier installation, please make sure you have already added other devices to your ZigBee network, such as Underfloor Heating Control Box (KL08RF) or RX10RF. SALUS SmartHome Set your thermostat for underfloor heating Now thermostat is looking for the Go to SALUS Smart Home app. signal from the coordinator... by „ ” or „ ” buttons. Confirm button.
  • Page 24 After that thermostat will display main screen. Choose Room Extension Receiver. Press „Finish” button to end the set You succesfully configured VS10WRF/VS10BRF up process in the app. thermostat as a hot water timer with RX10RF receiver.

  • Page 25: Operating In Online Mode (By App)

    6.1 General informations This section will show how to use your VS10WRF/VS10BRF thermostat with the UGE600 Universal Gateway and the Salus Smart Home App. In order to do that, you will need a Salus UG600/UGE600 Universal Gateway, the Salus Smart Home App and Internet connection. Controlling your thermostat via the App gives you a lot of freedom and the possibilities to manage the temperature in your house/office remotely (Smart Home app is available for Android/iOS mobile devices or Internet browser).

  • Page 26: Hot Water Timer

    6.2.2 Hot Water Timer Menu view of VS10WRF/VS10BRF thermostat set as a Hot Water Timer in SALUS SmartHome application: Thermostat name Thermostat name change tool Hot Water Timer work mode selection tool. - Turned ON - AUTO mode (schedule) - Turned OFF...

  • Page 27: Change Thermostat Name (Pencil Icon)

    6.3 Change thermostat name (pencil icon) Select the thermostat in Press the thermostat’s name. the main app menu. Click on the pencil icon. Name your termostat and confirm it by „Save” button.

  • Page 28: Work As A Programmable Thermostat

    6.4 Work as a programmable thermostat 6.4.1 Setpoint temperature change You can change the setpoint by sliding the cursor to left/right on your App. On your App screen, the setpoint temperature is the number displayed in a larger font. Select the thermostat in Old setpoint value.

  • Page 29: Heat/Cool Mode Change (Kl08Rf Connection)

    6.4.2 Heat/Cool mode change (KL08RF connection) VS10WRF/VS10BRF thermostat could be a heating device or cooling device. Default thermostat is set for heating. To set cool mode you have to insert the jumper into „CO” terminal on KL08RF side. Look at the instructions below: HEATING MODE: When there is no jumper at „CO”...

  • Page 30: Thermostat Modes

    „A” letter. The VS10WRF/VS10BRF thermostat gives you the possibility to programm schedule. You can add up to 6 programs during one day by selecting the program’s start time and temperature. You can choose from 3 different schedule configurations: •...
  • Page 31 TO SET THE SCHEDULE IN THE APP: Select thermostat in the Press thermostat’s name. Scroll down and press pencil button. main app menu. As you can see there is default schedule. You can delete all default intervals by button. After days period selection use Then add a start time and Choose for which days you want to „Add interval”...
  • Page 32 After you’ve added all the intervals, ADDITIONALLY: You can Select thermostat for which you tap „Save” to save it. Your schedule duplicate the same schedule for want to duplicate the schedule. has been saved and set. other thermostat’s. Click on the „Duplicate schedule”...
  • Page 33 TO SET DEFAULT SCHEDULE: Select thermostat in the Press thermostat’s name. main app menu. To set default schedule use „Default schedule” Scroll down and press pencil icon. button. It will remove all current intervals and it will set default schedule.

  • Page 34: Temporary Override Mode

    6.4.3.2 Temporary override mode Temporary override mode means manual temperature change during active schedule mode: When you overwrote schedule’s setpoint When you have overwritten the temperature When „Follow schedule” mode is active, temperature then on the thermostat’s then hand icon will appear next to calendar use slider to set new setpoint display you will see the hand icon.

  • Page 35: Frost Protection

    6.4.3.4 Frost protection In Frost protection mode the thermostat is displaying actual room temperature and maintain „frost protection” setpoint temperature specified in thermostat settings (please refer to chapter 8.3). When thermostat works in Frost protection mode then you have no possibilities to change temperature setpoint.

  • Page 36: Key Lock Function

    6.4.4 Key lock function You can lock/unlock buttons in your thermostat by application. When buttons are locked then also you Click in the thermostat’s name. Click on the „padlock” icon to can see on the thermostat display „key” lock/unlock thermostat buttons. icon.

  • Page 37: Compatibility With Window/Door Sensor Os600 / Sw600

    OS600 or SW600 (please refer to the OS600 or SW600 manual instruction). To pair window/door sensor OS600/SW600 with VS10WRF/VS10BRF thermostat please follow steps below: Select the thermostat in Press thermostat’s name.

