Related Manuals for AXIOMTEK SHB210 Series
Summary of Contents for AXIOMTEK SHB210 Series
- Page 1 SHB210 Series ® ™ ™ Intel Core 2 Duo/ Core ™ ® Core Solo/ Celeron PICMG 1.3 Half-Size Single Board Computer User’s Manual...
- Page 2 AXIOMTEK does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. AXIOMTEK does not make any commitment to update the information in this manual.
-
Page 3: Esd Precautions
Wear a wrist-grounding strap, available from most electronic component stores, when handling boards and components. Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co., Ltd. ® Windows is a trademark of Microsoft Corporation. Phoenix & AWARD are trademarks of Phoenix Technology Ltd. -
Page 4: Table Of Contents
Table of Contents Disclaimers ......................ii ESD Precautions ....................iii C h a p t e r 1 ......................1 Introduction......................... 1 Specifications ................. 2 Utilities Supported ................. 3 Block Diagram ................4 I/O Bracket ..................4 C h a p t e r 2 ......................5 Jumpers and Connectors .................. - Page 5 C h a p t e r 4 ......................25 Hardware Description ....................25 Microprocessors ................25 BIOS....................25 System Memory................25 I/O Port Address Map ..............26 C h a p t e r 5 ......................27 Award BIOS Utility ....................27 Entering Setup................
- Page 6 MEMO...
-
Page 7: Introduction
SHB210 Socket M Half-Size SBC User’s Manual C h a p t e r 1 Introduction The SHB210 PICMG 1.3 half-size Single Board Computer supports ® ™ ™ ™ ® Intel Core 2 Duo/Core Duo/Core Solo/Celeron M processors, ® at FSB 533/667 MHz. The board integrates chipsets Intel 945GM and ICH7M-DH that deliver outstanding system performance through high-bandwidth interfaces, multiple I/O functions for interactive... -
Page 8: Specifications
SHB210 Socket M Half-Size SBC User’s Manual Specifications ® ™ ™ ™ ® /Celeron CPU: Intel Core 2 Duo/Core Duo/Core Solo processors ® System Chipset: Intel 945GM/ICH7M-DH CPU Socket: Socket M Front-Side Bus: 533/667 MHz BIOS Award PnP Flash BIOS System Memory Two x 200-pin DDR2 SO-DIMM sockets Maximum up to 4GB DDR2 memory... -
Page 9: Utilities Supported
SHB210 Socket M Half-Size SBC User’s Manual Ethernet The LAN1/LAN2 is 8111B Ethernet controller support 10/100/1000 Mb Dual PCI-Express LAN Serial ATA Support Serial ATA/Serial ATA II Two Serial ATA channels for a total of two Serial ATA hard drives Maximum transfer rate could up to 300MB/sec Hardware Monitoring Controller: Winbond W83627HG-AW... -
Page 10: Block Diagram
SHB210 Socket M Half-Size SBC User’s Manual Block Diagram I/O Bracket Introduction... -
Page 11: Chapter 2
SHB210 Socket M Half-Size SBC User’s Manual C h a p t e r 2 Jumpers and Connectors Board Dimensions Jumpers and Connectors... -
Page 12: Board Layout
SHB210 Socket M Half-Size SBC User’s Manual Board Layout Top Side Bottom Side Jumpers and Connectors... -
Page 13: Jumper Settings
SHB210 Socket M Half-Size SBC User’s Manual Jumper Settings Proper jumer settings configure the SHB210 to meet your application purpose. 2.3.1 COM2 Mode Select Jumpers: JP2, JP3, JP4 These jumpers select the COM1 port’s communication mode to operate RS-232 or RS-422/485. Description Function Jumper Setting... -
Page 14: Compact Flash Voltage Selection Jumper: Jp8
SHB210 Socket M Half-Size SBC User’s Manual 2.3.3 Compact Flash Voltage Selection Jumper: JP8 This jumper is to select the voltage for Compact Flash interface. Description Function Jumper Setting Function Jumper Setting 3.3V (Default) Voltage 2.3.4 COM1 DCD and Voltage Selection Jumper: JP1 Jumper Description Jumper Setting Description... -
Page 15: Connectors
Ethernet Connector 2 Audio Connector CN12 Ethernet Connector 1 CN23 EPIC Power Connector External Speed LED Ethernet Connector 1 CN22 AXIOMTEK LVDS LCD CN16 Interface External Link/ACT LED Ethernet Connector 2 CN25 LCD Power Connector CN21 External Speed LED Ethernet Connector 2... -
Page 16: Front Panel Output Connector: Cn1
