Operating Jvc's Audio/Video Components - JVC RX-888VBK Instructions Manual

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.
IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK-3 (SYNCHRO) jacks (see page 36) in addition to the
connections using cables with RCA pin plugs (see pages 5 and 6).
• Aim the remote control directly at the remote sensor on the receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source. To
operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 12.)
• Refer also to the manuals supplied with your components.
STANDBY
TV/CATV/DBS VCR 1
POWER POWER
DVD DVD MUILTI CD TAPE/MD
TV/DBS VIDEO PHONO FM/AM
VCR 1 VCR 2 ANALOG/DIGITAL SLEEP
SURROUND CNTR TONE CNTR
1 2
ON/OFF
MENU MENU
TEST REAR-L
SURROUND
4 5
MODE
ENTER ENTER
DISC
EFFECT REAR-R
7 8
/P
SOUND SEA MODE SUBWOOFER
10 0
RETURN FM MODE/MUTING
MENU
CATV/DBS
SET
EXIT
DISPLAY
TV VOL CHANNEL VOLUME
TV/VIDEO VCR 1 TAPE
CONTROL
/REW PLAY
FF/
DOWN TUNING UP
REC STOP PAUSE
RM-SRX888J REMOTE CONTROL
Tuner
After pressing FM/AM (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations:
FM/AM:
Alternates between FM and AM.
1 – 10, +10:
Selects a preset channel number directly.
For channel number 5, press 5.
For channel number 15, press +10, then 5.
For channel number 20, press +10, then 10.
TUNING UP/TUNING DOWN:
Tunes into stations.
FM MODE/MUTING: Changes the FM reception mode.
ON
3
6
9
+10
100+
AUDIO/
TV/VCR
AUDIO/
TV/VCR
CATV/DBS
TEXT
Check to see if its remote
control mode selector is set
to the correct position.
To operate the audio
MUTING
system, TVs, and VCRs,
set it to "AUDIO/TV/VCR."
Sound control section (Amplifier)
You can always perform the following operations (with the remote
control mode selector set to "AUDIO/TV/VCR"):
SURROUND ON/OFF: Turns on or off the Surround modes —
Dolby Pro Logic, Dolby Digital, and DTS
Digital Surround.
SURROUND MODE: Selects the DSP modes.
After pressing SOUND (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations:
SEA MODE:
Changes the SEA modes.
SUBWOOFER – / +: Adjusts the subwoofer output level.
CNTR – / +: Adjusts the center speaker output level.
REAR•L – / +:
Adjusts the left rear speaker output level.
REAR•R – / +:
Adjusts the right rear speaker output level.
EFFECT:
Selects the effect level.
TEST:
Turns on or off the test tone output.
CNTR TONE:
Selects the center tone.
Note:
After adjusting sounds, press the corresponding source selecting
button or DISC to operate your target source by using the 10 keys;
otherwise, the 10 keys cannot be used for operating your target
source.
CD player
After pressing CD (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations on
the CD player:
PLAY: Starts playing.
4 4 4 4 4 :
Returns to the beginning of the current (or
previous) track.
¢ ¢ ¢ : ¢ ¢
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.
For track number 20, press +10, then 10.
For track number 30, press +10, +10, then 10.
CD player-changer
After pressing DISC (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations on a
CD player-changer:
PLAY: Starts playing.
4 4
4 4 : 4
Returns to the beginning of the current (or previous)
track.
¢ : ¢ ¢ ¢ ¢
Skips to the beginning of the next track.
STOP: Stops playing.
PAUSE: Pauses playing. To release it, press PLAY.
1 – 6, 7/P: Selects the number of a disc installed in a CD
player-changer.
After pressing CD (with the remote control mode selector set to
"AUDIO/TV/VCR"), you can perform the following operations on
the CD player-changer:
1 – 10, +10: Selects a track number directly.
For track number 5, press 5.
For track number 15, press +10, then 5.