  • Page 38: Compatibility With Smart Plug Spe600

    SPE600 Smart Plug to the SALUS SmartHome system (please refer to the SPE600 manual instruction). To pair SPE600 Smart Plug with VS10WRF/VS10BRF thermostat please follow steps below: Select the thermostat in Press thermostat’s name.

  • Page 39: Compatibility With Smart Relay Sr600

    (or turn off when there is no need to heat). If you want to have acces to this function then first you have to add SR600 Smart Relay to the SALUS SmartHome system (please refer to the SR600 manual instruction).

  • Page 40: Work As A Hot Water Timer (Work Modes)

    6.5 Work as a hot water timer (work modes) VS10WRF/VS10BRF thermostat has 4 work modes as a hot water timer: - Turned ON - (thermostat is manually turned on and work as long as you change this mode to another or switch it off), - AUTO mode - (thermostat is following schedule which you programmed - look at chapter 6.4.3.1 Schedule mode, page 30),...

  • Page 41: Auto Mode

    6.5.2 AUTO mode - Thermostat is following schedule which you programmed - look at chapter 6.4.3.1 Schedule mode, page 29. To set this mode on, please follow steps below: Select AUTO mode. Select the thermostat in the main Close thermostat’s tile. app menu.

  • Page 42: Turned Off Mode

    6.5.3 Turned OFF mode - Thermostat is manually turned off as long as you select other mode. To set this mode on, please follow steps below: Turn OFF thermostat. Select the thermostat in the main Close thermostat’s tile. app menu. Thermostat is turned off.

  • Page 43: Temporarily On Mode

    6.5.4 Temporarily ON mode - You can fast set the water heating time in this mode in limited hour period (from 1 to 4 hours). To set this mode on, please follow steps below: Select temporarily mode (B letter). Choose hour value. Select the thermostat in the main app menu.

  • Page 44: Identification Mode

    6.6 Identification mode Identification mode can be useful when we are pairing more than one device in one moment and we don’t know which device is which. Beyond, if our system include more that one UGE600 Universal Gateway then we can easily identify which device is paired with which gateway. Select the thermostat in Press thermostat’s name.

  • Page 45: Pinning/Unpinning Thermostat To/From Application Dashboard

    To pin/unpin thermostat from dashboard in Smart Home application please follow steps below: Open main menu in the app. Select equipment. Select All equipment option. Select your VS10WRF/VS10BRF Press on the „Pin” icon to pin/unpin thermostat. thermostat to/from the app dashboard.

  • Page 46: User Settings (Basic Settings)

    6.8 User settings (basic settings) User settings of VS10WRF/VS10BRF thermostat determine basic thermostat parameters. Please see below how to enter those settings: Select the thermostat in Press thermostat’s name. Select thermostat’s settings. the main app menu. Scroll down to the settings section.

  • Page 47: Admin Settings (Installer Parameters)

    6.9 Admin settings (installer parameters) PLEASE NOTE: Admin settings are mainly for qualified installers or knowledgeable users. Select the thermostat in Press thermostat’s name. the main app menu. Scroll down to enter Select thermostat’s settings. „Admin settings”. Please Note: All service parameters with detailed admin settings are described on page 74!

  • Page 48: Onetouch Rules (Add/Edit)

    6.10 OneTouch rules (add/edit) OneTouch - function that distinguish SALUS Smart Home system in terms of functionality. OneTouch rules are pre-configured set of actions defined in the interface easy in use. You can switch it on or off anytime. OneTouch informs thermostat or other device how it has to work according to pre-set settings.
  • Page 49 You can also create your own OneTouch rule. As an example we will create OneTouch rule which activates „send me a notification” action under „temperature is below 10 °C” condition. Please look at the steps below how to set this OneTouch rule. Open main menu in the app.
  • Page 50 Select which thermostat you want to Choose the condition details for your Enter a temperature setpoint trigger link up with your OneTouch rule. thermostat. In this case select for your OneTouch rule. Press „Set” „Temperature Below” option. button to confirm. To finish OneTouch rule creation press Select „DO THIS”...
  • Page 51 As an option OneTouch rule tile can be Newly created OneTouch rule tile can be ... and on your dashboard. pinned to the dashboard. found under OneTouch main menu... To force OneTouch rule activation select ...and press it’s button. OneTouch rule is now activated. In this it tile...

  • Page 52: Error Codes (Exclamation Mark In App)

    6.11 Error codes (exclamation mark in app) If there is any error in the Smart Home system which relates to the devices performance or functionality then the Smart Home app will inform user about it by a red exclamation mark in the upper menu. Please look at the example below: Press the exclamation mark button.

