Related Manuals for Jacuzzi J - 2 0
Summary of Contents for Jacuzzi J - 2 0
- Page 1 J - 2 0 0 ™ s e r i e s J - 280 J - 270 J - 230 J - 210 2530-277u rev. C...
- Page 2 Attention New Spa Owner! Congratulations on the purchase of your new Jacuzzi is a list of automated functions performed by your spa. These functions are listed below in an attempt to alleviate any operational concerns you may have during the first 24-hours of ownership! Also listed below are important maintenance recommendations you should observe on a regular basis to protect your new investment.
-
Page 3: Table Of Contents
Selecting The Filtration/Heating Mode... 29 11.6 Filtration Modes for Spas Without Circulation Pump Option (All Models) ... 29 11.7 Filtration Modes for Spas With Circulation Pump Option (J-230, J-270 and J-280 Only) ... 30 © 2009 Jacuzzi Hot Tubs, Inc. All Rights Reserved... - Page 4 12.0 Spa Maintenance ... 32 12.1 Cleaning The Filters... 32 12.2 Draining and Refilling... 35 12.3 Pillow Care... 35 12.4 Cleaning The Spa Interior ... 36 12.5 Maintaining the Cover ... 36 12.6 Maintaining The Synthetic Cabinet ... 36 12.7 Winterizing ... 36 12.8 Restarting Your Spa in Cold Weather ...
-
Page 5: Important Spa Owner Information
Jacuzzi premium insulating cover in place at all times when the spa is not in use. Read and carefully follow the requirements for your spa’s support base found in section 4.0 titled, “Choosing A Location”... -
Page 6: Important Safety Instructions For All Spa Owners
J-200 Series Important safety Instructions for all spa owners reaD anD Follow all InsTruCTIons CareFullY! This spa was manufactured to meet the standards and specifications outlined in the “Virginia Graeme Baker Pool and Spa Safety Act” (VGB Safety Act). When installing and using this spa, basic safety precautions should always be followed, including: DanGer: •... - Page 7 The disconnecting means must be readily accessible and visible to the spa occupant but installed at least 5 feet (1.5m), from the spa. • The electrical circuit supplied for the hot tub must include a suitable ground fault circuit interrupter (GFCI) as required by NEC Article 680-42. warnInG: •...
- Page 8 J-200 Series warnInG: • Since excessive water temperatures have a high potential for causing fetal damage during the early months of pregnancy, if pregnant or possibly pregnant, consult your physician before using a spa. • Pregnant or possibly pregnant women should limit spa water temperatures to 100°F (38°C).
- Page 9 To ensure you have a safe and enjoyable hot tub experience, learn all you can about hot tub safety and emergency procedures. Especially useful are the brochures listed below: •...
-
Page 10: Entrapment Risk
J-200 Series entrapment risk The Consumer Products Safety Commission/USA has reported that users of pools and spas have become entrapped (stuck) to drain and/or suction fittings causing death, drowning, or serious injury (see diagram below). This spa was manufactured to meet the standards and specifica- tions outlined in the “Virginia Graeme Baker Pool and Spa Safety Act”... -
Page 11: Hyperthermia
For additional or replacement Warning Signs please contact your local Jacuzzi dealer and reference item number #6530-082. rIsk oF severe InJurY or DrownInG! rIsk oF severe InJurY or DrownInG! -
Page 12: Important Csa Safety Instructions (Canada Only)
It contains the most advanced safety and self-protective equipment in the industry. Nonetheless, this spa must be installed properly to ensure dependable usage. Please contact your local Jacuzzi dealer or local building department should you have any questions regarding your installation. -
Page 13: Choosing A Location
Choosing a location ImporTanT: Because of the combined weight of the spa, water and users, it is extremely important that the base upon which the spa rests be smooth, flat, level and capable of uniformly supporting this weight, without shifting or settling, for the entire time the spa is in place. If the spa is placed on a surface which does not meet these requirements, damage to the skirt and/or the spa shell may result. -
Page 14: Outdoor Location
J-200 Series outdoor location In selecting the ideal outdoor location for your spa, we suggest that you take into consideration: • The proximity to changing area and shelter (especially in colder weather). • The pathway to and from your spa (this should be free of debris so that dirt and leaves are not easily tracked into the spa). - Page 15 Consult a licensed architect or building contractor to determine your specific needs if installing your hot tub indoors. In the unlikely event that you should ever need In addition to maintenance of filters and water...
