Set Up The Auto Mode Operation For Copy, Scan, And Fax - Sharp MX-M550U Service Manual

1) Go through the modes specified in Simulation 46-20.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-4, AND PRESS START.
0. TRAY SELECT
2. EXP LEVEL
3. SPF(FRONT) 128
4. SPF(REAR) 128
5. DSPF 128
Select other than 0 - 2, and press
[START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. INPUT VALUE 0-255, AND PRESS
START.
1.SPF(FRONT)
Select 1,
Press [START] key.
and press
[START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT.
Select 0, and
press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 1-6, AND PRESS START.
(FEED TRAY)
2.TRAY1 2.TRAY2
5.BPT 6.LCC
Select 2, and
press [START] key.
SIMULATION 46-20
OC/SPF EXP. ADJUSTMENT. SELECT 3-8, AND PRESS START.
(EXP. LEVEL SELECT)
3.1.0 4.1.5
6.2.5 7.3.0
9.4.0 10.4.5
Item
0 TRAY SELECT Paper feed tray selection
1: TRAY1
2: TRAY2
3: TRAY3
4: TRAY4
5: Manual feed
6: Side LCC
1 PRINT START Print start (Default)
2 EXP LEVEL Exposure level selection
3:Exposure level1.0
4:Exposure level1.5
5:Exposure level2.0
6:Exposure level2.5
7:Exposure level3.0
8:Exposure level3.5
9:Exposure level4.0
10:Exposure level4.5
11:Exposure level5.0
3 SPF (FRONT) SPF (front)
(front frame side)
4 SPF (REAR) SPF (front)
(rear frame side)
(rear frame side)
5 DSPF DSPF (Back surface)
2) Using the mumeric keypad, select the number that corre-
sponds to the mode for which to make adjustments.
DSPF front frame side (front face copy), DSPF rear frame side
(front face copy), DSPF (back side copy) (Choose from num-
bers 3 to 5.)
3) Press the Start key.
4) Enter the density correction value using the numeric keypad.
5) Press the P or Start key.
6) Make two copies (one in original table mode and the other in
DSPF mode) and compare the copies in terms of density.
Repeat steps 4 to 6 until both copies provide the same density.
1 1. PRINT START
1
Press [SYSTEM SETTINGS] key.
128
Press [SYSTEM SETTINGS]
key, or terminate copying.
NOW PRINTING.
Press [START] key, or
press [SYSTEM SETTINGS] key.
3.TRAY3 4.TRAY4
Press [START] key, or
press [SYSTEM SETTINGS] key.
5.2.0
8.3.5
11.5.0
Setting
Content
range
–
–
–
0 – 255
MX-M700N ADJUSTMENTS 6 – 38
12-B Set up the auto mode operation for copy,
scan, and fax
This adjustment is needed in the following situations:
* U2 trouble has occurred.
1
* The MFP control PWB has been replaced.
* The EEPROM on the MFP control PWB has been replaced.
* The scanner control PWB has been replaced.
* The EEPROM on the scanner control PWB has been replaced.
1) Go through the modes specified in Simulation 46-19.
SIMULATION 46-19
EXP.MODE SETUP. SELECT 1-2, AND PRESS START.
1.AE MODE
2.AE STOP MODE(COPIER)
3.AE STOP
4.AE STOP MODE(FAX)
Select 1, and press [START] key.
SIMULATION 46-19
EXP.MODE SETUP. INPUT VALUE 1-2, AND PRESS START.
1.AE MODE
1
Select 2, 3, or 4 and
press [START] key.
SIMULATION 46-19
1
EXP.MODE SETUP. INPUT VALUE 0-1, AND PRESS START.
2.AE STOP MODE(COPIER)
Default
Mode
–
AE mode
–
–
AE fixed mode
2) Select "1 AE MODE" using the numeric keypad.
3) Press the Start key.
4) Using the numeric keypad, select the number that corresponds
to the operation spec.
128
5) Press the Start key. Pressing the Start key applies the setting.
(Auto copy mode operation setting)
1) Using the numeric keypad, select the number that corresponds
to the mode for which to make adjustments. (Choose from
numbers 2 to 4.)
2) Press the Start key.
3) Using the numeric keypad, select the number that corresponds
to the operation mode.
4) Press the Start key.
AE fix OFF: Density (exposure) is automatically controlled on a real
time basis. (The density level is dynamically changed according to
the original's pattern.)
AE fix ON: The density of the leading edge of the original is
detected and used to determine the overall density (exposure)
level. (The overall density level is fixed.)
1
1
MODE(SCANNER)0
0
Press [SYSTEM SETTINGS]
key.
Press [START] key, or press
[SYSTEM SETTINGS] key.
Set
Item
value
1 Image quality priority mode
(Normal mode)
* Gamma is sharp to
provide high contrast
images.
2 Toner consumption priority
mode
* Gamma is mild to provide
low contrast images.
0 AE fixed OFF
1 AE fixed ON
1
0
Default
2
1 (COPIER)
0 (SCANNER/
FAX)