SHB210 Socket M Half-Size SBC User’s Manual 2.4.1 Front Panel Output Connector: CN1 2.4.2 Printer Port Connector: CN2 Print Port Connector This board has a multi-mode parallel port to support the following modes: 1. Standard Mode: IBM PC/XT, PC/AT and PS/2™ are compatible with bi-directional parallel port. -
Page 17: Epic Power Connector: Cn4
SHB210 Socket M Half-Size SBC User’s Manual CN2: Pin Assignment Table Signal Signal 1 Strobe# 2 Auto Form Feed# 3 Data 0 4 Error # 5 Data 1 6 Initialize # 7 Data 2 8 Printer Select In # 9 Data 3 10 GND 11 Data 4 12 GND... -
Page 18: Serial Port Interface Connectors: Com1, Com2
SHB210 Socket M Half-Size SBC User’s Manual 2.4.5 Serial Port Interface Connectors: COM1, COM2 The serial interface for the board consists of COM1 port support RS232/422/485(COM1) and COM2 (COM2) supports RS-232. Signal Signal COM1, COM2 Data Carrier Detect Data Set Ready (DSR) (DCD) Receive Data (RXD) Request to Send (RTS) -
Page 19: Ide Interface Connector: Cn3
SHB210 Socket M Half-Size SBC User’s Manual 2.4.7 IDE Interface Connector: CN3 The board provided one IDE Port to support maximum up to two IDE devices. Description Description Description Reset # Data 7 Data 8 Data 6 Data 9 Data 5 Data 10 Data 4 Data 11... -
Page 20: Lvds/Lcd Connectors: Cn14, Cn16, Cn21
SHB210 Socket M Half-Size SBC User’s Manual 2.4.8 LVDS/LCD Connectors: CN14, CN16, CN21 There are several connectors to support CRT VGA and flat panel displays. CN14 is a standard 15-pin connector commonly used for the CRT VGA display, CN16 a Hirose DF20-40pin connector for the LVDS flat panel connection, and CN21 a Hirose DF13-7pin connector for inverter. - Page 21 SHB210 Socket M Half-Size SBC User’s Manual Signal Signal LVDSA_D2- LVDSA_CLK- LVDSA_D2+ LVDSA_CLK+ CN16 Hirose DF13-7pin LCD Power Connector for Inverter: CN21 Signal CN21 ENAB Jumpers and Connectors...
-
Page 22: Ethernet Connectors: Cn5, Cn7
SHB210 Socket M Half-Size SBC User’s Manual CRT Connector: CN14 CN14 is a standard 15-pin pin DB15 connector commonly used for the CRT VGA display. Signal Signal Signal Green Blue AGND AGND AGND DDC DAT Horizontal Sync Vertical Sync DDC CLK CN14 2.4.9 Ethernet Connectors: CN5, CN7 The RJ-45 connectors CN5 and CN7 are for Ethernet. -
Page 23: Usb Connectors: Cn10, Cn11
SHB210 Socket M Half-Size SBC User’s Manual 2.4.10 USB Connectors: CN10, CN11 These Universal Serial Bus (USB) connectors on this board are for installing versatile USB interface peripherals. These are 10-pin standard USB connectors. CN10, CN11 Signal Signal 1 USB USB POWER POWER 3 USB P0-... -
Page 24: Front Panel Connector
SHB210 Socket M Half-Size SBC User’s Manual 2.4.12 Front Panel Connector Power LED Pins 1, 3, 5 connect the system power LED indicator to its respective switch on the case. Pin 1 is +, and pin 5 assigned to -. Pin 3 is defined as NC. -
Page 25: External Mouse/Keyboard Connectors: Cn9/Cn13
SHB210 Socket M Half-Size SBC User’s Manual 2.4.13 External Mouse/Keyboard Connectors: CN9/CN13 The board provides a keyboard (CN13) and Mouse (CN9) interface with two 5-pin connectors. Clock Data No Connection Power 2.4.14 SYSTEM FAN1/FAN2/FAN3 Connectors: You can connect the system cooling fan cable to FAN1/FAN2/FAN3 for system cooling fan power. -
Page 26: Ethernet Connector 1 External Speed Led: Cn23
SHB210 Socket M Half-Size SBC User’s Manual 2.4.16 Ethernet Connector 1 External Speed LED: CN23 Signal CN23 100, Low Active 3.3V Gigibit, Low Active 2.4.17 Ethernet Connector 2 External Act/Link LED: CN24 Signal CN24 3.3V Link active 2.4.18 Ethernet Connector 1 External Act/Link LED: CN22 Signal CN22... -
Page 27: Chapter 3
SHB210 Socket M Half-Size SBC User’s Manual C h a p t e r 3 Hardware Installation ® Before installing the processor, please access Intel website for more detailed information http://www.intel.com . Installing the Processor The Intel® Pentium® M Processor is available as a boxed processor for laptop computers in the micro-FCPGA form factor. - Page 28 SHB210 Socket M Half-Size SBC User’s Manual 3. If the cooling solution prevents you from accessing the processor socket, you may need to remove it. Instructions on how to remove your cooling solution should be provided in the documentation that came with the system. 4.
