Error Messages - Denon AVR-4311 Owner's Manual

Error messages

An error message is displayed if Audyssey ® Auto Setup could not be completed due to speaker placement, the measurement environment, etc.
If this happens, check the relevant items, be sure to take the necessary measures, then perform Audyssey Auto Setup over again.
NOTE
Be sure to turn off the power before checking speaker connections.
Examples
AUDYSSEY AUTO SETUP
Caution! 1 2 3 4 5 6
The subwoofer's level is too high or low. Please select "SW
Level Matching" and adjust the level of your subwoofer unit.
If you do not want to use the
subwoofer, select "Skip".
SW Level Matching
Skip
Enter Cancel
RETURN
Proceed to subwoofer volume adjustment item
AUDYSSEY AUTO SETUP
Caution!
No microphone or speaker
Retry
Cancel
RETURN
Check cause of problem!
AUDYSSEY AUTO SETUP
Caution!
Ambient noise is too high
or Level is too low
Retry
Cancel
RETURN
Check cause of problem!
AUDYSSEY AUTO SETUP
Caution! 1 2 3 4 5 6
Front R None
Retry
Cancel
RETURN
Check cause of problem!
AUDYSSEY AUTO SETUP
1 2 3 4 5 6
Caution!
Front L Phase
Retry
Skip
Cancel
RETURN
Check cause of problem!
Remote control operation
buttons
Error details
• Correct measurement is not possible due to
inappropriate subwoofer volume.
• The connected setup microphone is broken,
or a device other than the supplied setup
microphone is connected.
• Not all speakers could be detected.
• The front L speaker was not properly
detected.
• There is too much noise in the room for
accurate measurements to be made.
• Speaker or subwoofer sound is too low for
accurate measurements to be made.
• The displayed speaker could not be detected. • Check the connections of the displayed
• The displayed is connected with the
polarities reversed.
Move the cursor
(Up/Down/Left/Right)
Measures
• When using a subwoofer with built-in
amplifi er (active type), use "SW Level
Matching" to adjust the subwoofer volume
(vpage 11 "Subwoofer level error message
and how to adjust").
• When using a subwoofer without a built-in
amplifi er, select "Skip", and then press
ENTER
.
• Connect the included setup microphone to
the SETUP MIC jack of this unit.
• Check the speaker connections.
• Either turn off any device generating noise
or move it away.
• Perform again when the surroundings are
quieter.
• Check the speaker installation and the
direction in which the speakers are facing.
• Adjust the subwoofer's volume.
speaker.
• Check the polarities of the displayed
speaker.
• For some speakers, this error message may
be displayed even if the speaker is properly
connected. If you are sure the connection is
correct, press ui to select "Skip", then
ENTER
press .
Confi rm the setting
Subwoofer level error message and how to adjust
The optimal level of each subwoofer channel for Audyssey
Auto Setup measurement is 75 dB. During subwoofer level
(Audyssey ®
measurement ("Set up speakers
STEP2 Detection & Measurement " (vpage 9), 6 – q), an error
message is displayed when one level of subwoofers is outside the 72
– 78 dB range. When using a subwoofer with built-in amplifi er (active
type), adjust the subwoofer volume so that the subwoofer level is
within the 72 to 78 dB range.
1
Select "SW Level Matching" and then press
AUDYSSEY AUTO SETUP
Caution!
The subwoofer's level is too high or low. Please select "SW
Level Matching" and adjust the level of your subwoofer unit.
If you do not want to use the
subwoofer, select "Skip".
SW Level Matching
Skip
Enter
RETURN
Proceed to subwoofer volume adjustment item
Return to previous menu
ENGLISH
Auto Setup),
ENTER
.
1 2 3 4 5 6
Cancel
11