Related Manuals for Jonsered FR2115MA
Summary of Contents for Jonsered FR2115MA
- Page 1 Operator's Manual Please read these instructions carefully and make sure you understand them before using the machine.
- Page 2 Svenska –...
-
Page 3: Table Of Contents
TABLE OF CONTENTS Operator’s manual for FR 2111, FR 2113 A, FR 2113 MA, FR 2115 MA Introduction ............2 Replacing the fuel filter FR 2115 ....27 Driving and transport on public roads ....2 Replacing the air filter FR 2111, FR 2113 ..28 Towing .............. -
Page 4: Introduction
INTRODUCTION Congratulations Thank you for purchasing a Front Rider. Front Riders have been designed according to a unique concept with a front mounted mowing deck and patented rear wheel steering. The machine is built to give maximum efficiency even in small and confined areas. Collected controls and a hydrostatic transmission controlled by pedals(some models) also contribute to the machine’s performance. -
Page 5: Serial Number
INTRODUCTION Good service Jonsered’s products are sold all over the world and only in specialised retail trade with complete service. This ensures that you as a customer receive only the best support and service. Before the machine is delivered it undergoes inspection and is adjusted by your dealer. -
Page 6: Explanation Of Symbols
EXPLANATION OF SYMBOLS These symbols can be found on the Rider and in the operator’s manual. Study them carefully so you understand their significance. Read the operator’s manual. Reverse Neutral Fast Slow Engine off Battery Choke Fuel Oil level Cutting height Reversing Forward Ignition... -
Page 7: Safety Instructions
SAFETY INSTRUCTIONS Safety instructions These instructions are for your safety. Read them carefully. WARNING! The inserted symbol means that important safety instructions need to be observed. It applies to your safety. General use • Read all the instructions in this operator’s manual and on the machine before you start it. - Page 8 SAFETY INSTRUCTIONS • Take care when rounding a fixed object, so that WARNING! the blades do not hit it. Never run the machine Engine exhaust, some of its over foreign objects. constituents and certain vehicle components contain or emit • Only use the machine in daylight or in other chemicals considered to cause well-lit conditions.
-
Page 9: Driving On Slopes
SAFETY INSTRUCTIONS Driving on slopes Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is the greatest; this can result in serious injury or death. All slopes demand extra care. -
Page 10: Children
SAFETY INSTRUCTIONS Children • Serious accidents may occur if you fail to be on your guard for children in the vicinity of the machine. Children are often attracted to the machine and mowing. Never assume that children will remain where you last saw them. •... - Page 11 SAFETY INSTRUCTIONS • If leaks arise in the fuel system, the engine must not be started until the problem has been resolved. WARNING! • Store the machine and fuel in such a way that The engine, and components of there is no risk that leaking fuel or fumes can the exhaust and hydraulic cause any damage.
-
Page 12: Transport
SAFETY INSTRUCTIONS • Never use the machine indoors or in spaces lacking proper ventilation. Exhaust fumes contain carbon monoxide, an odourless, poisonous and highly dangerous gas. • Stop and inspect the equipment if you run over or into anything. If necessary, make repairs before starting. -
Page 13: Presentation
PRESENTATION Presentation Congratulations on your choice of an exceptionally On FR 2113 and FR 2115 transmission is by means high quality product. of a variable speed hydrostatic gearbox. Four models equipped with engines from Briggs & FR 2113 is available in two versions. FR 2113 A has Stratton are described in this operator’s manual. -
Page 14: Throttle/Choke Control Fr 2111
