Auxiliary Input; Clock Setting; Alarm Operations - Jensen JiMS-211i Owner's Manual

A UXIL IA R Y INP UT
T his unit provides an auxiliary audio signal input for
Use an audio cable with 3.5 mm stereo plug to connect the external device to the AUX IN J ack
located on the back of the unit.
C onnect the other end of the cable to a Line Out J ack or Headphone J ack of your non-dockable MP 3 player,
C D player and older, non-dockable iP ods (except 3rd gen iP od shuffle) then listen to your external source
through the speakers of this system.
1. C onnect the audio cable with 3.5 mm stereo plug to the AUX IN J ack located at rear of the unit.
2. C onnect the other end of the cable to a Line Out J ack or Headphone J ack of your external audio device.
3. T urn on the external audio device.
4. T o select auxiliary audio input, press the F UNC T ION button until the AUX indicator is displayed on the LC D.
5. T he volume level can now be controlled through the main unit. Operate all other functions on the auxiliary
device as usual.
Note:
(1) If you're connected to the Line Out J ack of your external device, then you only need to adjust the volume
control of this unit. If you're connected to the Headphone J ack of your external device, then you may need to
adjust both the volume control of your external device and the volume control of this unit to find the most
desirable volume setting.
(2) P ress the P OWE R button turning off the unit when you finish listening.
Don't forget to switch off the power of your external device as well.

CLOCK SETTING

When the unit is OFF (power off mode) :
Set Clock
1. Press the MODE button 3 times, the hour digits blink.
2. To set hour, turn the VOLUME wheel to obtain a desired value.
Note: Make sure the hour is set so that the AM or PM indicators are displayed correctly.
3. Press the MODE button again, the minute digits blink.
4. To set minute, turn the VOLUME wheel to obtain a desired value.
Set 12/24 Hour format
5. Press the MODE button repeatedly to enter 12/24 hour format setting mode, "H12" appears and flashing.
6. To select H12 (12Hour) or H24 (24 Hour) format, rotate the VOLUME wheel.
Exit setting mode
7. To save all settings and exit the setting mode, press the SNOOZE button.
connecting external audio devices.
11

ALARM OPERATIONS

Setting the Alarm time
When the unit is at the standby mode :
1. Press the MODE button once , the alarm hour digits blink.
2. To set hour, turn the VOLUME wheel to obtain a desired value.
3. Press the MODE button again , the alarm minute digits blink.
4. To set minute, turn the VOLUME wheel to obtain a desired value.
Select wake up alarm source
5. When either the alarm hour or minute digits blink, each press of the FUNCTION button allows you to
select Buzzer , iPod/iPhone or Radio as the alarm source where the corresponding indicator "Alm
"Alm iPod/iPhone" or "AlmRad" displays on screen.
Note :
- If "Wake to iPod/iPhone " is selected but your iPod/iPhone has not been docked, the alarm source
will be redirected to the Alarm Buzzer automatically when the alarm time is reached.
- When "Wake to Radio" is selected, make sure the radio staion you want to wake to is tuned.
6. To save all settings and exit the setting mode, press the SNOOZE button.
7. To activate the daily alarm, press the ALARM ON/OFF button and the corresponding alarm source indicator
appears on LCD display.
Wake to Buzzer
* When the alarm time is reached, the buzzer alarm will sound for one minute.
* It goes into Auto Snooze mode if no button has been pressed. The display shows the "SNOOZE"
indicator. The buzzer turns off for the snooze time (around 10 minutes) then comes on again.
This operation will be repeated three times. After the fourth alarm is finished, the alarm will shut
off until the same alarm time on the next day.
* You may also activate the snooze function manually after the alarm sounds by pressing the
SNOOZE button. The buzzer stops for the snooze time then comes again.
* The snooze operation (including auto snooze and manual snooze) can be repeated by 3 times only.
* To stop the alarm immediately after the buzzer sounds, you can also press the ALARM ON/OFF button.
It resets itself for the following day.
Wake to iPod/iPhone or Radio
* When the alarm time is reached, the selected alarm source (iPod/iPhone or Radio) will automatically turn on.
It starts softly and gradually becomes louder.
* It plays for 60 minutes then shuts off and resets itself for the following day.
* During the activation of the alarm source, you may press the SNOOZE button to activate the
snooze function. The alarm stops for the snooze time (around 10 minutes) then turns on again.
This manual snooze operation can be repeated three times. Each time the alarm turns on, it plays
for 60 minutes (without pressing the snooze button).
* To stop the alarm immediately after the alarm sounds, you may also press the ALARM button.
It resets itself for the following day.
Note :
- For the alarm source iPod/iPhone is selected and the corresponding device has not been docked
in the station. When the alarm comes, it will redirect to "Wake to Buzzer" automatically.
12
",