Kenwood TS-570D, TS-570S Instruction Manual page 14

3 GETTING ACQUAINTED
1
2
3
4
5
6 !7 !7 !7 !7 !7 Frequency control buttons
These buttons control functions related to selecting a
frequency, a VFO, or a memory channel.
• UP/DOWN buttons
7
Press to step through all Amateur bands
consecutively {page 13} or to step the transceiver
frequency in 1 MHz increments {page 29}. Also
8
used for making selections from the Menu
{page 16}, and to check Start and End frequencies
for the Scan function {page 43}.
• SPLIT button
9
Press to use split-frequency operation which allows
a different transmit frequency and receive frequency
{page 23}.
10
• M/V button
Press to select either Memory or VFO mode
{page 40}.
11
• TF-SET button
While operating split-frequency, press to monitor or
change your transmit frequency {page 23}.
12 • A=B button
Press to copy the data in the currently selected VFO
over to the other VFO {page 30}.
• A/B button
13
Press to select either VFO A or VFO B {page 13}.
Also, in menu mode, press to select either Menu A
or Menu B {page 16}.
14
• CLEAR button
Press to reset the RIT/XIT frequency offset to zero
{pages 30, 32}.
15
• RIT button
Press to switch ON or OFF the Receive Incremental
Tuning function {page 30}.
16
• XIT button
Press to switch ON or OFF the Transmit
Incremental Tuning function {page 32}.
8
POWER
PF
HF TRANSCEIVER TS-570D
ATT PRE-AMP
VOX PROC
SEND AT TUNE
CH1 CH2 CH3
MIC
PHONES
1 2 3
ANT REC FINE
PWR
CW
4 5 6 FSK
MIC
NB AGC/TONE REV
KEY
FM
7 8 9
AM
F.LOCK
DELAY MENU
0
CLR ENT
UP
DOWN
LSB
USB
SPLIT TF-SET
M/V A=B
1MHz
SCAN
!7 !8
!8 !8 !8 !8 !8 SCAN button
Press to start and stop Scan functions {pages 46, 47}.
!9 !9 !9 !9 !9 M>VFO button
Press to transfer data from a memory channel to a VFO
{page 42}.
@0 @0 @0 @0 @0 M.IN button
Writes data into a memory channel {page 39} or selects
Memory Scroll mode {page 41}.
@1 @1 @1 @1 @1 Quick Memory buttons
Controls the Quick Memory function {page 44}.
• M.IN button
Press to write data into Quick Memory {page 44}.
• MR button
Press to recall data from Quick Memory {page 45}.
@2 @2 @2 @2 @2 FILTER button
Press to select the receive filter bandwidth in SSB, CW,
FSK, or AM mode {pages 36, 38}, or press to select
either narrow-band or wide-band transmit deviation in
FM mode {page 22}.
Note: Selecting the narrow filter bandwidth in SSB mode requires
the optional YK-88SN-1 filter {page 36}.
@3 @3 @3 @3 @3 CW TUNE button
Press to activate the automatic zero-beat function for
CW mode {page 21}.
@4 @4 @4 @4 @4 B.C. button
Press to switch ON or OFF the DSP Beat Cancel
function {page 38}.
@5 @5 @5 @5 @5 N.R. button
Press to toggle between Noise Reduction 1, Noise
Reduction 2, and OFF {page 38}.
@2 @3 @ 4 @ 5
@1
DSP SLOPE
HIGH LOW
N.R.
B.C.
CW TUNE
FILTER
AF
RIT/XIT
4
MR
2
– +
M.IN
0
A/B RIT
CH IF SHIFT
4
CLEAR XIT
2
M>VFO M.IN
0
!9 @0
RF
6
8
10
SQL
6
8
10