PRESENTATION FR 2111 Throttle and Choke controls The throttle is used to control the speed of the engine and thereby also the rotation speed of the blades. The control is also used to activate the choke. When the choke is engaged a richer fuel/air mixture is fed to the engine, which facilitates starting in the cold. -
Page 15: Throttle/Choke Control Fr 2113, Fr 2115
PRESENTATION FR 2113, FR 2115 Throttle and Choke controls The throttle is used to control the speed of the engine and thereby also the rotation speed of the blades. The control is also used to activate the choke. When the choke is engaged a richer fuel/air mixture is fed to the engine, which facilitates starting in the cold. -
Page 16: Mowing Deck
PRESENTATION Mowing deck FR 2111 and FR 2113 A have a triple blade mowing deck with rear ejection, i.e. the clippings are thrown out behind the mowing deck. 8009-260 FR 2113 MA has a double blade Mulching unit and FR 2115 MA has a triple blade Mulching unit. 8009-261 Lifting lever for the mowing deck The lifting lever is used to put the mowing deck in... -
Page 17: Lever To Adjust The Cutting Height
PRESENTATION Lever to adjust the cutting height Using the lever the cutting height can be adjusted in 9 different positions. Deck with rear ejection, 40-90 mm (1 9/16" - 3 9/16") Mulching unit, 45-95 mm (1 3/4" - 3 3/4") 8009-251 Seat The seat has a hinged mounting on the front edge... -
Page 18: Driving
DRIVING IMPORTANT INFORMATION The air intake grille in the engine cover behind the driver’s seat must not be blocked by, for example, clothing, leaves, grass or dirt. Impaired cooling of the engine. Risk of major engine damage. Before starting 8009-430 •... - Page 19 DRIVING With a cold engine: 4. Move the throttle to position 3 (choke position). In this position the engine is fed with a richer mixture, which means the engine is easier to start. 8009-254 With a warm engine: 5. Move the throttle in between positions 1 and 2. 8009-255 6.
-
Page 20: Driving The Rider
DRIVING 7. Once the engine has started release the ignition key back to the neutral position. Move the throttle to the required engine speed. When mowing 3/4 to full throttle. STOP START WARNING! Never run the engine indoors, in enclosed or badly ventilated areas. -
Page 21: Mowing Tips
DRIVING 3. Select the required cutting height (1-9) using the cutting height lever. In order to obtain an equal cutting height, it is important that the air pressure is the same in both front wheels (60 kPa/8.5 PSI). 8009-251 4. Press in the lock button on the lifting lever and lower the mowing deck. -
Page 22: Stopping The Engine
DRIVING WARNING! Do not use the Rider on ground that slopes more than 15°. Mow upwards and downwards on slopes, never sideways. Avoid sudden changes in direction. Starting on slopes, manual gearbox 1. Press down the parking brake MAX 15° 2. -
Page 23: Maintenance
MAINTENANCE Maintenance schedule The following is a list of maintenance procedures that must be performed on the Rider. For those points not described in this manual, visit an authorised service workshop. Maintenance Daily interval hours maintenance Maintenance Page before starting Check the engine oil level on FR 2111, FR 2113 Check the engine oil level on FR 2115 Check the engine’s cooling air intake... -
Page 24: Dismantling The Rider Covers
MAINTENANCE Dismantling the Rider covers Engine cover The engine becomes accessible for service when the engine cover is folded up. Fold the seat forward, loosen the rubber strap under seat and fold the cover backwards. 8009-262 Front cover FR 2111, FR 2113 A Remove the bolts holding the front cover (3) and lift off the cover. - Page 25 MAINTENANCE Right-hand wing cover Remove the bolts holding the wing cover (2 and 3). On FR 2113 and FR 2115 the knob (1) should also be removed. 8009-265 Left-hand wing cover Remove the bolts holding the wing cover and lift off the cover.
