Operating Jvc's Audio/Video Components; Operating Audio Components - JVC RX-8010RBK Service Manual

Operating JVC's Audio/Video Components

You can operate JVC's audio and video components with this receiver's remote control, since control signals for JVC
components are preset in the remote control.

Operating Audio Components

IMPORTANT:
To operate JVC's audio components using this remote control:
• You need to connect JVC audio components through the COMPU
LINK (SYNCHRO) jacks (see page 45) in addition to the
connections using cables with RCA pin plugs (see pages 5 and 6).
• Aim the remote control directly at the remote sensor on the
receiver.
• If you use the buttons on the front panel or the menu function to
choose a source, the remote control will not operate that source.
To operate a source with the remote control, the source must be
selected using source selecting buttons on the remote control.
• To operate the cassette deck or MD recorder using the COMPU
LINK remote control system, set the source name correctly. (See
page 16.)
• Refer also to the manuals supplied with your components.
CATV/DBS VCR 1
DVD DVD MUILTI
TV/DBS VIDEO
VCR 1 VCR 2
SURROUND DSP
ON/OFF MODE
BASS
LINE DIF .ECT BOOST
1
MIDNIGHT
MODE TEST
4
∗
SOUND SUBWFR
7/P
∗
MUTING DIGITAL EQ
10
RETURN
CATV/DBS
CONTROL CONTROL
+
∗
CH/ LEVEL
−
TV/VIDEO
MENU
TEXT /REW
DISPLAY
REC
PTY–PTY SEARCH–PTY
PAUSE
DISPLAY
MODE
A/V CONTROL RECEIVER
Note:
When you press one of the following buttons mentioned in
this section, the operation mode appears on the display
window for about 10 seconds. For example, the above
illustration shows that you have pressed CD.
Buttons
FM/AM
CD
CDR
PHONO
TAPE/MD
CONTROL (repeatedly)
SOUND
51
TV AUDIO
CD
FM/AM
CDR PHONO
TAPE/MD USB
ANALOG/DIGITAL SLEEP
INPUT
ROOM
EFFECT SIZE
2 3
MENU
CTR TONE LIVENESS
5 6
ENTER
∗ ∗
L/R BAL CENTER
8 9
∗ ∗
REAR L REAR R
0
+10
100 +
FM MODE
∗
BAL L
+ +
TV VOL VOLUME
− −
∗
BAL R
PLAY
EXIT
FF/
PAUSE
SET
STOP
CONTROL
Indications
TUNER
CD
CDR
PHONO
TAPE
VCR1 TAPE
CDDSC CDR
SOUND
Tuner
You can always perform the following operations:
FM/AM:
After pressing FM/AM, you can perform the following operations:
1 – 10, +10:
PTY SEARCH:
PTY +/ –:
DISPLAY MODE:
FM MODE:
Sound control section (Amplifier)
You can always perform the following operations:
SURROUND ON/OFF:
DSP MODE:
After pressing SOUND, you can perform the following operations:
SUBWFR then LEVEL +/ –: Adjusts the subwoofer output level.
L/R BAL then BAL L/BAL R: Adjusts the front speakers output
CENTER then LEVEL +/ –: Adjusts the center speaker output
REAR L then LEVEL +/ –:
REAR R then LEVEL +/ –: Adjusts the right rear speaker output
DIGITAL EQ then LEVEL+/ –:Selects the audio band and adjusts
EFFECT:
TEST:
CTR TONE:
ROOM SIZE:
LIVENESS:
Note:
After adjusting sounds, press the corresponding source selecting
button to operate your target source by using the 10 keys; otherwise,
the 10 keys cannot be used for operating your target source.
Alternates between FM and AM
(MW/LW).
Selects a preset channel number
directly.
For channel number 5, press 5.
For channel number 15, press +10,
then 5.
For channel number 20, press +10, then
10.
Searches for a program by PTY
codes.
Selects the PTY codes.
Shows the RDS signals.
Changes the FM reception mode.
Turns on or off the Surround modes
— Dolby Pro Logic, Dolby Digital,
and DTS Digital Surround.
Selects the DSP modes.
balance.
level.
Adjusts the left rear speaker output
level.
level.
its frequency level.
Selects the effect level.
Turns on or off the test tone output.
Selects the center tone.
Selects the room size.
Selects the liveness.