Error Messages - Denon AVR-1609 Owner's Manual

ENGLISH
fa
• To proceed to "Step 5" without checking the analysis result. use b.. "i7 to select "Store<"
while "Parameter Check<" is displayed.
• Values that are different from the actual distance may be set for speakers with built-in filters
(subwoofers. etc). This is because filters add electrical delay to the signal that should be
compensated.
•
'v
"".'f~
'XT
iWu"";""if."v'
.....
:ii/!:.
I
I ,.
The included setup microphone is not • Connect the included setup
1' 1
i
c
Or"·
SF-:
t'~one
I
connected. microphone to
<SETUP MIC>.
:. Not all speakers could be detected. • Check the speaker connections.
I
I
• Too much noise in the room for • Either turn off any deVice generating
Ai'le.
i
ent t·~o
i
se
accurate measurements
to
be made. noise or move it away.
• Try again when the surroundings are
quieter.
• Speaker or subwoofer sound is too • Check the speaker installation and the
low for accurate measurements to be direction in which the speakers are
made. facing.
• Adjust the subvvoofer's volume.
I
I
I.
Displayed speaker could
not be • Check
the connections of the
C.:aut i on: SF'
t'~one
detected. displayed speaker.
t
· The front L and front R speakers
The messages alternate
were not properly detected.
· Only one channel of the surround
I I
speakers was detected.
FF.:
· Sound was output from the R
channel when only one surround
back speaker was connected.
· The surround back speaker was
detected. but the surrounds were
not detected.
I I
:. Displayed speaker connected with • Check the polarities of the displayed
C.:iut
j
on: F'h.::ise
the polarities reversed. speaker.
t
The messages alternate
• For
some speakers, this error
message may be displayed even if the
speaker is properly connected. If the
I
I
connection is correct. use the /:;. or "i7
SBL
bunons to display "Skip<" and then
press
<l.
g;}[:~
Select" Retry" to make the measurements again.
-N.na
Be sure to turn the power off before crrecking speaker connections.
)
)
( Step 4 : Check
f.JTo proceed to "Step 5; Store"
During display of crossover frequency result or analysis results item. press
ENTER.
• "Store<" is displayerj
When analysis is complete. "Parameter Check<" is displayed.
Press
<l
and check the analysis results for the follOWing four items.
(1) Make your selectiOn using b.. "i7 and press
<l.
• Presence and size of speaker
"SpConfi(j. Check<"
• Distance of speaker from listening position
"Distance Check<"
• Speaker channel level
"Ch Level Check<"
• Crossover Frequency
"Crossover Check<"
:l'
Use /:;. or
"i7
to change which speaker is displayed.
uTo switch to another analysis result item
Press
ENTER.
This returns you to analysis results items. so repeat operation
CD.
( Step 5 : Store
Ttle auto setup measurement results are stored in Hle AVR-1609.
(T'
Press
<l
while "Store<" is displayed
• "Storing" blinks on the display panel while the results are being stored.
• When storing is complete. "Completed" is displayed followed by "Disconnect Mic".
@
Disconnect the setup microphone from the AVR-1609.
u To cancel storing
Use /:;. or "i7
to
display "Cancel<" while "Store<" is displayed and press
<l.
• All the measured auto setup data Will be erased .
•
~[.ii.
Do not tum the power off while the settings are being stored.
20