Group:feedback Control Parameters - Toshiba TOSVERT-130 G3 Interface Manual

efesotomasyon.com -Toshiba inverter,drive,servo,plc

9.3.9 GROUP:FEEDBACK CONTROL PARAMETERS

Register Function / Title
190
FEEDBACK CONTROL
SELECTION
191 1, 2
FEEDBACK INPUT
SIGNAL
SELECTION
192
PROPORTIONAL
GAIN
193
INTEGRAL GAIN
194
ANTI-HUNTING
GAIN
195
LAG TIME
CONSTANT
196
PID LOWER LIMIT
FREQUENCY
197
PID DEVIATION LIMIT
SELECTION
198 1
PID DEVIATION
UPPER LIMIT
199
PID DEVIATION
LOWER LIMIT
19A
PG INPUT: NUMBER OF
PULSES
19B
PG INPUT: NUMBER OF
PHASES
19C
DROOPING CONTROL
ENABLE
19D 1
DROOPING
CONTROL AMOUNT
19E
OVERRIDE CONTROL
SELECTION
19F 7
OVERRIDE
MULTIPLIER
INPUT SELECTION
1A0
OVERRIDE CHANGE
MULTIPLIER
1A1 ∼
Reserved
1CF
Bank Mask
0 / 1 0060 0020: No feedback
0040: PID control
0060: Speed feedback
0 / 1 001C 0004: RR input
0008: IV input
000C: RX input
0010: PG feedback
0014: RS232C input
0018: Communication/12-bit binary
interface board
001C: BIN input
0001 ∼ 00FF (0.01 ∼ 2.55)
0 / 1 00FF
0001 ∼ 8CA0 (0.01 ∼ 360.00)
0 / 1 FFFF
0000 ∼ 00FF (0.0 ∼ 25.5)
0 / 1 00FF
0000 ∼ 00FF (0 ∼ 255)
0 / 1 00FF
0 ∼ Fmax
0 / 1 FFFF
0 / 1 0080 0000: No PID deviation limit
0080: PID deviation limited
0000 ∼ 0032 (0 ∼ 50)
0 / 1 00FF
0000 ∼ 0032 (0 ∼ 50)
0 / 1 00FF
0001 ∼ 270F (1 ∼ 9999)
0 / 1 FFFF
0 / 1 0001 0000: Single-phase input
0001: Two-phase input
0 / 1 0002 0000: OFF
0002: ON
0000 ∼ 0064 (0 ∼ 10.0)
0 / 1 00FF
0 / 1 0007 0000: OFF
0001: FCRR
0002: FCIV
0003: FCRX
0004: FCPG
0005: FCPNL
0006: FCOPT
0007: FCMLT
0 / 1 0038 0000: Reference
0008: KRR
0010: KIV
0018: KRX
0020: KBIN
FC18 ∼ 03E8 (-100.0 ∼ 100.0)
0 / 1 FFFF
 
42
Adjustment Range
(0)
(1)
(2)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(0)
(1)
(1)
(2)
(0)
(1)
(0)
(1)
(2)
(3)
(4)
(5)
(6)
(7)
(0)
(1)
(2)
(3)
(4)

Multiplier


0.01
0.01
0.1
1
0.01

1
1
1


0.1


0.1
