Using The Cassette Deck (Recording) - JVC RV-DP100BK Instructions Manual

Using the Cassette Deck
(Recording)
TIMER
CLOCK TIMER ON/OFF
DOWN UP SET
PROGRAM
RANDOM
AUTO
PRESET REPEAT
6
AUX CD TAPE
CD
REVERSE MODE REW MULTI CONTROL
REVERSE
MODE
DISPLAY
MID /
TREBLE
SUPER WOOFER
VOLUME
VOLUME
RM-SRVDP100E
REMOTE CONTROL
When the System is in use, the display shows other items as well.
For simplicity, we show here only the items described in this section.
Recording onto a tape from any of the sound sources is simple. Just
place a tape in the Cassette Deck, have the source ready, make one
or two settings, and you're ready to record. For each source the pro-
cedure is a little bit different so we explain each separately. But first,
here are a few things to make your recordings better.
Things To Know Before You Start
Recording —————————————
It may be unlawful to record or playback copyrighted
material without the consent of the copyright owner.
When you want to record onto both sides of a tape, you can set
Reverse mode to do so. Recording automatically stops after re-
2
cording in the reverse ( ) direction. Therefore, make sure that
the tape direction is forward (
mode on.
The recording level, which is the volume at which the new tape
is being made, is automatically set correctly, so it is not affected
by the VOLUME control on the System. Nor is it affected by
adjusting the sound effects. Thus, during recording you can ad-
just the sound you are actually listening to without affecting the
recording level.
Two small tabs on the back of the cassette tape, one for side A
and one for side B, can be removed to prevent accidental erasure
or recording.
To record on a cassette with the tabs removed, you must cover
the holes with adhesive tape first. However, when a type II tape
is used, only cover part of the hole as shown, since the other part
of the hole (Type II detection slot) is used to detect the tape
type.
Type I and Type II tapes can be used for recording.
Note: At the start and end of cassette tapes, there is leader tape
which cannot be recorded onto. Thus, before recording, wind on the
leader tape first to ensure getting the beginning of the recording.
SLEEP
PRESET
TUNER 2 3
BAND TAPE
TUNING
FM MODE
7
FF
3
) when recording with Reverse
Type II detection
slot
Adhesive tape
7
SUPER WOOFER VOLUME
VOLUME
MID / TREBLE
PRESET ONE TOUCH MID / BAND
TUNING REC TREBLE MULTI CONTROL
STANDBY
%
C D TAPE TUNER AUX
REW STOP FF
STANDBY/ON
OPEN
2 3
TAPE
ONE
TOUCH
REC
Reverse mode indicator
CAUTION: If a recording you make has excessive
noise or static, the System may have been too
close to a TV which was on during the recording.
Either turn off the TV or increase the distance be-
tween the TV and the System.
Standard Recording
You can record any sound source to tape.
The sources are CD, Tuner, auxiliary equipment, Rhythm Machine,
microphone and guitar. The microphone sound and guitar sound can
be mixed with any source. Also, you can mix the sound from the
Rhythm Machine with the CD or auxiliary equipment.
1. Insert a blank or erasable cassette tape
into the Cassette Deck.
Be sure that the Tape Direction indicator and the tape insertion
direction are as follows:
[Forward recording]
Tape Direction indicator
3
(Forward)
*Recording will be made on the tape side facing you.
• If the Tape Direction indicator
2 3
TAPE button to change the direction. (In this case, since
the tape is played, you need to press the
4
the button to rewind the tape. You may need to wind past
the leader tape which cannot be recorded onto.)
• If the inserted tape is not fully rewound, press the
rewind it. You may need to wind past the leader tape which can-
not be recorded onto.
REC indicator
Forward
Tape Direction
indicator
Reverse
Tape insertion direction
(Front view)
2
(Reverse) is lit, press the
button. Then, press
4
button to
13