  • Page 53: Wireless Signal Strength Test

    PLEASE NOTE: Every Smart Home system device which is powered 230VAC is also working as a signal repeater of ZigBee network. If system is based on battery devices there could be a need to use repeaters like Salus RE600, Salus RE10RF or any other device of Salus Smart Home series...

  • Page 54: Factory Reset (Removing Thermostat From The App And Zigbee Network)

    6.13 Factory reset (removing thermostat from the app and ZigBee network) To make thermostat factory reset and remove it from the ZigBee network please follow steps below: Select the thermostat in Press thermostat’s name. the main app menu. At the very bottom of Press „Delete”...
  • Page 55 You can also do factory reset from the thermostat directly. It will also remove your thermostat from the Zigbee network but you still will be able to see thermostat’s tile. After factory reset thermostat tile will change to dark grey colour. 5 sec.

  • Page 56: Installation In Offline Mode Without Salus Smarthome Application

    Please note! If your system has been installed in the OFFLINE mode using the UGE600 Universal Gateway and then connected to the Internet, all devices should be found in the SALUS Smart Home application (using „Scan for equipment” button). All devices found in the application don’t need to be reconfigured, because all settings are automatically copied from the gateway.

  • Page 57: Configuration As A Programmable Thermostat

    7.2 Configuration as a programmable thermostat 7.2.1 Pairing with underfloor heating wiring centre (KL08RF/Control Box) PLEASE NOTE! For easier installation, please make sure you have already added Underfloor Heating Wiring Centre / Control Box KL08RF to your ZigBee network (please refer to the wiring centre manual instruction).
  • Page 58 REPLACE ZONE: You can replace zone on the wiring centre, which is occupied by other thermostat (it will remove it from that zone). To do it follow steps below: When thermostat is succesfully Press button to confirm zone Confirm by button.

  • Page 59: Pairing With Wireless Trv Radiator Head

    7.2.2 Pairing with wireless TRV radiator head PLEASE NOTE! For easier installation, please make sure you have already added wireless TRV radiator heads to your ZigBee network (please refer to the wireless TRV radiator head manual instruction). 5 sec. 5 sec. Set your thermostat for radiators Now thermostat is looking for the Open the ZigBee network.

  • Page 60: Pairing With Rx10Rf Receiver

    7.2.3 Pairing with RX10RF receiver PLEASE NOTE! For easier installation, please make sure you have already added RX10RF receiver to your ZigBee network (please refer to the RX10RF receiver manual instruction). 5 sec. 5 sec. 5 sec. Now thermostat is looking for the buttons to: Hold buttons for 5...

  • Page 61: Configuration As A Hot Water Timer

    7.3 Configuration as a Hot Water timer 7.3.1 Pairing with Room Extension Receiver (RX2) PLEASE NOTE! For easier installation, please make sure you have already added other devices to your ZigBee network, such as Underfloor Heating Control Box (KL08RF) or RX10RF. 5 sec.
  • Page 62 5 sec. 5 sec. When thermostat is succesfully Close the ZigBee network. paired main screen will be displayed.

  • Page 63: Vs10Wrf/Vs10Brf Thermostat - Additional Configuration Options

    Programmable thermostat - as a group controller (MASTER) When VS10WRF/VS10BRF thermostat works as a MASTER (group controller) it means it takes control of up to 7 SLAVE thermostats (please see below SLAVE mode description). Within one KL08RF wiring centre can be managed 2 thermostat groups. Functions such as: setpoint temperature change from schedule, holiday mode, party mode or frost protection mode are managed by MASTER thermostat.

  • Page 64: Vs10Wrf/Vs10Brf Thermostats Grouping (Master And Slave Operation)

    7.4.2 VS10WRF/VS10BRF thermostats grouping (MASTER and SLAVE operation) In this chapter you will learn how to set VS10WRF/VS10BRF thermostat as a group controller (MASTER) or group thermostat (SLAVE). Please look at the instructions below: VS10WRF/VS10BRF AS A GROUP CONTROLLER (MASTER): 5 sec.
  • Page 65 Now you have to set different VS10WRF/VS10BRF as a slave thermostat: 5 sec. 5 sec. 5 sec. Set your thermostat for underfloor Hold buttons for 5 Set thermostat as a non-programmable heating by „ ” or „ ” buttons. seconds to expand menu.

  • Page 66: Operating In Offline Mode

    8.1.1 Work modes VS10WRF/VS10BRF offers 7 work modes. Frame on a given icon indicates which mode is currently active. In manual mode only one temperature level is maintained (3 types of pre-defined setpoint temperature for manual mode ). Thermostat follows programmed schedule when AUTO mode is active („A”...

