Summary of Contents for Follett Maestro Chewblet 400 Series
Page 1
Follett ® Maestro Chewblet ® 400 Series ™ Ice Machine and Top Kit for Lancer countertop ice and beverage dispensers Order parts online Installation, Operation and Service Manual www.follettice.com Following installation, please forward this manual to the appropriate operations person.
After uncrating and removing all packing material, inspect the equipment for concealed shipping damage. If damage is found, notify the shipper immediately and contact Follett Corporation so that we can help in the fi ling of a claim, if necessary.
Separate drains for ice machine and condenser. To prevent back fl ow, do NOT connect drains. • Follett recommends installation of a Follett water fi lter system (part# 00130229) in ice machine inlet water line Field Wiring: countertop and wall mount dispensers with RIDE™ remote ice delivery model ice machines Consult enclosed D400A/W, R400A/W, MCD400A/W manual.
Page 5
Dimensions and clearances Required clearances – MCD400 series Entire front of ice machine clear of obstruction/connections to allow removal. 12" (305 mm) above ice machine for service 6" (153 mm) minimum between louvered (exhaust) side of ice machine and any adjacent equipment. MCD400AHS –...
Installation Install Lancer ice dispenser according to manufacturer’s specifi cations. Note: We recommend that the dispenser back be mounted at least 1" (26mm) from wall to allow water, drain and electric lines from top mount ice machines to be concealed behind dispenser. 2.
Page 7
Agitation adjustments - Lancer FS Series Initialization Screen (Boot Up Only) Lancer FS-16 Ver. 0.200 ➊ Main Menu Sub-Catagory FS-16 Setup Brands Per Side Major/Minor V:1 L:2 R:1 FS-16 Setup Bonus Key Setup Config Bonus Key V:1 T:F M:S B:W FS-16 Setup Soda/Plain Water Cancel...
Page 8
For dispensers with RIDE model ice machines Go directly to step 18. Fig. 4 Top mounted ice machine installation 9. Position Follett MCD400AHT ice machine on perimeter gasket of stainless steel top. Ice machine should be oriented with A/C condenser facing front (Fig. 4).
Page 9
3/8" OD Note: Follett recommends the installation water inlet of a Follett water fi lter system (part# Drain 00130229) on supply water inlet. 3/4" MPT...
Page 10
Fig. 7 13. Remove ice machine top panel and louvered side panel. ice transport tube 14. Insert ice transport tube to a 1/2" (13mm) depth through mounting bracket (Fig. 7 and 8.1) and secure transport tube away from condenser fan under fl oat reservoir bracket 1/2"...
Page 11
RIDE model ice machine installation Fig. 9 – Single ice tube dispensers rear entry chase 18. Ice transport tube chase may be located behind or to either side of the dispenser (Fig. 9 and 10). Using the chase mounting bracket as a template 1.25"...
Page 12
20. Follow the “RIDE model ice machine installation procedure” found in the Symphony MCD400 Ice machine Manual 208600 to install your Follett ice machine. 21. Route the bin signal cord from the 4" x 4" (102mm x 102mm) junction box through the top knockout (Fig. 12.2) and countertop hole.
Page 13
Fig. 13 23. Connect the ice transport tube(s) to the dispenser: a) Drill 3/16" (5mm) holes through both sides of the tube 1/2" (13mm) from the tube end. b) Collapse tube and insert through gasketed hole (Fig. 7). c) Match tube holes to bracket tabs. 24.
Combine 1 oz (250ml) bleach with 2 gal (8L) hot water or equivalent 5.25% sodium hypochlorite solution. Solution B – Ice machine cleaner: Prepare one gallon (3.8L) of Follett SafeCLEAN ™ ice machine cleaner (one 7 oz packet) or equivalent. Solution temperature must be at least 120 F (49 C) Warning: Most ice machine cleaners contain citric or phosphoric acid that can cause skin irritation.
Page 15
17. Rinse ice compression nozzles (Fig. 16.1) with water and reinstall. 18. Drain any remaining sanitizing solution from reservoir through fl oat/evaporator drain line (Fig. 15.1). 19. Fill reservoir (Fig. 15.2) with 120 F (49 C) water. Empty water through fl oat/evaporator drain line (Fig. 15.1). Repeat 3 times. 20.
Service Order parts online www.follettice.com Replacement parts Models MTL22SC and MSL22SC Reference # Description Part # Base, top mount 00113514 Base, RIDE model 00113308 Cabinet 00113324 Cover 00113357 Chase, upper 00113381 Chase, lower 00113399 Collar 00113407 Defl ector, single 501616 Box, thermostat 00113449 Gasket, top, Harmony...
Page 20
Harmony, Maestro, SafeCLEAN and RIDE are trademarks of Follett Corporation. Chewblet and Follett are registered trademarks of Follett Corporation, registered in the US. 801 Church Lane • Easton, PA 18040, USA Toll free (877) 612-5086 • (610) 252-7301 00117267R02 www.follettice.com...