Installation
•
Verify correct model, options and voltage from unit
nameplate.
•
Verify that the installation location of the unit will
provide the required clearance for proper operation.
•
Assemble and install the roof curb (if applicable). Refer
to the latest edition of the curb installers guide that
ships with each curb kit.
•
Fabricate and install ductwork; secure ductwork to
curb.
•
Install pitch pocket for power supply through building
roof. (If applicable)
•
Rigging the unit.
•
Set the unit onto the curb; check for levelness.
•
Ensure unit-to-curb seal is tight and without buckles or
cracks.
•
Install and connect a condensate drain line to the
evaporator drain connection.
Note: Condensate Overflow Switch (if equipped) will not
work if unit is not leveled properly.
Factory Installed Economizer
•
Ensure the economizer has been pulled out into the
operating position. Refer to the economizer
installation guide for proper position and setup.
•
Install all access panels.
Table 3.
TC01 tripping values
TCO1 Tripping
Unit Model (Std.
Values - Downflow/
Eff.)
YSC036E**(L,X)-DD
YSC036E**(L,X)-BD
YSC036E**(M,Y)-DD
YSC036E**(M,Y)-BD
YSC036E**(H,Z)-DD
YSC036E**(H,Z)-BD
YSC048E**(L,X)-DD
YSC048E**(L,X)-BD
YSC048E**(H,Z)-DD
YSC048E**(M,Y)-BD
YSC048E**(M,Y)-DD
YSC048E**(H,Z)-BD
YSC060E**(L, X)
YSC060E**(M,Y)
YSC060E**(H,Z)-DD
YSC060E**(H,Z)-BD
YSC072F**(M,Y)
continued on next page
28
Unit Model - (High
Horizontal
Eff. - 15 SEER)
180F
YHC036E**(L,X)-DD
170F
YHC036E**(L,X)-BD
170F / 190F
YHC036E**(M,Y)-DD
180F / 190F
YHC036E**(M,Y)-BD
170F / 190F
YHC036E**(H,Z)-DD
155F / 190F
YHC036E**(H,Z)-BD
180F
YHC048E/F**(L,X)-DD
170F
YHC048E/F**(L,X)-BD
155F / 210F
YHC048E/F**(M,Y)-DD
170F / 190F
YHC048E/F**(M,Y)-BD
180F
YHC048E/F**(H,Z)-DD
155F / 200F
YHC048E/F**(H,Z)-BD
170
YHC060E/F**(L,X)-DD
170F
YHC060E/F**(L,X)-BD
170F / 200F
YHC060E/F**(M,Y)-DD
170F
YHC060E/F**(M,Y)-BD
155F
YHC060E/F**(H,Z)-DD
Temperature Limit Switch Usage for Gas
Heat Units
Units are factory shipped in the down flow discharge
configuration but can be field converted to a horizontal
discharge configuration. Some, but not all units require a
differentTCO1 limit switch, which is attached to the
combustion blower motor if horizontal discharge
configuration is used.
Note: The following units require a limit switch change
out for horizontal discharge.The additional limit
switch is shipped attached to the combustion
blower housing:YSC036E**(M,Y),
YSC036E**(H,Z),YSC048E**(H,Z),
YSC048E**(M,Y) belt drive ID motor,
YSC060E**(H,Z) direct drive ID motor,
YHC047E**(L,X),YHC048E/F**(L,X) direct drive ID
motor,YHC060E/F**(L,X) belt drive ID,
YHC036E**(M,Y),YHC037E**(M,Y),YHC048E/
F**(M,Y),YHC060E/F**(M,Y) direct drive ID motor,
YHC036E**(H,Z),YHC048E/F**(H,Z) belt drive ID
motor,YHC060E/F**(H,Z),YSC072F**(H,Z),
YSC090F**(L,X),YSC092F**(H,Z),
YSC102F**(H,Z),YSC120F**(L,X),
YSC120F**(H,Z),YHC092F**(M,Y),
YHC102F**(M,Y),YHC120E**(H,Z).
If any of the aforementioned units are installed in the down
flow discharge configuration, remove the additionalTCO1
limit switch from the combustion blower motor and
discard.
BD= Belt drive ID motor
DD= Direct drive ID motor
TCO1 Tripping
Values -Downflow/
Unit Model
Horizontal
(High Eff. - 17 Plus)
180F
YHC037**(L,X)
170F
YHC037**(M,Y)
170F / 190F
YHC037**(H,Z)
180F / 190F
YHC047**(L,X)
170F / 190F
YHC047**(M,Y)
155F / 190F
YHC047**(H,Z)
145F / 155F
YHC067**(L,X)
155F
YHC067**(M,Y)
150F / 170F
YHC067**(H,Z)
170F / 180F
220F
220F / 260F
140F
155F / 145F
145F / 170F
170F
190F / 220F
TCO1 Tripping
Values -Downflow/
Horizontal
190F
170F / 220F
220F
145F / 155F
170F
220F
140F
170F
170F
RT-SVX21P-EN