Do not use with incompatible components or alter this product in any way outside of the instructions provided by Horizon Hobby, Inc. This manual contains instructions for safety, operation and maintenance. It is essential to read and follow all the instructions and warnings in the manual, prior to assembly, setup or use, in order to operate correctly and avoid damage or serious injury.
Horizon Hobby product developers is an evolutionary level by providing multiple flight an electronic advancement that virtually eliminates assistance options. For the UMX AS3Xtra, there are common barriers RC pilots fight on a regular five pre-programmed flight modes to make complex basis.
Transmitter and Receiver Binding Binding is the process of programming the receiver to recognize the GUID (Globally Unique Identifi er) ™ code of a single specifi c transmitter. You need to ‘bind’ your chosen Spektrum DSM2/DSMX technology equipped aircraft transmitter to the receiver for proper operation. Any full range Spektrum DSM2/DSMX transmitter can bind to the DSM2/DSMX receiver.
Alternate Flight Mode Programming Out of the box, the AS3Xtra comes standard with 3 Flight Mode Benefi ts fl ight modes, shown in bold in the chart to the right. A transmitter with a 2-position channel 5 switch will Heading hold on ailerons, General only allow the use of position 0 or position 2 fl...
ESC/Receiver Arming, Battery Installation and Center of Gravity CAUTION: Always keep hands away from the propeller. When armed, the motor will turn the propeller in response to any throttle movement. Arming the ESC/receiver also occurs after binding as previously described, but subsequent connection of a fl...
Optional Side Force Generators (SFGs) Installation Side Force Generators add side force in all fl ight attitudes, increase rudder authority and make a variety of aerobatics possible. 1. Slide the SFG slot on the wing so the lower half of the SFG is under the carbon wing supports. 2.
Control Centering Before the fi rst fl ights, or in the event of an accident, make sure the fl ight control surfaces are centered. Adjust the linkages mechanically if the control surfaces are not centered. Use of the transmitter sub-trims may not correctly center the aircraft control surfaces due to the mechanical limits of linear servos.
Flying Tips and Repairs We recommend fl ying your aircraft indoors in a Repairs gymnasium, or outdoors in calm conditions. Always Repair the aircraft using foam-compatible CA avoid fl ying near houses, trees, wires and buildings. (cyanoacrylate adhesive) or clear tape. Only use You should also be careful to avoid fl...
Power Components Service Disassembly CAUTION: DO NOT handle the propeller while the fl ight battery is connected to the ESC. Personal injury could result. 1. Disconnect the battery from the ESC/receiver. 2. Hold the prop shaft using needle-nose pliers or hemostats. 3.
Troubleshooting Guide AS3X Problem Possible Cause Solution Control surfaces not at Control surfaces may not have been Center control surfaces mechanically by neutral position when mechanically centered from factory adjusting the U-bends on control linkages transmitter controls are at neutral ESC/receiver does Aircraft was not kept immobile for 5 Disconnect and reconnect the fl...
What this Warranty Covers not purchased from an authorized Horizon dealer, or (vi) Product not compliant with applicable technical Horizon Hobby, Inc. (“Horizon”) warrants to the original regulations. purchaser that the product purchased (the “Product”) will be free from defects in materials and workmanship at the OTHER THAN THE EXPRESS WARRANTY ABOVE, HORIZON date of purchase.
Page 14
Purchaser’s Remedy to obtain a RMA number along with instructions for submitting your product for service. When calling Horizon, Horizon’s sole obligation and purchaser’s sole and you will be asked to provide your complete name, street exclusive remedy shall be that Horizon will, at its option, address, email address and phone number where you can either (i) service, or (ii) replace, any Product determined be reached during business hours.
Motor 8.5mm x Brushed Motor moteur coreless ultra micro 8.5mm x 23mm 8.5mm x 23mm 8.5mmx23mm 23mm Gearbox with E-fl ite UMX AS3Xtra: Réducteur avec arbre Riduttore con albero EFLU5153 Propshaft: UMX Propellerwelle m. d’hélice elica: UMX AS3Xtra AS3Xtra Getriebe Replacement E-fl...
– Optional Parts and Accessories – – Optionale Bauteile und Zubehörteile – – Pièces optionnelles et accessoires – – Parti opzionali e accessori – Part # • Nummer Description Beschreibung Description Descrizione Numéro • Codice Hook and Loop Set Parkzone: Klettband Ultras Micros - Bande Set fascette a strappo PKZ1039...