-
Page 29: Installing The Memory
SHB210 Socket M Half-Size SBC User’s Manual Installing the Memory The board supports two 200-pin DDR2 SO-DIMM memory sockets with maximum memory capacity up to 4GB. Please follow steps below to install the memory modules: Push down latches on each side of the SO-DIMM socket. Align the memory module with the socket that notches of memory module must match the socket keys for a correct intallation. - Page 30 SHB210 Socket M Half-Size SBC User’s Manual MEMO Hardware Installation...
-
Page 31: Chapter 4
Make sure all correct settings are arranged for your installed microprocessor to prevent the CPU from damages. BIOS The SHB210 Series uses Award Plug and Play BIOS with a single 4Mbit Flash EPROM. System Memory The SHB210 Series supports two 200-pin DDR2 SO-DIMM sockets for a maximum memory of 4GB. -
Page 32: I/O Port Address Map
SHB210 Socket M Half-Size SBC User’s Manual I/O Port Address Map ® ™ ™ ™ ® The Intel Core 2 Duo/ Core Duo/Core Solo, Celeron M CPUs can communicate via I/O ports. There are total 1KB port addresses available for assignment to other devices via I/O expansion cards. Address Devices 000-01F... -
Page 33: Chapter 5
SHB210 Socket M Half-Size SBC User’s Manual C h a p t e r 5 Award BIOS Utility The Phoenix-Award BIOS provides users with a built-in Setup program to modify basic system configuration. All configured parameters are stored in a battery-backed-up RAM (CMOS RAM) to save the Setup information whenever the power is turned off. -
Page 34: Control Keys
SHB210 Socket M Half-Size SBC User’s Manual Control Keys Move cursor to the previous item Up arrow Move cursor to the next item Down arrow Move cursor to the item on the left hand Left arrow Move to the item in the right hand Right arrow Main Menu -- Quit and delete changes into CMOS Status Page Setup Menu and Option Page Setup... -
Page 35: The Main Menu
SHB210 Socket M Half-Size SBC User’s Manual The Main Menu Once you enter the Award BIOS CMOS Setup Utility, the Main Menu appears on the screen. In the Main Menu, there are several Setup functions and a couple of Exit options for your selection. Use arrow keys to select the Setup Page you intend to configure then press <Enter>... -
Page 36: Standard Cmos Setup Menu
SHB210 Socket M Half-Size SBC User’s Manual Standard CMOS Setup Menu The Standard CMOS Setup Menu displays basic information about your system. Use arrow keys to highlight each item, and use <PgUp> or <PgDn> key to select the value you want in each item. Date The date format is <day>, <date>... - Page 37 SHB210 Socket M Half-Size SBC User’s Manual IDE Channel 0 Master/IDE Channel 0 Slave/IDE Channel 1 Master/IDE Channel 1 Slave These items identify the types of each IDE channel installed in the computer. There are 45 predefined types (Type 1 to Type 45) and 2 user’s definable types (Type User) for Enhanced IDE BIOS.
- Page 38 SHB210 Socket M Half-Size SBC User’s Manual Halt On This item determines whether the system will halt or not, if an error is detected while powering up. The system booting will halt on any errors detected. No errors (default) Whenever BIOS detects a non-fatal error, the All errors system will stop and you will be prompted.
-
Page 39: Advanced Bios Features
SHB210 Socket M Half-Size SBC User’s Manual Advanced BIOS Features This section allows you to configure and improve your system, to set up some system features according to your preference. CPU Feature Scroll to this item and press <Enter> to view the CPU Feature sub menu. - Page 40 SHB210 Socket M Half-Size SBC User’s Manual Hard Disk Boot Priority Scroll to this item and press <Enter> to view the sub menu to decide the disk boot priority. Press <Esc> to return to the Advanced BIOS Features page. Virus Warning This option flashes on the screen.
