Jonsered FR 2312 MA Operator's Manual
Lawn mower
Hide thumbs
Also See for FR 2312 MA:
- Operator's manual (120 pages) ,
- Workshop manual (47 pages) ,
- Operator's manual (28 pages)
Related Manuals for Jonsered FR 2312 MA
Summary of Contents for Jonsered FR 2312 MA
- Page 1 Oper ator ′ s manual Please read the oper ator’s manual carefully and make sure you understand the instructions before using the machine. FR2312 MA FR2312 M...
-
Page 2: Table Of Contents
CONTENTS Contents Checking the blades ............. Replacing the blades ............ CONTENTS Removing the Mulching plug ........Contents ..............Lubrication INTRODUCTION Checking the engine’s oil level........Dear Customer, ............Replacing the engine oil ..........Driving and transport on public roads ......Lubricating the front wheel bearings ...... -
Page 3: Introduction
Dear Customer, Thank you for choosing a Jonsered Frontrider. Jonsered Frontriders are built to a unique design with a front-mounted cutting unit and a patented rear-wheel steering system. FrontRiders are designed for maximum efficiency even in small or confined areas. The closely grouped controls and pedal-operated hydrostatic transmission also contribute to the performance of this machine. -
Page 4: Service Journal
Service journal Pre-delivery service 1 Charge the battery for 4 hours at max. 3 amp. 2 Fit steering wheel, seat and any optional equipment. 3 Check and adjust tyre pressure. (60 kPa, 0.6 bar, 9 psi). 4 Check that the right amount of oil is in the engine. 5 Make sure the battery is connected. -
Page 5: Key To Symbols
KEY TO SYMBOLS Clutch out Symbols These symbols are on the machine and in the instructions. Parking brake WARNING! Careless or incorrect use can result in serious or fatal injury to the operator or others. Brake Please read the operator’s manual carefully and make sure you understand the instructions before using the machine. -
Page 6: Safety Instructions
SAFETY INSTRUCTIONS • Stop the engine and prevent the engine from being Safety instructions started until you have cleaned the outlet channel. These instructions are for your safety. Read them carefully. • Look out for the ejector and do not direct it towards anyone. -
Page 7: Driving On Slopes
SAFETY INSTRUCTIONS • Never use the machine in bad weather, for instance in fog, Driving on slopes in rain, damp or in wet locations,strong winds, intense cold, risk of lightning, etc. Driving on slopes is one of the operations where the risk of the driver losing control of the machine or of it overturning is •... -
Page 8: Children
SAFETY INSTRUCTIONS • Do not try to stabilize the machine by putting your foot on Maintenance the ground. • Stop the engine. Prevent starting by removing the ignition • When cleaning the chassis, the machine may never be cable from the spark plug or remove the ignition key driven near verges or ditches. -
Page 9: Transport
SAFETY INSTRUCTIONS • Be especially careful when handling battery acid. Acid on • Reduce the risk of fire by removing grass, leaves and the skin can cause serious corrosive injuries. In the event other debris that may have fastened on the machine. of spillage on the skin wash immediately with water. -
Page 10: What Is What
WHAT IS WHAT? Location of the controls FR2312 MA 1 Product and serial number plate 8 Speed limiter for driving forward 2 Lever to disengage the drive 9 Cutting height adjustment lever 3 Battery 10 Parking brake 4 Throttle control/choke control 11 Lock button for parking brake 5 Ignition lock 12 Seat adjustment. -
Page 11: What Is What
WHAT IS WHAT? Location of the controls FR2312 M 1 Product and serial number plate 8 Parking brake 2 Battery 9 Cutting height adjustment lever 3 Throttle control/choke control 10 Clutch pedal 4 Gear shift lever 11 Seat adjustment. 5 Ignition lock 12 Fuel cap 6 Lifting lever for the cutting unit 13 Cover lock... -
Page 12: Presentation
PRESENTATION Presentation Speed limiter FR2312 MA The speed of the machine is steplessly regulated with two Congratulations on your choice of an excellent quality product pedals. Pedal (1) is used to drive forwards, and pedal (2) to that will give you great pleasure for many years. drive backwards. -
Page 13: Cutting Height Adjustment Lever
PRESENTATION Cutting height adjustment lever Release lever FR2312 MA The cutting height can be adjusted to 5 (1-5) different The release control must be pulled out in order for the positions with the cutting height lever. machine to be moved when the engine is shutoff. Pull the controls to the end positions, do not use an intermediate position. -
Page 14: Driving
Driving Before starting Start the engine • Read the safety instructions and information concerning Check the safety system the placement of controls and functions before starting. • Perform daily maintenance before starting as set out in The machine is equipped with a safety system that prevents the Maintenance schedule. -
Page 15: Starting The Engine With A Weak Battery
Driving FR2312 M has the brake pedal and lock button on the right 8 When the engine starts release the ignition key hand side. The engine can not be started if the parking brake immediately back to neutral position. is not pressed down. 9 Move the choke lever gradually back once the engine has 4 For FR2312 M started. -
