Chapter 12 Operator Conveniences; Microprocessor Reset; Initial Settings; Partial Reset - Kenwood TS-570D, TS-570S Instruction Manual

OPERATOR CONVENIENCES

MICROPROCESSOR RESET

1
If your transceiver seems to be malfunctioning, resetting
the microprocessor default settings may resolve the
problem.
2

INITIAL SETTINGS

For each VFO, the factory defaults for operating
3
frequency and mode are as follows:
• VFO A: 14.000.000 MHz/ USB
• VFO B: 14.000.000 MHz/ USB
4
The Conventional and Quick memory channels have no
data stored.
5

PARTIAL RESET

Do Partial Reset if a button or control does not function
according to the instructions in this manual. The
6
following are not erased by Partial Reset.
• Memory channel data
• Menu settings
7
• Antenna tuner preset data
• ANT 1/ANT 2 data.
To do Partial Reset, press [A/B]+ POWER ON.
8
• "HELLO" appears on the display.

FULL RESET

9
Do Full Reset if you want to erase all data in all memory
channels. In addition, this function resets all settings,
that you customized, to the factory defaults, i.e. menu
10
settings, antenna tuner preset data, etc.
To do Full Reset, press [A=B]+ POWER ON.
• "HELLO" appears on the display.
11
Note: The IF filter selection in Menu No. 46 will not be reset.

SWITCHING ANT 1/ ANT 2

12
After connecting antenna feed line to the ANT 1
connector and/or ANT 2 connector on the rear panel,
select ANT 1 or ANT 2, depending on which antenna is
used for transmitting and receiving.
13
Press [ANT] to select ANT 1 or ANT 2.
• "ANT 1" or "ANT 2" appears to show which antenna
is selected.
14
15
16
48
The ANT 1/ANT 2 setting will automatically be stored in
the current band. Each time you select the same band,
the same setting will automatically be selected.
The frequency range of each band is shown below.
Frequency Range
(MHz)
0.03 ~ 2.50
2.50 ~ 4.10
4.10 ~ 7.50
7.50 ~ 10.50
10.50 ~ 14.50
30.00 ~ 60.00 (TS-570S)
Note: Connect an external antenna tuner to the ANT 1 connector
only. After connecting this tuner correctly and selecting ANT 1, the
internal tuner will always be bypassed.

FREQUENCY LOCK FUNCTION

Frequency Lock disables some buttons and controls to
prevent you from accidentally activating a function or
disturbing current settings.
Press [F.LOCK] to toggle Frequency Lock ON or OFF.
• "F.LOCK" appears when the function is ON.
The following buttons and controls are disabled by
Frequency Lock:
• Tuning control
• QUICK MEMO [MR]
• [FINE] • [REV]
• [ENT] • [LSB/USB]
• [FM/AM] • [1MHz]
• [SPLIT] • [A/B]
• [A=B] • [SCAN]
• [M.IN]
Note:
After activating Frequency Lock, the MULTI/CH control and
[UP]/[DOWN] are still available in Menu mode.
After activating Frequency Lock, you can still change the transmit
frequency with the Tuning control while using the TF-SET
function.
After activating Frequency Lock, the MULTI/CH control is still
available for selections other than frequency and memory
channel changes.
After activating Frequency Lock, [CLR] is still available in some
situations.
Frequency Range
(MHz)
14.50 ~ 18.50
18.50 ~ 21.50
21.50 ~ 25.50
25.50 ~ 30.00
• MULTI/CH control
• QUICK MEMO [M.IN]
• [CLR]
• [CW/FSK]
• [UP]/[DOWN]
• [M/V]
• [M>VFO]