-
Page 16: General Electrical Safety Instructions
Please contact your dealer or local building department should you have any questions regarding your installation. Proper grounding is extremely important. Jacuzzi spas are equipped with a current collector system. A pressure wire connector is provided on the... -
Page 17: Power Requirements
Refer to pages 44-47 for circuit board configuration details or contact your authorized Jacuzzi dealer. all north american J-270 and J-280 models (60 Hz) Circuit Breaker (2-Pole):... - Page 18 J-200 Series all north american J-210 Convertible Models (60 hz) Circuit Breaker: Number of Wires: Frequency: Current Draw: * all Canadian spas must be hard wired per Csa Canadian standards. (page 8) † In 15A/30A configuration, the heater will not operate while the jets pump is running in high speed.
- Page 19 export J-210 and J-230 models (50 Hz) Circuit Breaker: Number of Wires: Frequency: Current Draw: In 20A configuration, the heater will not operate while the jets pump is running in high speed. This is the factory setting ** In 30A configuration, the heater will operate while the jets pump is running in high speed.
-
Page 20: Electrical Wiring Instructions
J-200 Series electrical wiring Instructions ImporTanT noTICe: The electrical wiring of this spa must meet the requirements of the National Electrical Code/USA (NEC) and any applicable state or local codes. The electrical circuit must be installed by a qualified electrician and approved by a local building/electrical inspection authority. - Page 21 Then remove the four control box door screws and door (Figure B). 8. Select the power supply inlet you want to use (Figure A). Feed power cable to control box, then install it through the large opening provided in the bottom side of the box. 9.
- Page 22 240 VAC, 3-Wire Connection 60 Hz Congratulations! You are now all set to get your new spa ready to use. Simply follow the step-by-step procedure in Section 8.0, before long, you will be enjoying your first glorious experience in your Jacuzzi J-200 Series spa. Figure-D...
-
Page 23: Spa Fill Up Procedure
“hard”, it is preferable to fill half-way with hard water and the rest of the way with softened water. You may fill entirely with hard water if you use a special water additive available from your Jacuzzi dealer. warnInG: •... - Page 24 J-200 Series warnInG: Never leave chemicals opened and accessible to anyone. Use chemicals according to the vendors instructions. Always store chemicals in a safe and/or locked location. Keep away from and out of reach of children. 6. establish a stable sanitizer reading Establish a stable sanitizer reading between 3.0-4.0 ppm chlorine or 2.0- 4.0 ppm bromine.
- Page 25 Never add chlorine tablets (trichlor) or acid to your hot tub for any reason! These chemical may damage components within your hot tub, burn or irritate your skin, create a rash, and void the manufacturer warranty for your spa. water Fill volume by Model...
- Page 26 “hard”, it is preferable to fill half-way with hard water and the rest of the way with softened water. You may fill entirely with hard water if you use a special water additive available from your Jacuzzi dealer. 13. Consult your authorized Jacuzzi dealer for chemical...
- Page 27 • To decrease the risk of injury, entrapment or drowning, never leave your hot tub unattended for any reason, especially if while the cover is open and accessible to small children and animals! • To decrease the risk of (e.g.