Page 16: Driving The Rider
Driving Connecting the jump leads Driving the Rider 1 FR2312 MA Release the parking brake by first pressing down the parking brake pedal and then releasing it. Carefully press down one of the pedals until the required speed is obtained. Pedal (1) is used to drive forwards, and pedal (2) to drive backwards. -
Page 17: Starting On A Slope, Manual Gearbox
Driving 2 Select the required cutting height (1-5) using the cutting Stop the engine height lever. Always park the machine on a level surface with the engine OFF. 1 FR2312 MA Lift up the cutting unit by pulling the lever backwards to its locked position. -
Page 18: Maintenance
Maintenance Maintenance schedule The following is a list of the maintenance which should be conducted on the machine. For those points not described in this manual, visit an authorised service workshop. Daily maintenance At least once Maintenance interval Maintenance before starting a year in hours Cleaning... -
Page 19: Cleaning
Maintenance Cleaning Belt Guard Release the clip and lift off the belt guard. Clean the machine directly after use. It is much easier to wash off grass cuttings before they dry. Checking and adjusting the steering wires IMPORTANT INFORMATION Always park the machine on The steering is controlled by means of wires. -
Page 20: Checking The Parking Brake
Maintenance Checking the parking brake Adjusting the throttle wire Check that the brake is correctly adjusted by placing the The throttle cable may need to be adjusted, if the engine does machine on a slight downhill slope with the clutch disengaged not respond as it should when accelerating, if it produces and activating the brake. -
Page 21: Replacement Of Fuel Filter
Maintenance Checking the tyre pressure IMPORTANT INFORMATION Do not use compressed air to clean the paper filter. The tyre pressure should be 60 kPa / 0.6 bar / 8,7 PSI on all wheels. In order to improve drive power, the pressure in the Do not oil the paper filter. -
Page 22: Fuses
Maintenance Fuses Checking the engine’s cooling air intake The main fuse is placed in a detachable holder behind the battery under the protective cover. Clean the air intake grille in the engine cover behind the driver’s seat. Type: Flat pin, 15 A. Open the engine cover. -
Page 23: Service Position For The Cutting Unit
Maintenance 7 Disengage the spring for the drive belt tensioning wheel. Service position for the cutting unit The cutting deck can be removed in order to facilitate cleaning and servicing. IMPORTANT INFORMATION Avoid cutting when the cutting head is placed in service position, to prevent damaging to the drive belt. -
Page 24: Fitting The Cutting Head
Maintenance 6 Tension the belt with the belt adjuster. Fitting the cutting head 1 Push the cutting deck in and make sure the guide bolts fit into the grooves on the deck frame, one on each side. 7 Install the belt cover. 8 Set the cutting deck height control in any of the positions 2 Fit the cutting deck's pipe together with the deck frame's 1-5. -
Page 25: Checking The Blades
Maintenance • The blade must be mounted with the angled ends pointing Checking the blades up towards the cover. To achieve the best mowing results it is important that the blades are undamaged and well-sharpened. • Check that the blades’ attachment screws are tight. •... -
Page 26: Lubrication
Lubrication 5 Fill the oil slowly. The oil is topped up through the hole the Checking the engine’s oil level. dipstick sits in. See Checking the engine’s oil level for filling instructions. Check the oil level in the engine when the Rider stands horizontal with the engine switched off. -
Page 27: Troubleshooting Schedule
Troubleshooting schedule Problem Cause There is no fuel in the fuel tank Faulty spark plug. Defective ignition cable. Engine does not start Dirt in the carburettor or fuel line Starter motor does not turn over the engine Defect safety switch Battery flat Bad contact between the cable and battery Lift lever for cutting unit in wrong position... -
Page 28: Storage
Storage Winter storage Guard At the end of the season, or if the machine is going to stand There is a cover to protect your machine during storage or idle for more than 30 days, it should immediately be made transport. -
Page 29: Technical Data
TECHNICAL DATA FR2312 M FR2312 MA Dimensions Length without cutting unit, mm/ft 1781/5.84 1781/5.84 Length with cutting unit, mm/ft 2100/6.89 2100/6.89 Width without cutting unit, mm/ft 797/2.61 793/2.60 Width with cutting unit, mm/ft 883/2.90 883/2.90 Height, mm/ft 1084/3.56 1084/3.56 Machine without cutting unit, with empty tanks, kg/lb 154/340 154/340 Wheel base, mm/ft... -
Page 30: Ec Declaration Of Conformity
EC Declaration of Conformity (Applies to Europe only) Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +46-36-146500, hereby declares that Jonsered FR2312 MA, FR2312 M from 2014’s serial numbers and onwards (the year is clearly stated in plain text on the rating plate with subsequent serial number), complies with the requirements of the COUNCIL’S DIRECTIVE:... - Page 32 Original instructions 1156989-26 ´®z+X§|¶6z¨ ´®z+X§|¶6z¨ 2014-06-11...