Potterton Paramount 40 Installation, Operation & Maintenance Manual page 23

POTTERTON COMMERCIAL PRODUCTS DIVISION
INSTALLATION, OPERATION AND MAINTENANCE MANUAL
PARAMOUNT
Display on room control module RRG
Program BUM parameter final
user level
No.
700 Stoer1
701 StrPn1
702 StrDial
703/706 Stoer2/Stoer3
709/712 Stoer4/Stoer5
710/707 StrPn2/StrPn3
710/713 StrPn4/StrPn5
705/708 StrDia2/StrDia3
711/714 StrDia4.StrDia5
715 Stoer_ akt
716 StrPn_akt
717 StrDia_akt
718 BetrStd
719 BetrStdHz
720 BetrStdBw
721 BetrStdZone
722 InbetrSetz
723 Pmittel
724 MmiStatus
725 OT_SwVersLMU
755 IonStrom
Other parameters displayed are not relevant for operation of PARAMOUNT!
*) Note : Any new settings to be recorded in manual
1) These parameters should be altered to suit the specific heating system for optimum comfort and performance.
2) These parameters should be adjusted only when absolutely necessary
3) These parameters should never be adjusted
4) For a list of the internal software diagnosis codes, see RRG manual of the Service Module for a selection of the fault codes see table 6
5) Parameters only valid if the boiler is equipped with a PWM pump (modulating pump) (Not Potterton supply)
The PARAMOUNT boilers are factory-preset to a single step pump (Parameter 561.0 OFF).
EXPLANATIONS ON ADJUSTMENT TABLE FOR
HEATING ENGINEERS
Explanations of heating engineer level: The
PARAMOUNT boiler is factory-set for operation and
requires no changes as a rule.
However, a few parameters (see
table for heating engineer serve for adaptation to the
specific heating system and should be altered to suit
the specific heating system for optimum comfort and
performance.
Note: The parameters marked with
readjusted in exceptional cases when absolutely
necessary.
Explanations on Table 6: A room control module
RRG or service module RRG (optional extra) is
required for adjusting the parameters.
505 (TkSnorm) (modulating pump only): NOT
REQUIRED U.K.
510 (TuebBw) Boiler temperature setting increase
for hot water charging: This ensures efficient hot-
water charging. The boiler temperature setting is
increased when hot water is required.
Quicker charging
Reduction: Slower charging time; less overshoot.
st
1 history value for fault code counter
st
1 history value for fault phase
st
1 history value for SE diagnostic code b0
nd rd th th
2 /3 /4 and 5
fault code counter
nd th
2 /34d/4 and 5
fault phase
nd rd th th
2 /3 /4 and 5
diagnostic code b0
Current value of fault code counter
Current value of fault phase
Current value of internal SW diagnostic code b0
Burner operating time
Heating mode operating time
Hot-water mode operating time
Zone operating time
Start-up counter
Average boiler output
Current summer/winter setting for boiler module
Parameter level
Display of actual ionisation current value
1
) in the adjustment
2
) should only be
Increase
time; greater overshoot.
Function
history value for
th
history value for
history value for SW
514 (TuebVor)
increase for VT heating circuit: Increasing the flow
temperature
temperature. Increasing: Variable flow temperature
undershoot is avoided. Lowering: Variable flow
temperature undershoot possible.
516 (THK) Summer/Winter – Changeover Temp:
The automatic S/W changeover is a function with a
long-term effect which switches off the heating during
the summer when the outdoor temperature is higher
than the S/W changeover temperature, and switches
it back on only when the outdoor temperature is
below the value set here for a longer period of time.
S/W changeover via 2 methods:
- By pressing button on heating circuit module HKM
(Fig 7)
- With
temperature.
When operated with the room control module RRG,
this module takes over automatic S/W changeover
for the appropriate heating circuits (See RRG
Manual).
When operated with the heating circuit module HKM
and other
automatic
No. 516) is effective.
Basic Setting
(set at factory)
4)
Display
4)
Display
4)
Display
4)
Display
4)
Display
4)
Display
4)
Display
4)
Display
4)
Display
Display (h)
Display (h)
Display (h)
Display (h)
Display (h)
Display (kW)
Display
Display
Display
Boiler temperature
achieves a constant
automatic S/W changeover
EUROCONTROL
S/W changeover
SECTION 5
PAGE 21
New
Settings *)
setting
Variable flow
via outdoor
controllers, the
feature (program