Listening At Low Volume (Loudness); Attenuating The Input Signal; Adjusting The Subwoofer Output Level; Adjusting The Dsp Modes - JVC RX-888VBK Instructions Manual

Listening at Low Volume (Loudness)

(Also see page 11)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move
CONTROL," then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / fi to move
to "LOUDNESS."
4. Press @ / # to turn the
loudness "ON" or
"OFF."
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.

Attenuating the Input Signal

(Also see page 11)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move
CONTROL," then press @ / #.
The SOUND CONTROL menu appears.
3. Press % / fi to move
to "INPUT ATT."
4. Press @ / # to turn the
Input Attenuator mode
"ATT ON" or
"NORMAL."
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.

Adjusting the Subwoofer Output Level

(Also see page 11)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move
CONTROL," then press @ / #.
The SOUND CONTROL menu appears.
to "SOUND
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
LOUDNESS : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE
to "SOUND
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
LOUDNESS : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE
to "SOUND
3. Press % / fi to move
to "SUBWFR LEVEL."
4. Press @ / # to adjust
the subwoofer output
level.
5. When you finish, press EXIT repeatedly until the
menu disappears from the TV.

Adjusting the DSP Modes

(Also see pages 23 – 27)
1. Press MENU.
The MAIN MENU appears on the TV.
• Pressing one of the % / fi / @ / # buttons also displays the
MAIN MENU.
2. Press % / fi to move
3. Press @ / # to select the
DSP mode you want to
adjust.
• In this example,
"THEATER" is selected.
4. Press % / fi to move
to "SOUND
CONTROL," then
press @ / #.
The SOUND CONTROL
menu appears.
5. Press % / fi to move
to "SURROUND
LEVEL," then press
@ / #.
The SURROUND LEVEL
menu appears.
6. Press % / fi to move
set or adjust, then press @ / #.
On these adjustment menus, you can do the following:
For 3D-PHONIC
(3D ACTION, 3D DIGITAL, 3D THEATER)
"DSP EFFECT":
For DAP
(LIVE CLUB, DANCE CLUB, HALL, PAVILION)
"REAR L LEVEL": Adjust the left rear speaker output
"REAR R LEVEL": Adjust the right rear speaker output
"DSP EFFECT":
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
LOUDNESS : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:OPERATE
to "MODE."
MAIN MENU
SOURCE :VCR1
VISUAL :VCR1
MODE :THEATER
SOUND CONTROL
TUNER CONTROL
SETTING
:OPERATE
VOLUME : 20
SOUND CONTROL
SURROUND LEVEL
SEA
BAL.:R-21
LOUDNESS : OFF
INPUT ATT : NORMAL
SUBWFR LEVEL: 0dB
NEXT PAGE
:ENTER
SURROUND LEVEL
TEST TONE : OFF
CENTER LEVEL: 0dB
REAR L LEVEL: +6dB
REAR R LEVEL: 4dB
CENTER TONE : FLAT
DSP EFFECT : 3
:OPERATE
to the item you want to
Select the effect level.
level. *
level. *
Select the effect level.
:
: