Setting The Media Xpander Mode (Mx Setup); Customizing The Media Xpander Setting; Setting The Time Correction Unit (Tcr Parameter); Adjusting The Time Correction (T. Correction) - Alpine CDE-148EBT Operating Instructions Manual

OFF:
Amplifier
Amplifier
ON:
SPEAKER
RIGHT FRONT
SPEAKER
RIGHT REAR
SPEAKER
LEFT REAR
SPEAKER
LEFT FRONT
Note
• No sound is produced by the system when the Power IC is set to OFF.
Setting the Media Xpander mode
(MX Setup)
MX (Media Xpander) makes vocals or instruments sound distinct
regardless of the music source. The CD and iPod, etc. will be able to
reproduce the music clearly even in cars with a lot of road noise.
 Setting item: MX Setup
1
Turn the Rotary encoder to select the source to which you
want to apply Media Xpander, and then press ENTER.
*1
FM  CD  CMPM  USB  iPod  BT Audio
AUX
*1 Be applied for MP3/WMA/AAC files in disc.
*2 Only for CDE-148EBT.
2
Turn the Rotary encoder to select the Media Xpander
level, and then press ENTER.
OFF  Level 1  Level 2  Level 3  Customize

Customizing the Media Xpander setting

If Customize is selected in step 2, you can modify the Media Xpander to
suit your personal preference.
3
Turn the Rotary encoder to select the Band, and then
press ENTER. Band1 (Low frequencies)  Band3
(High frequencies)
Band1 (Bass)  Band2 (Mid)  Band3 (High)
4
Turn the Rotary encoder to adjust the level, and then
press ENTER.
LEVEL: 0 ~ 8
5
Note
Front
• There is no MX mode for AM radio.
Left
Front
Right
Rear
Left
You can change the unit, (cm or inch) of time correction.
Rear
Right  Setting item: TCR Parameter
Speakers
Front
Right
Rear
Right
Before performing the following procedures, refer to "About Time
Correction" on page 18.
Rear 1
Left
Front
Left
2
3
*2
 vTuner 
This function allows you to change the sound field easily.
There are three modes to choose from. For details, refer to the table
below.
Repeat steps 3 to 4 to complete the setting of other bands.
Setting the Time Correction Unit
(TCR Parameter)
Setting contents:
cm (Initial setting) / inch
cm:
Time correction value is in centimetres.
inch:
Time correction value is in inches.
Adjusting the Time Correction
(T. Correction)
After selecting T.Correction from the Audio Setup mode,
turn the Rotary encoder to select a speaker to be adjusted
and then press ENTER.
*1 *2 *3
 F-R  R-L  R-R
F-L
*1 Front-L
*2 Front -R
*3 Rear-L
*4 Rear-R
Turn the Rotary encoder to adjust the distance of the
selected speaker, and then press ENTER.
0.0 cm to 336.6 cm (3.4 cm/step)
0.0 inch to 132.7 inch (1.3 inch/step)
Note
• The total adjustment distance for all speakers should be less than 510
centimetres (201 inches).
Repeat steps 1 and 2 to set another speaker.
By setting these values to make its sound reach the listening
position at the same time as the sound of other speakers.

Adjusting the SPATIAL

Mode
OFF No effect is applied.
(Initial setting) OFF status
Creates the effect of widening the front sound
Front Wide field by delaying the sound of the front
speakers.
Creates the effect of making the front sound
Rear Wide image clear and far by delaying the sound of
the rear speakers.
*4
 SW-L  SW-R
Effect
17
-EN