Sound Setting; Adjusting Subwoofer Level/Bass Level/Treble Level/Balance (Between Left And Right)/ Fader (Between Front And Rear)/Defeat; Audio Setup; Equalizer Presets (Factory's Eq) - Alpine CDE-148EBT Operating Instructions Manual

Sound Setting

Rotary encoder

/ENTER
AUDIO/SETUP
Adjusting Subwoofer Level/Bass Level/
Treble Level/Balance (Between Left and
Right)/Fader (Between Front and Rear)/
Defeat
1
Press AUDIO repeatedly to choose the desired mode.
Each press changes the mode as follows:
*1 *2
 BASS  TREBLE
SubW LEVEL
DEFEAT  VOLUME  SubW LEVEL
*1 When the Subwoofer mode is set to OFF, its level cannot be
adjusted, refer to "Turning Subwoofer ON/OFF" on page 16.
*2 Adjustable only when DEFEAT is OFF.
Subwoofer Level
Bass level
Treble level
Balance
Fader
Defeat
Volume
Note
• If no operation is performed for 5 seconds after selecting the Subw
LEVEL, BASS, TREBLE, BALANCE, FADER or DEFEAT mode, the
unit automatically returns to normal mode.
2
Turn the Rotary encoder until the desired sound is
obtained in each mode.
By setting DEFEAT ON, previously adjusted level settings of BASS
and TREBLE will return to the factory defaults.
Preset buttons
(1 through 6)
*2
 BALANCE  FADER 
0 ~ 15
-7 ~ 7
-7 ~ 7
–15(L) ~ 15(R)
–15(R) ~ 15(F)
ON/OFF
0 ~ 35

Audio Setup

You can flexibly customize the unit to suit your own preference and
usage. From the AUDIO SETUP menu, Audio Setting can be modified.
Use steps 1 to 5 to select one of the setting modes to modify.
See the applicable section below for details about the
selected setting item.
1
Press and hold AUDIO/SETUP for at least 2 seconds to
activate the SETUP mode.
2
Turn the Rotary encoder to select Audio, and then press
ENTER.
*1
 General  Display  Tuner  iPod&USB 
Audio
*2
Application  Bluetooth  Audio
*1 Adjustment cannot be performed during a call.
*2 Only for CDE-148EBT.
3
Turn the Rotary encoder to select the desired sound
setting menu, and then press ENTER.
*3/*4
 Parametric EQ
Factory's EQ
Subwoofer  Subwoofer Phase
*3
Power IC  MX Setup  TCR Parameter
*3 *3
 X-Over  Factory's EQ
Spatial
*3 Adjustment cannot be performed when DEFEAT is set to ON.
*4 Any changes made to either Factory's EQ or Parametric EQ are
reflected in the others' settings.
*5 In step 3, nine sound adjustment items can be selected in
Parametric EQ mode. Turn the Rotary encoder to select the
desired item, and then press ENTER to continue to step 4.
*6 These functions are inoperable when Subwoofer is set to OFF.
4
Turn the Rotary encoder to change the setting, and then
press ENTER.
5
Press and hold AUDIO/SETUP for at least 2 seconds to
return to normal mode.
Notes
• Pressing r returns to the previous Sound menu mode.
• If no operation is performed for 60 seconds, Sound menu mode is
cancelled.

Equalizer Presets (Factory's EQ)

10 typical equalizer settings are preset at the factory for a variety of
musical source material. User settings are created in the Parametric EQ
mode.
User  Flat (Initial setting) Pops  Rock  News 
Jazz&Blues  Electrical Dance  Hip Hop&Rap 
Easy Listening  Country  Classical
Note
• The Parametric EQ is used to create the Factory's EQ settings.
Adjusting the Parametric Equalizer Curve
(Parametric EQ)
You can modify the Equalizer settings to create a response curve more
appealing to your personal taste.
1
After selecting Parametric EQ from the Audio Setup mode,
turn the Rotary encoder to select the desired band, then
press ENTER.
*3/*5
 VOL LV ADJ 
*6 *6
 Subwoofer System 
*3 *3
 T.Correction 
15
-EN