- Page 41 SHB210 Socket M Half-Size SBC User’s Manual NOTE: This function is only available with DOS and other operating systems that do not trap INT13. CPU L1 & L2 Cache These two options speed up memory access. However, it depends on the CPU/chipset design. The default setting is “Enabled”. CPUs without built-in internal cache will not provide the “CPU Internal Cache”...
- Page 42 SHB210 Socket M Half-Size SBC User’s Manual Boot Up NumLock Status Set the the Num Lock status when the system is powered on. The default value is “On”. Security Option This item allows you to limit access to the system and Setup, or just to Setup.
-
Page 43: Advanced Chipset Features
SHB210 Socket M Half-Size SBC User’s Manual Advanced Chipset Features This section contains completely optimized chipset’s features on the board that you are strongly recommended to leave all items on this page at their default values unless you are very familiar with the technical specifications of your system hardware. -
Page 44: Integrated Peripherals
SHB210 Socket M Half-Size SBC User’s Manual DVMT Mode DVMT (Dynamic Video Memory Technology) helps you select the video mode. DVMT/Fixed Memory Size DVMT (Dynamic Video Memory Technology) allows you to select a maximum size of dynamic amount usage of the video memory. The system would configure the video memory dependent on your application. - Page 45 SHB210 Socket M Half-Size SBC User’s Manual OnChip IDE Device Scroll to this item and press <Enter> to view the sub menu OnChip IDE Device. IDE HDD Block Mode Block mode is also called block transfer, multiple commands, or multiple sector read/write. If your IDE hard drive supports block mode (most new drives do), select Enabled for automatic detection of the optimal number of block read/writes per sector the drive can support.
- Page 46 SHB210 Socket M Half-Size SBC User’s Manual automatically remove the IDE Primary Master/ Slave PIO and/or IDE Secondary Master/Slave PIO items on the menu. IDE Primary/Secondary Master/Slave PIO The four IDE PIO (Programmed Input/Output) fields let you set a PIO mode (0-4) for each of the four IDE devices that the onboard IDE interface supports.
- Page 47 SHB210 Socket M Half-Size SBC User’s Manual Onboard Device Scroll to this item and press <Enter> to view the sub menu Onboard Device. USB Controller Enable this item if you are using the USB in the system. You should disable this item if a higher-level controller is added. USB 2.0 Controller Enable this item if you are using the EHCI (USB2.0) controller in the system.
- Page 48 SHB210 Socket M Half-Size SBC User’s Manual Super IO Device Scroll to this item and press <Enter> to view the sub menu Super IO Device. Onboard FDC Controller Select Enabled, if your system has a floppy disk controller (FDC) installed on the system board and you want to use it. If you install and-in FDC or the system has no floppy drive, select Disabled in this field.
-
Page 49: Power Management Setup
SHB210 Socket M Half-Size SBC User’s Manual ECP Mode Use DMA Select a DMA channel for the parallel port while using the ECP mode. PWRON After PWR-Fail This item enables your computer to automatically restart or return to its operating status. Press <Esc>... - Page 50 SHB210 Socket M Half-Size SBC User’s Manual Windows ME and Windows 2000, you can choose to enter the Standby mode in S1 (POS) or S3 (STR) fashion through the setting of this field. Options are: [S1 (POS)] The S1 sleep mode is a low power state. In this state, no system context is lost (CPU or chipset) and hardware maintains all system contexts.
- Page 51 SHB210 Socket M Half-Size SBC User’s Manual Disabled The System will never enter the SUSPEND mode. 1/2/4/6/8/10/2 It defines continuous idle time before the system 0/30/40 entering the SUSPEND mode. Min/1 Hr If any item defined in (J) is enabled and active, the SUSPEND timer will be reloaded.
-
Page 52: Pnp/Pci Configuration Setup
SHB210 Socket M Half-Size SBC User’s Manual 5.10 PnP/PCI Configuration Setup This section describes the configuration of PCI (Personal Computer Interconnect) bus system, which allows I/O devices to operate at speeds close to the CPU speed while communicating with other important components. - Page 53 SHB210 Socket M Half-Size SBC User’s Manual IRQ Resources When resources are controlled manually, assign each system interrupt to one of the following types in accordance with the type of devices using the interrupt: 1. Legacy ISA Devices compliant with the original PC AT bus specification, requiring a specific interrupt (such as IRQ4 for serial port PCI/ISA PnP Devices compliant with the Plug and Play standard, whether designed for PCI or ISA bus architecture.
