Mitsubishi Electric FR-D700 Instruction Manual page 196

Communication operation and setting
REMARKS
Set 65520 (HFFF0) as a parameter value "8888" and 65535 (HFFFF) as "9999".
For the instruction codes HFF, HEC and HF3, their values are held once written but cleared to zero when an inverter reset or all
clear is performed.
Example) When reading the C3 (Pr. 902) and C6 (Pr. 904) settings from the inverter of station 0
Computer Send Data
1)
ENQ 00 FF 0 01 82
2)
ENQ 00 EC 0 01 7E
3)
ENQ 00 5E 0 0F
4) ENQ 00 60 0 FB
To read/write C3 (Pr. 902) and C6 (Pr. 904) after inverter reset or parameter clear, execute from 1) again.
List of calibration parameters
Parameter
C2 (902) Terminal 2 frequency setting bias frequency
C3 (902) Terminal 2 frequency setting bias
Terminal 2 frequency setting gain
125 (903)
frequency
C4 (903) Terminal 2 frequency setting gain
C5 (904) Terminal 4 frequency setting bias frequency
C6 (904) Terminal 4 frequency setting bias
Terminal 4 frequency setting gain
126 (905)
frequency
C7 (905) Terminal 4 frequency setting gain
[Special monitor selection No.]
Refer to page 123 for details of the monitor description.
Data Description
Output frequency/speed ∗1
H01
H02 Output current
H03 Output voltage
Frequency setting/speed setting ∗1
H05
H08 Converter output voltage
H09 Regenerative brake duty
Electronic thermal relay function
H0A
load factor
H0B Output current peak value
H0C Converter output voltage peak value
H0E Output power
Input terminal status ∗2
H0F
∗1
When "0.01 to 9998" is set in Pr. 37 and "01" in instruction code HFF, the data format is 6 digits (E2).
∗2
Input terminal monitor details
b15
— — —
∗3
Output terminal monitor details
b15
— — —
192
Inverter Send Data
ACK 00
ACK 00
STX 00 0000 ETX 25
STX 00 0000 ETX 25
Instruction
Code
Name
5E DE
5E DE
5F
5F
60
60
61
61
Unit
0.01Hz/
0.001
0.01A
0.1V
0.01Hz/
0.001
0.1V
0.1%
0.1%
0.01A
0.1V
0.01kW
—
— — — —
— — — —
Description
Set "H01" to the expansion link parameter.
Set "H01" to second parameter changing.
C3 (Pr. 902) is read. 0% is read.
C6 (Pr. 904) is read. 0% is read.
1
1
DF 1
DF 1
E0 1
E0 1
E1 1
E1 1
Data
Output terminal status ∗3
H10
H14 Cumulative energization time
H17 Actual operation time
H18 Motor load factor
H19 Cumulative power
H34 PID set point
H35 PID measured value
H36 PID deviation
H3D Motor thermal load factor
H3E Inverter thermal load factor
H3F Cumulative power 2
H40 PTC thermistor resistance
— — RH
— — —
Description
RM RL — —
ABC — — —
Unit
—
1h
1h
0.1%
1kWh
0.1%
0.1%
0.1%
0.1%
0.1%
0.01kWh
0.01kΩ
b0
STR STF
b0
— RUN