One Track Recording; Cd Direct Recording - JVC RV-DP100BK Instructions Manual

2. If you want to record on both sides of the
tape, press the REVERSE MODE button on
the Remote Control to set the System in
Reverse mode.
Press the button until indicator is lit.
3. Prepare the source, by, for example, tuning
in a radio station, playing the Rhythm
Machine, or turning on the connected aux-
iliary equipment.
Note: For CD recording, refer to "CD Direct Recording" de-
scribed below.
4. Press the ONE TOUCH REC button on the
Unit.
The "REC" indicator lights up and the System starts recording.
• If the tab of the cassette tape is removed to protect erasure
or recording, recording does not start.
TIP: When you want to record in the reverse direction, you should
set the Tape Direction indicator and the cassette tape as fol-
lows in step 1. Next, start from step 3.
[Reverse recording]
Tape Direction indicator
2
(Reverse)
*Recording will be made on the opposite side tape.
To stop at any time during the recording
process, press the
button.
Recording an AM station to tape
When recording an AM broadcast, beats may be produced which
are not heard when listening to the broadcast. If this happens, press
the PRESET TUNING button on the Unit to eliminate the beats.
1. Set to AM station and start recording.
2. Press the PRESET TUNING button to eliminate the beats.
Each time you press the button, the display changes as shown
below:
= =
CUT-1 CUT-2 CUT-3
ning)

CD Direct Recording

Everything on the CD goes onto the tape in the order it is on the CD,
or according to the order you have set in a program.
1. Insert a blank or erasable cassette tape
into the Cassette Deck.
Be sure that the Tape Direction indicator and the tape insertion
direction are as follows:
(For details, refer to step 1 in "Standard Recording" on page 13.)
[Forward recording]
Tape Direction indicator
3
(Forward)
*Recording will be made on the tape side facing you.
14
Tape insertion direction
(Front view)
= =
CUT-4 (back to the begin-
Tape insertion direction
(Front view)
2. If you want to record on both sides of the
tape, press the REVERSE MODE button on
the Remote Control to set the System in
Reverse mode.
Press the button until indicator is lit.
3. Set a CD.
6
4. Press the CD button.
7
5. Press the button.
• If you want to record specific tracks only, program the
tracks first. You can check their total playback time on the
display during programming. (See page 11.)
6. Choose whether to have pauses between
recorded selections.
• If nothing is done, a non-recorded pause of about four sec-
onds will be automatically left between selections.
• If you do not want pauses between selections, do the follow-
ing before proceeding to the next step.
Press the CD 6 button twice to enter Pause mode.
7. Press the ONE TOUCH REC button on the
Unit.
The "REC" indicator lights up and the System starts recording.
• If you make a recording with Reverse mode on, the System
will record the last song at the end of the first side onto the
next side from its beginning when the song has been record-
ed more than 10 seconds on the first side.
If the last song has been recorded less than 10 seconds, then
the previous song will again be recorded on the next side as
it will not be completely recorded on the first side because
of leader tape.
• After the CD Player has played the entire CD, or all the pro-
grammed tracks, the tape automatically stops.
To stop at any time during the recording process, press the
e button. The tape stops after four seconds.
Note: When making SLEEP timer settings while doing CD Direct
recording, set enough time to allow for the CD to finish
playing, otherwise the power will go off before recording is
completed.
One Track Recording ————————
You can record the one CD track being played.
1. Insert a blank or erasable cassette tape
into the Cassette Deck.
2. Play the track on the CD you wish to
record.
3. Press the ONE TOUCH REC button on the
Unit.
The CD Player returns to the beginning of that track and the
track is recorded on the tape. After recording, the CD Player and
the Cassette Deck automatically stop.