-
Page 28: Control Functions
J-200 Series Control Functions Control panel A. leD Display: Can display current water temperature (de- fault display), water temperature set point, selected filtration/ heating mode, and error messages. B. Heat Indicator: Lit when heater is on. C. Jets 1 Button: Turns jets pump #1 on and off. Press once for low speed;... -
Page 29: General Spa Features And Controls
General spa Features and Controls J-280 model illustrated - Jet locations and features will vary by model. Control Panel Headrest Pillows (4 ea.) Air Controls (4 ea.) Cup Holders (4 ea.) Massage Selector (1 ea.) Lighting System Options: • Standard Underwater light system includes incandescent light (6a) •... -
Page 30: Operating Instructions
J-200 Series 10.0 operating Instructions The spa control system has automatic functions that operate upon start-up and normal operation to protect the system. Upon power up, the readout displays the following information: 1. Control panel displays current software release (3.56 or 5.56 depending on spa model) then;... -
Page 31: Optional Multi-Colored Led Light System Operation
10.4 optional multi-Colored leD light system operation The multi-colored LED spa light offers seven constant color variations and three unique random modes for enhanced spa enjoyment. Press the Light button once to activate the first light mode Random Fade, then continue pressing the button to either turn the light off or to select one of seven constant colors, random solid color mode or strobe mode as illustrated below. -
Page 32: Air Controls
J-200 Series 10.7 air Controls Certain jet systems have their own air control. Each control introduces air into the water lines that supply that specific jet group. Simply turn the air control of choice counterclockwise to open or clockwise to close. To minimize heat loss, all air controls should be closed when the spa is not in use. -
Page 33: Economy Filtration/Heating Modes (All Models)
11.3 economy Filtration/heating Modes (all Models) Economy filtration/heating modes (F4-F6) are typically selected by customers in warm climates where heat up times are minimized due to higher ambient temperatures. In either of these modes, the water temperature is regulated by the set temperature, low-speed pump or optional circulation pump, and heater only while a programmed filtration/ heating cycle is running. -
Page 34: Filtration Modes For Spas With Circulation Pump Option (J-230, J-270 And J-280 Only)
J-200 Series lock modes (l1-l2) Lock Out (disables all spa functions to permit filter cleaning) Lock Mode (disables the jets and light buttons to prevent unauthorized use of spa). Filtration/heating cycle will continue to operate as programmed in this mode. The temperature display flashes when this function is enabled. - Page 35 lock modes (l1-l2) Lock Out (disables all spa functions to permit filter cleaning). Lock Mode (disables the jets and light buttons to prevent unauthorized use of spa). Filtration/heating cycle will continue to operate as programmed in this mode. The temperature display flashes when this function is enable.
-
Page 36: Spa Maintenance
12.0 spa maintenance Proper and regular maintenance of your spa will help it retain its beauty and performance. Your authorized Jacuzzi dealer can supply you with all the information, supplies, and accessory products you will need to accomplish this. DanGer: rIsk oF severe InJurY or DrownInG BY enTrapmenT! •... - Page 37 To ensure optimum performance, clean and reuse the skimmer bag and filter cartridge once a month or as necessary, depending on use. J-210 models include filters on their footwell suction covers (shown right) that prevent debris from entering the pump and the massage selector(s), when operating.
- Page 38 “F”, followed by soaking the filter overnight in a plastic container filled with a solution of water and specially formulated filter cleanser available from your authorized Jacuzzi dealer. The average life expectancy of each filter is approximately two years with proper care and water quality maintenance.
-
Page 39: Draining And Refilling
12.2 Draining and refilling About every 3 months, you will want to replace the spa’s water. The frequency depends on a number of variables including the amount of use, attention paid to water quality maintenance, etc. You will know it is time for a change when you cannot control sudsing and/or you can no longer get the normal feel or sparkle to the water even though the key water balance measurements are all within the proper parameters. -
Page 40: Cleaning The Spa Interior
12.5 maintaining the Cover Using the Jacuzzi insulating spa cover anytime the spa is not in use will significantly reduce your operating costs, heat-up time and maintenance requirements. To prolong the life of the cover, handle it with care and clean it regularly using mild soap and water. -
Page 41: Restarting Your Spa In Cold Weather
Replace the drain plugs. 5. Re-install synthetic cabinet side panel and cover spa so that no casual moisture can enter into it. Consult your authorized Jacuzzi dealer if you have any questions regarding winter use or winterizing. 12.8... -
