Chapter 8. Trigger Settings For Each Pad [Trigger]; Selecting The Pad Type [F1 (Bank)] - Roland V-Drums TD-20X Owner's Manual

Chapter 8. Trigger Settings for Each Pad [TRIGGER]

Here's how to make trigger settings to ensure that the trigger
signals from the pads and pedals are appropriately conveyed
to the sound generator section.
If you specify the model (type) of pad that is connected to
each trigger input jack, the settings suitable for each pad will
be made. To specify the pad type, use the [TRIGGER] button
[F1 (BANK)].
If you want to make additional fine adjustments for each pad
to further adjust the sensitivity etc., you can use the [F2
(BASIC)] or [F5 (ADVANCE)] button to do so.
Selecting the Pad Type
[F1 (BANK)]
To ensure that the signals from the pads can be processed
appropriately by the TD-20X, you must specify the type of
pad you're using (the trigger type) for each trigger input.
Trigger Type
A trigger type is a group of trigger settings with values
optimally adjusted for a particular pad.
In order to make the most suitable settings for the pad
connected to each trigger input, specify the model (type) of
the pad that is connected.
Only when factors unrelated to the selection of the proper
trigger type prevent you from getting good results in
performance should you fine-tune the individual parameters
for the pad you are using.
Trigger Bank
Trigger Banks allow you to store the 15 trigger settings as a
single unit of information. The large number at the left edge
of the above display is the Trigger Bank number. Move the
cursor to this area to select the Trigger Bank.
1.
Press the [TRIGGER] button.
The [TRIGGER] button lights.
2.
Press the [F1 (BANK)] button.
The "TRIGGER BANK" screen will appear.
fig.08-001-bank.eps_70
Trigger bank number
3.
Press the [CURSOR (left)] button to move the cursor
to the trigger bank number.
96
Trigger Type
4.
Use the [-] [+] buttons or the [VALUE] dial to select
the Trigger Bank.
5.
Press the [CURSOR (right)] button to move the
cursor to a trigger type.
6.
Select the pad for which you want to make settings.
Strike the pad, or use the TRIG SELECT buttons to select it.
You can also use the [CURSOR] buttons to select the pad.
7.
Use the [-] [+] buttons or the [VALUE] dial to select
the trigger type.
Trigger
Used Modes
Type
KD-140 KD140
KD-120 KD120
KD-85
KD85
KD-80
KD-8 KD8
KD-7 KD7
PD-125X
PD-125XS PD125X
PD-125
PD-120 PD120
PD-105X
PD-105 PD105X
PD-100
PD-85
PD-80R PD85
PD-80
PDX-8 PDX8
PD-9 PD9
PD-8 PD8
PD-7 PD7
CY-15R CY15R
CY-14C CY14C
CY-12R/C CY12RC
CY-8 CY8
CY-5
CY5/6
CY-6
CY-12H CY12H
VH-12 VH12
VH-11 VH11
Non-Roland
PAD1
pad
Non-Roland
PAD2
pad
RT-10K RT10K
RT-10S RT10S
RT-10T RT10T
Positional
Rim Choke
Sensing
Shot play
Head Rim
✕ ✕ ✕ ✕
✕ ✕ ✕ ✕
✕ ✕ ✕ ✕
✕ ✕ ✕ ✕
✕ ✕ ✕ ✕
❍ ❍ ❍ ✕
❍ ❍ ✕ ✕
❍ ❍ ❍ ✕
❍ ❍ ❍ ✕
❍ ✕ ✕ ✕
❍ ❍ ✕ ❍
❍ ❍ ✕ ❍
❍ ❍ ✕ ❍
❍ ❍ ✕ ❍
❍ ❍ ✕ ❍
❍ ❍ ✕ ❍
❍ ✕ ✕ ❍
❍ ✕ ✕ ❍
❍ ✕ ✕ ❍
❍ ✕ ✕ ❍
❍ ✕ ✕ ❍
❍ ✕ ✕ ❍
❍ ✕ ✕ ✕
✕ ✕ ✕ ✕
❍ ✕ ✕ ✕
✕ ✕ ✕ ✕