-
Page 54: Pc Health Status
SHB210 Socket M Half-Size SBC User’s Manual 5.11 PC Health Status This section supports hardware monitering that lets you monitor those parameters for critical voltages, temperatures and fan speed of the board. Current CPU Temperature The current system CPU temperature will be automatically detected by the system. -
Page 55: Load Fail-Safe Defaults
SHB210 Socket M Half-Size SBC User’s Manual 5.12 Load Fail-Safe Defaults When you press <Enter> on this item, a confirmation dialog box pops out to show you such a message: Please press “Y” to load default values that will be factory settings for accomplishing the optimal performance of system operations. -
Page 56: Load Optimized Defaults
SHB210 Socket M Half-Size SBC User’s Manual 5.13 Load Optimized Defaults This option allows you to load your system configuration with default values. These default settings are optimized to enable high performance features. To load CMOS SRAM with SETUP default values, please enter “Y”. If not, please enter “N”. - Page 57 SHB210 Socket M Half-Size SBC User’s Manual Type a maximum eight-character password, and press <Enter>. This typed password will clear previously entered password from the CMOS memory. You will be asked to confirm this password. Type this password again and press <Enter>. You may also press <Esc> to abort this selection and not enter a password.
-
Page 58: Save & Exit Setup
SHB210 Socket M Half-Size SBC User’s Manual 5.15 Save & Exit Setup This section allows you to determine whether or not to accept your modifications. Type “Y” to quit the setup utility and save all changes into the CMOS memory. Type “N” to bring you back to the Setup utility. 5.16 Exit Without Saving Select this option to exit the Setup utility without saving changes you have made in this session. -
Page 59: Chapter 6
Installation of Drivers The device drivers are located on the Product Information CD-ROM that comes with the SHB210 Series package. The auto-run function of drivers will guide you to install the utilities and device drivers under a Windows system. You can follow the onscreen instructions to install... - Page 60 SHB210 Socket M Half-Size SBC User’s Manual ® An Intel License Agreement appears to show you the important information. Click “Yes” to next step. Please wait while running the following setup operations. Instalation of Drivers...
- Page 61 SHB210 Socket M Half-Size SBC User’s Manual Click “Finish” to complete the setup process. Installation of Drivers...
-
Page 62: Installing Vga Driver
SHB210 Socket M Half-Size SBC User’s Manual You will be asked to reboot your computer when the installation is completed. Please click “Yes, I want to restart my computer now” if you don’t need to install any other drivers. Otherwise, please click “No, I will restart my computer later”, and go on next step. - Page 63 SHB210 Socket M Half-Size SBC User’s Manual ® An Intel License Agreement appears to show you the important information. Click “Yes” to next step. The message of Readme File Information appears to show you the system requirements and installation information. Please click “Next”.
- Page 64 SHB210 Socket M Half-Size SBC User’s Manual 4. Please wait while running the following setup operations. 5. When this message appears, please click “Next”. Instalation of Drivers...
- Page 65 SHB210 Socket M Half-Size SBC User’s Manual 6. You will be asked to reboot your computer when the installation is completed. Please click “Yes, I want to restart my computer now” if you don’t need to install any other drivers. Otherwise, please click “No, I will restart my computer later”, and click “Finish”...
-
Page 66: Installing Lan Driver
SHB210 Socket M Half-Size SBC User’s Manual Installing LAN Driver Run the InstallShield Wizard for Ethernet from the driver directory in your driver CD. Click “Next” to next step. Click “Install” to start the installation. Instalation of Drivers... - Page 67 SHB210 Socket M Half-Size SBC User’s Manual Please wait while running the following installation operation. Click “Finish” to complete the installation. 2. When this message appears, please click “Next”. Installation of Drivers...
- Page 68 SHB210 Socket M Half-Size SBC User’s Manual MEMO Instalation of Drivers...
-
Page 69: Appendix
SHB210 Socket M Half-Size SBC User’s Manual A p p e n d i x Watch Dog Timer Please follow the below WDT process for setup the WDT function. Watch Dog Timer... - Page 70 SHB210 Socket M Half-Size SBC User’s Manual MEMO Watch Dog Timer...