-
Page 26: Checking And Adjusting The Steering Wires
MAINTENANCE Checking and adjusting the steering wires The steering is governed by means of wires. After a period of use these can become stretched, which means the steering setting may have changed. The steering is checked and adjusted as follows: 1. -
Page 27: Checking And Adjusting The Brake
MAINTENANCE Checking the brake FR 2111 The brake is a disc brake and is located on the gearbox. Check that the brake is adjusted correctly by measuring the distance between the brake lever and front edge of the cut-out on the chassis. The distance should be 0-1 mm (0-0.040") when the brake is not actuated. -
Page 28: Adjusting The Throttle Cable Fr 2111, Fr 2113
MAINTENANCE FR 2111, FR 2113 Adjusting the throttle cable The throttle cable may need to be adjusted, if the engine does not respond as it should when accelerating, if it produces black smoke or maximum revs are not reached. 1. Loosen the clamping screw (by the arrow), and slide the throttle to the choke position. -
Page 29: Adjusting The Throttle Cable Fr 2115
MAINTENANCE FR 2115 Adjusting the throttle cable The throttle cable may need to be adjusted, if the engine does not respond as it should when accelerating, if it produces black smoke or maximum revs are not reached. 1. Loosen the clamping screw (by the arrow), and slide the throttle to the choke position. -
Page 30: Replacing The Air Filter Fr 2111, Fr 2113
MAINTENANCE FR 2111, FR 2113 Replacing the air filter If the engine seems weak or runs unevenly, the air filter may be clogged. For this reason, it is important to replace the air filter regularly (see the chapter Maintenance/ Maintenance schedule for the proper service interval). -
Page 31: Replacing The Air Filter Fr 2115
MAINTENANCE FR 2115 Replacing the air filter If the engine seems to lack power or goes irregu- larly the reason may be that the air filter is clogged. It is therefore important to replace the air filter at regular intervals (see ”Maintenance schedule” for correct service interval). -
Page 32: Checking The Fuel Pump's Air Filter
MAINTENANCE Checking the fuel pump’s air filter Check regularly that the fuel pump’s air filter is not clogged by dirt. The filter can be cleaned using a brush, if neces- sary. Checking the acid level in the battery Check that the acid level in the battery lies between the markings. -
Page 33: Checking The Safety System Fr 2111
MAINTENANCE FR 2111 Checking the safety system The Rider is equipped with a safety system that prevents starting or driving under the following conditions. The engine should only be possible to start when the mowing deck is in its raised position and the Starter Works gear shift lever or hydrostat pedals are in the... -
Page 34: Checking The Safety System Fr 2113
MAINTENANCE FR 2113, FR 2115 Checking the safety system The Rider is equipped with a safety system that prevents starting or driving under the following conditions. The engine should only be possible to start when the mowing deck is in its raised position and the Starter Works gear shift lever or hydrostat pedals are in the... -
Page 35: Main Fuse
MAINTENANCE Main fuse The fuse is located in a loose holder under the battery case cover, in front of the battery. Type: Flat-blade mounting, 15 A. Do not use any other type of fuse when replacing. A blown fuse indicates that the mounting has burnt off. -
Page 36: Checking And Adjusting The Mowing Deck's Ground Pressure
MAINTENANCE Checking and adjusting the mowing deck’s ground pressure on FR 2113 MA and FR 2115 MA In order to achieve the best mowing result the mowing deck should follow the ground without touching it too heavily. The pressure is adjusted using a screw on each side of the Rider. -
Page 37: Adjusting The Parallelism Of The Mowing
MAINTENANCE FR 2111, FR 2113 MA Adjusting the parallelism of the mowing deck on FR 2111 1. Check that the tyres’ air pressure is 60 kPa (0.6 kp/cm /8.5 PSI). 2. Dismantle the front cover and the right-hand wing cover as described on pages 22-23. 3. -
Page 38: Deck Fr 2115 Ma
MAINTENANCE FR 2115 MA Adjusting the parallelism of the mowing deck on FR 2115 MA 1. Check that the tyres’ air pressure is 60 kPa (0.6 kp/cm /8.5 PSI). 2. Remove the front cover and the right-hand wing cover. 3. Loosen the parallelism stay’s nuts. 4. -
Page 39: Service Position For The Mowing Deck
MAINTENANCE FR 2113 MA, FR 2115 MA The mowing deck’s service position In order to provide good accessibility for cleaning, repair and servicing, the mowing deck can be set in the service position. The service position means that the mowing deck is raised and locked in the vertical position. - Page 40 MAINTENANCE FR 2113 MA, FR 2115 MA 4. Fit the two support wheels on each side of the mowing deck’s rear section. WARNING! Wear protective glasses when dismantling the mowing deck. The spring that tension the belt can fly off and cause personal injury.
