Event Edit Procedure - Korg PA800 User Manual

Position
Position of the event, expressed in the form 'aaa.bb.ccc':
• 'aaa' is the measure
• 'bb' is the beat
• 'ccc' is the tick (each quarter beat = 384 ticks)
You can edit this parameter to move the event to a different posi-
tion. You can edit a position in either of the following ways:
(a) select the parameter, and use the TEMPO/VALUE controls
to change the value, or
(b) select the parameter, then touch it again; the numeric key-
pad will appear. Enter the new position by dialing in the
three parts of the number, separated by a dot. Zeroes at the
beginning can be omitted, as well as the least important
parts of the number. For example, to enter position
002.02.193, dial "2.2.193"; to enter position 002.04.000 dial
"2.4"; to enter position 002.01.000, simply dial "2".
Type, Value 1, Value 2
Type and values of the event shown in the display. Depending on
the selected event, the value may change. This parameter also
shows the (greyed-out, so non editable) "CC#11" (Expression)
event at the beginning of the pattern, and the "End Of Loop"
marking, when the end of a track is reached.
Event type Value 1
Note Note name
Ctrl Control Change number
Bend Bending value
To change the event type, select the Type parameter, then use the
TEMPO/VALUE controls to select a different event type. A set of
default values will be automatically assigned to the event.
To select and edit the event's value, select the corresponding
parameter, and use TEMPO/VALUE controls.
Length
Length of the selected Note event. The value format is the same
as the Position value. This is only available for Note events.
Note: If you change a length of "000.00.000" to a different value,
you can't go back to the original value. This rather uncommon
zero-length value may be found in some drum or percussion tracks.
Scrollbar
Use the scrollbar to browse the event through the list.
Other elements
Track pop-up menu
Use this pop-up menu to select the track to edit, inside the cur-
rent Chord Variation.
Drum...Acc5 Style track.
Value 2
Velocity
Control Change value
–
Style Record mode
Go Meas.
While the sequencer is not running, press this button to open
the Go to Measure dialog box:
When in this dialog box, select a target measure, and press OK.
The first event available in the target measure will be selected.
Insert
Press the Insert button in the display to insert a new event at the
current shown Position. The default values are Type = Note,
Pitch = C4, Velocity = 100, Length = 192.
Delete
Press the Delete button in the display to delete the event selected
in the display.

Event Edit procedure

Here is the general procedure to follow for the event editing.
1. Select the Style to edit, and press the RECORD button.
Select the "Current Style" option to enter recording. The
main page of the Style Record mode will appear.
2. Select the "Element (Style Element)" and "Chord Var
(Chord Variation)" parameters.
Note: For more information on the Style Elements and Chord
Variations, and the Style structure in general, see "The Style
structure" on page 106.
3. Press MENU, and select the Event Edit section. The Event
Edit page appears (see "Event Edit: Event Edit" on page 116
for more information).
4. Press START/STOP to listen to the selected Chord Varia-
tion. Press START/STOP to stop it. Chord Scanning does
not work, so you will listen the pattern at the original Key/
Chord.
5. Press the Filter tab to select the Filter page, and uncheck the
filters for the event types you wish to see in the display (see
"Event Edit: Filter" on page 118 for more information).
6. Press the Event Edit tab to go back to the Event Edit page.
7. Use the Track pop-up menu to select the track to edit (see
"Track pop-up menu" on page 117).
8. The list of events contained in the selected track (inside the
Chord Variation selected on step 2) will appear in the dis-
play. Some events on the beginning of the Chord Varia-
tions, as well as the "EndOfTrk" event (marking its ending
point) cannot be edited, therefore appearing in grey.
117
Event Edit: Event Edit