JVC GET0602-001A Instruction Manual page 132

INSTALLATION (IN-DASH MOUNTING)
The following illustration shows a typical installation. However, you should make adjustments
corresponding to your specific car. If you have any questions or require information regarding installation
kits, consult your JVC car audio dealer or a company supplying kits.
• If you are not sure how to install this unit correctly, have it installed by a qualified technician.
Before installing the unit
• When mounting the unit, be sure to use the screws provided, as instructed. If other screws are used,
parts could become loose or damaged.
• When tightening screws or bolts, be careful not to pinch any connection cord.
• Make sure not to block the fan on the rear to maintain proper ventilation when installing the unit.
1
Remove the audio system originally installed in the car, together with its mounting brackets.
Note: Be sure to keep all the screws and parts removed from your car for future use.
2
Attach the mounting brackets (removed from the car), to this unit (see below).
3
Do the required electrical connections.
• See pages 3 – 6.
4
Install this unit using the screws removed in step
The following example is for installation in a Toyota car. For more details, consult your JVC car audio
dealer.
Mounting bracket removed from the car
從汽車拆卸的裝配架
Supplied screws
配備螺絲
Select the appropriate type fitting to your audio
system space.
選擇適合您的音響系統安裝空間的型號。
Note : When installing the unit on the mounting bracket, make sure to use the supplied screws
(M5 × 8 mm). If longer screws are used, they could damage the unit.
注意： 安裝本機進裝配架時，請務必使用配備的螺絲（M5 × 8 mm）。若使用比較長的螺絲，
有關螺絲可能會損壞本機。.
Required space for installation and the monitor ejection
安裝和顯示器退出所需的空間
20
160
1
.
Mounting bracket removed from the car
從汽車拆卸的裝配架
Dashboard
儀表盤
Unit: mm
單位：mm（毫米）
91.3
安裝（裝設、固定在儀表板內）
下面的圖解表示了典型的安裝程序。但是在實際安裝時，您應該根據您的汽車作適當的調整。如果
您有問題，或需要有關配套元件的資料，請向 JVC 汽車音響分銷商或配套元件供應公司詢問。
• 如果您不能確定如何正確地安裝本機，應請合格的技術人員來安裝。
安裝本機之前
• 當裝上本機時，必須按照指示使用配備的螺絲釘。如果使用其它的螺絲釘，相關零件可能會鬆
脫或損壞。
• 當鎖緊螺絲釘或螺栓時，切記不要壓擠到任何連接電線。
• 當安裝上後，切記不要阻擋到後面板的風扇以維持適當的通風。
1
拆卸原本安裝在汽車內的音響系統，以及其裝配架。
注意：請務必保留所有從您汽車拆卸的螺絲和零件做日後使用。
2
將 (從汽車拆卸的) 裝配架安上本機 (參閱下圖)。
3
執行必要的電路連接。
• 參閱第 3 至 6 頁。
4 1
使用在步驟 拆卸的螺絲安裝本機。
以下以豐田（Toyota）汽車安裝為例。請聯絡您的 JVC 汽車音響分銷商有關更多細節。
1
Screws removed from the car in step
1
在步驟 從汽車拆卸的螺絲
When installing the unit in a Nissan car
當安裝本機於日產汽車時
Install the unit at an angle of less than 30˚, taking it into account that the monitor would eject
when in use.
將本機安裝在少於 30˚ 的角度，您必須考慮到屏幕可以在使用時退出。
30˚
2
Supplied screws
配備螺絲
If necessary, restore the protruding tabs.
若有必要，請重新裝上凸緣。
Plate for use with a Nissan car
用於日產汽車的框