  • Page 67: Heat/Cool Mode Change (Kl08Rf Connection)

    8.1.2 Heat/cool mode change (KL08RF connection) VS10WRF/VS10BRF thermostat is designed to work in heating and cooling systems. By default thermostat is set to heating mode. To change from heating to cooling mode it’s necessary to insert jumper into „CO” terminal (KL08RF wiring centre). Look at the instructions below: HEATING MODE: „CO”...

  • Page 68: Work As A Hot Water Timer With Rx10Rf Receiver

    8.2 Work as a hot water timer with RX10RF receiver 8.2.1 Work modes VS10WRF/VS10BRF thermostat as a Hot Water timer has 4 modes available: - Turned ON - thermostat is manually turned on and work as long as you change this mode to another or switch it off, - AUTO mode - thermostat is following schedule which you programmed - look at chapter 8.4.1 Schedule mode, page 65,...

  • Page 69: User Settings (Basic Settings)

    8.3 User settings (basic settings) 8.3.1 Schedule mode - programming schedule To program schedule in offline mode please follow steps below: 3 sec. Hold button for 3 seconds to Enter into the schedule settings. enter the menu. There are 4 possible schedule variants. Use and buttons to select schedule variant and confirm by button: Separate schedule for WORKING DAYS.
  • Page 70 Schedule programming example for the WORKING DAYS variant: buttons to set hour. buttons to set Select schedule variant by button. Confirm by button. minutes. Confirm by button. Schedule editing will jump to the Confirm by button. Use and buttons to choose next program’s time setting.

  • Page 71: Time/Date

    8.3.2 Time/Date Time/date change or edit can be done only in Offline mode. In Online Mode thermostat will synchronise current time and date based on information taken from the Internet. To set time/date follow steps below: 3 sec. Go to the time and date settings Hold button for 3 seconds to Choose time and date settings option...

  • Page 72: Thermostat Calibration

    8.3.3 Thermostat calibration Thermostat calibration is a function which allows user to recalibrate internal thermostat’s temperature sensor by a given number of degrees (in the range from -3,0 °C to 3,0 °C in 0,5 °C steps). To calibrate thermostat’s temperature sensor please follow steps below: 3 sec.

  • Page 73: Key Lock Function

    8.3.4 Key lock function To LOCK/UNLOCK VS10WRF/VS10BRF thermostat keys in OFFLINE MODE you have to press and hold buttons for 3 SECONDS. When thermostat is locked, you will see padlock icon on the display. When thermostat is unlocked padlock icon is not visible.

  • Page 74: Installer Parameters

    9. Installer parameters To enter installer parameters please follow steps below. Please refer to parameters table description before any changes. Use buttons to move up or down between all parameters. Every change/selection confirm by button: Hold buttons for 5 to choose seconds to enter the installer mode.
  • Page 75 Parameter Default Function Description Values Values Standard ON/OFF algorithm d06 (only Automatic selection TRV control algorithm with TRV) Advanced self-learning algorithm Disable Valve protection Enable Frost protection temperature 5-17°C Frost protection temperature (and for holiday mode) 5°C 12 hours Time format 24 hours Time zone (reserved for from -13 to...

  • Page 76: Factory Reset

    10. Factory Reset To RESET VS10WRF/VS10BRF thermostat to it’s factory default settings please follow steps below: 5 sec. 5 sec. 5 sec. Hold buttons for 5 buttons Press button to confirm. seconds to enter the installer mode. to choose code „47”.

  • Page 77: Error Codes (Error Codes Description With Possible Solutions)

    • Reinstall the TRV head or replace it. If necessary, contact with the TRV paired with thermostat - TRV hardware error. SALUS Technical Department. XX-01 • Set the heating medium temperature or change D14 parameter. Floor is overheated (heating mode).
  • Page 78 ERROR DISPLAY ERROR DESCRIPTION TROUBLESHOOTING CODE DESCRIPTION (change setpoint temperature). • If LED diode of the Network Status is flashing, pair the wiring centre with the system in accordance to the manual instruction and pair thermostat with wiring centre. • Check TRV head batteries. •...
  • Page 79 • Reinstall the TRV head or replace it. If necessary, contact with the TRV head has a problem with the XX-30 internal gear mechanism. SALUS Technical Department. • Check assembly of the TRV head on radiator valve insert and reinstall Adaptation error of the TRV head the TRV head.

  • Page 80: Cleaning And Maintenance

    SALUS Controls warrants that this product will be free from any defect in materials or workmanship, and shall perform in accordance with its specification, for a period of five years from the date of installation. SALUS Controls sole liability for breach of this warranty will be (at its option) to repair or replace the...
  • Page 81 SALUS Controls is a member of the Computime Group. Maintaining a policy of continuous product development SALUS Controls plc reserve the right to change specification, design and materials of products listed in this brochure without prior notice. Issued: II 2020...

This manual is also suitable for:

Vs10brf

Table of Contents