Install The Door Control - Craftsman 139.53918D Owner's Manual

INSTALLATION STEP 6
Install the Door Control
Locate door control within sight of door, at a minimum height of
5 feet (1.5 m) where small children cannot reach, away from
moving parts of door and door hardware. If installing into drywall,
drill 5/32" holes and use the anchors provided. For pro-wired
installations (as in new home construction), it may be mounted to
a single gang box (Figure 2).
1. Strip 7/16" (11 mm) of insulation from one end of bell wire and
connect to the two screw terminals on back of door control by
color: white wire to 2 and white/red wire to the 1.
2. Removecover by gently prying at slot in top of the cover
with a small flat head screwdriver (Figure 1). Fastenwith
6ABxl" self-tapping screws (drywall installation) or 6-32x1"
machine screws (into gang box) as follows:
• Install bottom screw, allowing 1/8" (3 mm) to protrude above
wall surface.
• Position bottom of door control on screw head and slide
down to secure. Adjust screw for snug fit.
• Drill and install top screw with care to avoid cracking plastic
housing. DO NOT overtighten.
• Insert top tabs and snap on cover.
3. (For standard installation only) Run bell wire up wall and
across ceiling to motor unit. Use insulated staples to secure
wire in several places. Do not pierce wire with a staple,
creating a short or open circuit.
4. Strip 7/16" (11 mm) of insulation from end of bell wire.
Connect bell wire to the quick-connect terminals as follows:
white to white and white/red to red (Figure 3).
5. Position the antenna wire as shown.
6. Use tacks or staples to permanently attach entrapment warning
label to wall near door control, and manual release/safety
reversetest label in a prominent location on inside of garage
door.
NOTE:DO NOT connect power and operate opener at this time.
The trolley will travel to the furl open position but will not return
to the close position until the sensor beam is connected and
properly aligned.
To prevent possible SERIOUSINJURYor DEATHfrom
electrocution:
• DisconnectALL electric and battery power BEFORE
performing ANY service or maintenance.
• Connect ONLYto 24 VOLT low voltage wires.
To prevent possible SERIOUSINJURYor DEATHfrom a closing
garage door:
• Install door control within sight of garage door, out of reach
of children at a minimum height of 5 feet (1.5 m), and away
from ALL moving parts of door.
• NEVERpermit children to operate or play with door control
push buttons or remote controls.
• Activate door ONLYwhen it can be seen clearly, is properly
adjusted, and there are no obstructions to door travel.
• ALWAYS keep garage door in sight until completely closed.
NEVERpermit anyone to cross path of closing garage door.
HARDWARESHOWN ACTUALSIZE
_ lllllllllMIMlllllb
Insulated Staples
Screw 6ABxl" (Not shown)
(std installation)
(Gang box installation) Drywall Anchors
Figure I Figure2
REMOVE & REPLACECOVER PRE-WIRED INSTALLATION
To Replace
Insert Top
Tab___ _ _'"
Push Bar Cover I Wire
Figure 3 ,___
Door Control To release or insert wire,
Connections )ush in tab with screwdriver tip
Strip wire 7/16" (11 mm)
417/1611 (11 m m)]D.
Red White Grey
_ ,, _1+ -- +1 )Mounting
_ell II I I Hole
Wire It
I_1
'
_=_Terminal
II T-, TI I screws
It:__ Bottom
" " Mounting
(BACK VIEW) Hole
A
F Push Bar
_Wi re
Smart Control PaneP
17
0