Install The Door Control - Craftsman 139.53930DM Owner's Manual

iNSTALLATiON STEP 6
Irestall the Door Control
Locate door control within sight of door, at a minimum
height of 5 feet (1.5 m) where small children cannot reach,
away from moving parts of door and door hardware.
If installing into drywall, drill 5/32" holes and use the
anchors provided. For pre-wired installations (as in new
home construction), it may be mounted to a single gang
box (Figure 1).
1. Strip 7/16" (11 mm) of insulation from one end of bell
wire and connect to the two screw terminals on back of
door control by color: white wire to 2 and white/red wire
to the 1 (Figure 2).
2. Remove cover by gently prying along one side with a
screwdriver (Figure 3). Fasten with 6ABxl"
self-tapping screws (drywall installation) or 6-32x1"
machine screws (into gang box) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to protrude
above wall surface.
• Position bottom of door control on screw head and
slide down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking
plastic housing. DO NOT overtighten,
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up wall
and across ceiling to motor unit. Use insulated staples to
secure wire in several places. DO NOT pierce wire with
a staple, creating a short or open circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals as
follows: white to white and white/red to red (Figure 4).
NOTE: When connecting multiple door controls to the
opener, twist same color wires together. Insert wires into
quick-connect holes: white to white and red/white to red.
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach entrapment
warning label to wall near door control, and manual
release/safety reverse test label in a prominent location
on inside of garage door.
NOTE: DO NOT connect power and operate opener at
this time, The trolley will travel to the full open position but
will not return to the close position until the sensor beam is
connected and properly aligned,
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
• Be sure power is NOT connected BEFORE installing door
control.
• Connect ONLYto 24 VOLT low voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a closing
garage door:
• Install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.5 m), and away
from ALL moving parts of door.
• NEVERpermit children to operate or play with door control
push buttons or remote control transmitters.
• Activate door ONLYwhen it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYSkeep garage door in sight until completely closed.
NEVERpermit anyoneto cross path of closing garage door.
HARDWARE SHOWN ACTUAL SIZE
Screw 6ABxl"
Control Console (std installation)
Screw 6-32xl"
Control Console (pre-wired)
Insulated Staples
(Not shown)
Drywall Anchors
Figure 1
PRE-WlRED
INSTALLATION
24 Volt
2-Conductor
Bell Wire
Figure 2
(BACK VIEW)
weirl_ T°p
Mounting
Hole
Terminal
Screws
Bottom
Bell Mounting
Hole
Figure 3
REMOVE&
REPLACECOVER
To Replace,
Insert Top Tabs
First
To Remove,
Twist Here
r:_rlgure 4 DoorControl
Connections
I
To release or insert wire, I
push in tab with screwdriver tip
I
Strip wire 7/16" (11 mm) J
I _7/16" (11 ram) ]_.
Red White Grey
STANDARD
CONTROL CONSOLE
-- 2-Conductor
Bell Wire
Lighted
Push Button
17