-
Page 41: Releasing The Service Position
MAINTENANCE FR 2113 MA, FR 2115 MA WARNING! Exercise care so that your hands are not crushed. 7. Lift off the drive belt (1). Now pull out the split pin (2). 6017-225 8. Pull the frame forwards and refit the pin. 6017-226 9. -
Page 42: Inspecting The Blades
MAINTENANCE Inspecting the blades It is important that the blades are undamaged and well-ground to give the best mowing result. Check that the blades’ mounting bolts are tightened. IMPORTANT INFORMATION Replacement or sharpening of the blades should be carried out by an authorised service workshop. -
Page 43: Lubrication
LUBRICATION FR 2111, FR 2113 Checking the engine’s oil level Check the oil level in the engine when the Rider stands horizontal with the engine switched off. Fold up the engine cover. Loosen the dipstick and pull it out. Wipe off the dipstick and fit it again. -
Page 44: Checking The Engine's Oil Level Fr 2115
LUBRICATION FR 2115 Check the engine’s oil level Check the oil level in the engine when the Rider stands horizontal with the engine switched off. Fold open the engine cover. Release the dip stick and pull out. Wipe off the oil and insert again. -
Page 45: Checking The Oil Level In The Transmission
LUBRICATION Checking the oil level in the transmission on FR 2113, FR 2115 1. Remove the transmission cover. Loosen both screws (one on each side) and lift off the transmission cover. 8009-273 2. Check that there is oil in the transmission’s oil tank. -
Page 46: Lubricating The Front Wheel Bearings
LUBRICATION Lubricating the front wheel bearings The front cover and wing covers must be removed on machines with rear ejection, so that the tubular loop can be lifted to remove the wheel. 1. Remove the plastic cover that covers the centre of the wheel. -
Page 47: Trouble Shooting Chart
TROUBLE SHOOTING CHART Problem Cause The engine will not start • No fuel in the fuel tank • Faulty spark plug • Fault spark plug connection • Dirt in the carburettor or fuel line Starter does not turn the engine •... -
Page 48: Storage
STORAGE To ready the Rider for storage, follow these steps: Winter storage 1. Clean the Rider carefully, especially under the At the end of the mowing season the Rider should mowing deck. Touch up damage to the paint to be readied for storage, likewise if it will not be in prevent rust. -
Page 49: Technical Data
TECHNICAL DATA Dimensions FR 2111 FR 2113 A Length with mowing deck 2040 mm/6.6 ft 2040 mm/6.6 ft Width 880 mm/2.89 ft 880 mm/2.89 ft Height 1070 mm/3.52 ft 1070 mm/3.52 ft Weight with mowing deck 216 kg/475 lbs 219 kg/481 lbs Distance between axles 860 mm/2.81 ft 850 mm/2.81 ft... - Page 50 TECHNICAL DATA Dimensions FR 2113 MA FR 2115 MA Length without mowing deck 2010 mm/6.58 ft 2010 mm/6.58 ft Length with mowing deck 2220 mm/7.29 ft 2220 mm/7.29 ft Width without mowing deck 880 mm/2.89 ft 880 mm/2.89 ft Width with mowing deck 1000 mm/3.29 ft Height 1070 mm/3.52 ft...
- Page 51 TECHNICAL DATA Mowing deck Type Triple blade cover Double blade cover Triple blade cover with rear ejection Mulching 900 mm Mulching 1030 mm Mowing width 850 mm/33.5" 900 mm/35.5" 1030 mm/40.5" Cutting heights 9 positions 40-90 mm/1 9/16" - 3 9/16" 45-95 mm/1 3/4"...
-
Page 52: Eu Declaration Of Conformity
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel: +46-36-146500, declares under sole responsibility that the Rider Jonsered FR 2111, FR 2113 A, FR 2113 MA, FR 2115 MA, from 2002’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVES:... -
Page 53: Service Schedule
SERVICE SCHEDULE Date, mileage reading, stamp, signature Action Delivery service 1. Fill the battery with battery acid and charge for four hours. 2. Fit the steering wheel, towing eye and where applicable other components. 3. Adjust the mowing deck: Adjust the lifting springs (the weight of the mowing deck should be 12-15 kg/26.5-33 lbs). -
Page 54: Service Journal
SERVICE JOURNAL Date, mileage reading, stamp, signature Action ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○... - Page 55 English –...
- Page 56 108 88 71-26 ´*xw,¶6•¨ 2002W38...