Page 42: Ph Control
Some are necessary to compensate for out-of-balance water, some aid in cosmetic water treatment and others simply alter the feel or smell of the water. Your authorized Jacuzzi dealer can advise you on the use of these additives. When adding spa shock (chlorine or non-chlorine) or pH balancing chemicals activate the jets pump(s) and leave the spa cover open for a minimum of 20 minutes. -
Page 43: Optional Cd Ozone Water Maintenance System
13.3 optional CD ozone water maintenance system If you have elected to have your spa equipped with the optional Jacuzzi CD ozone water purification system you will find that your water stays fresh and clear with significantly less chemical sanitizer usage. You will also probably be able to go longer between complete spa drainings. -
Page 44: Panel Displays Ice
14.4 panel Displays sn1 Open sensor (heater is disabled) or shorted sensor (spa is deactivated). The high-limit temperature sensor is not functioning. Contact your authorized Jacuzzi dealer or qualified service technician. 14.5 panel Displays sn2 Open or shorted sensor (heater disabled). The temperature sensor is not functioning. -
Page 45: Panel Displays Oh
Water temperature has reached 112˚F (44˚C) and the low speed jets pump 1 and optional circulation pump (when equipped) has activated to circulate water through heater. Contact your authorized Jacuzzi dealer or qualified service technician. 14.9 panel Displays (- - -) -
Page 46: Troubleshooting Procedures
Components operate (e.g. Pump, light) Check the following: Is there power to the spa? Is the household circuit breaker tripped? Contact your authorized Jacuzzi dealer or qualified service technician. 15.2 pump Does not operate But light Does... -
Page 47: No Heat
Nonetheless, we are always striving to improve the quality and features of our products. Your input as a Jacuzzi spa owner is a cherished part of this process. If you have any comments or suggestions, or if you wish to be informed on any new products for your spa, please write to us. -
Page 48: Circuit Board Diagrams
J-200 Series 16.0 Circuit Board Diagrams 16.1 north american J-230, J-270 and J-280 Models This wiring diagram is used for all J-230, J-270 and J-280 240V 60 Hz North American spa models With or Without the Circulation Pump Option. -
Page 49: North American J-210 Convertible Models
Wire size must be appropriate per NEC and/or local codes. 4. If hot tub is to be operated on 30A service, make sure the jumper provided at location JP1 #1&2 on the circuit board is installed. If hot tub is to be operated on 40A service, remove the jumper JP1 #1&2 on the circuit board. -
Page 50: Export 50 Hz J-230, J-270 And J-280 Models
J-200 Series 16.3 export 50 hz J-230, J-270 and J-280 Models This wiring diagram is used for all J-230, J-270 and J-280 230V 50 Hz Export spa models With or Without the Circulation Pump Option. -
Page 51: Export 50 Hz J-210 Models
16.4 export 50 Hz J-210 models This wiring diagram is used for all J-210 230V 50 Hz Export spa models. J1 Logic Jumper Settings JP1 1-2 ON = 20A Logic (Factory Setting) JP1 1-2 OFF = 30A Logic JP1 7-8 ON = °C Temperature Display (Factory Setting) JP1 7-8 OFF = °F Temperature Display Spa Light... -
Page 52: Optional Stereo Receiver Functions
J-200 Series 17.0 optional stereo receiver Functions J-230, J-270 and J-280 Models only: To start enjoying your new stereo receiver, please read the following operation instructions in their entirety. 1. power Button: Press PWR (Power) to turn deck on or off. 2. - Page 53 automatically scan and store station presets, simply press and hold A/PS for several seconds, then release. 6. DIsp Button: Press DISP to switch between clock and station frequency. When selected, the clock will display for 5 seconds then automatically revert back to station frequency. 7.
- Page 54 J-200 Series 13. Preset 4/rDM button: In tuner mode, any station can be stored as preset 4 by simply pressing and holding this button for several seconds. To recall the station preset, simply press and release this button. In CD mode press this button to randomly play song tracks. Press again to turn off this feature.
- Page 55 19. eject Button (not Illustrated): To eject CD, press OPEN and flip- down the front access panel, then press the Eject button located to the left of CD slot. 20. usa/europe switch (not illustrated): You can switch between American (USA) and European radio frequency bands by flipping a switch located on the bottom of the deck.
- Page 56 J-200 Series 24. Playback order of the MP3 File: • A directory that does not include an MP3 file is skipped. • We recommend that you make no more than two levels for each disc. • Maximum number of folders: 256 •...
- Page 57 J-200 Series...
- Page 58 J-200 Series serial number: ___________________________ model name: Dealer name: notes: __________________________________ _________________________________________ _________________________________________ _________________________________________ ___________________________ ___________________________...
- Page 59 J-200 Series...
- Page 60 J-200 Series...