Sign in today to find solutions:

Don't have an account? Sign up

Integra DTR-5.8 Instruction Manual

Integra a/v receiver instruction manual.

 
AV Receiver
DTR-5.8
Instruction Manual
Next page ->

Summary of Contents

  • Page 1

    AV Receiver DTR-5.8 Instruction Manual...

  • Page 2

    WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS APPARATUS TO RAIN OR MOISTURE. CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING QUALIFIED PERSONNEL.

  • Page 3

    Precautions 1. Recording Copyright—Unless it’s for personal use only, recording copyrighted material is illegal with- out the permission of the copyright holder. 2. AC Fuse—The AC fuse inside the unit is not user- serviceable. If you cannot turn on the unit, contact the dealer from whom you purchased this unit.

  • Page 4: Supplied Accessories

    Thank you for purchasing an Integra AV Receiver. Please read this manual thoroughly before making con- nections and plugging in the unit. Following the instructions in this manual will enable you to obtain optimum performance and listening enjoyment from your new AV Receiver.

  • Page 5: Table Of Contents

    Main Room...88 Using the Remote Controller in Zone 2 and Multiroom Control Kits...89 Controlling Other Components... 90 Entering Remote Control Codes...90 Remote Control Codes for Integra Components Connected via Resetting Remote Mode Buttons...91 Resetting the Remote Controller ...91 Others Specifications ...

  • Page 6: Features

    Features Amplification • 90 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz with a maximum total harmonic distortion of 0.08 % (FTC rating) • WRAT-Wide Range Amplifier Technology • Optimum Gain Volume Circuitry Processing •...

  • Page 7: Front Panel

    Front & Rear Panels Front Panel North American model 2 3 4 bq br Australian model 2 cn 3 The page numbers in parentheses show where you can find the main explanation for each item. Standby/On button (40) This button is used to set the AV receiver to Standby or On.

  • Page 8

    Front & Rear Panels—Continued Tuning Mode button (57) This button is used to select the Auto or Manual tuning mode. Display button (55) This button is used to display various information about the currently selected input source. Setup button This button is used to access the onscreen setup menus that appear on the connected TV.

  • Page 9: Display

    Front & Rear Panels—Continued Display The page numbers in parentheses show where you can find the main explanation for each item. SLEEP indicator (56) This indicator lights up when the Sleep function has been set. MUTING indicator (56) This indicator flashes or lights up while the AV receiver is muted.

  • Page 10: Rear Panel

    Front & Rear Panels—Continued Rear Panel North American model (North American model only) The page numbers in parentheses show where you can find the main explanation for each item. DIGITAL OPTICAL IN 1, 2 and OUT These optical digital audio inputs are for connecting components with optical digital audio outputs, such as CD players and DVD players.

  • Page 11

    Front & Rear Panels—Continued AC INLET This connector is for connecting the supplied power cord. REMOTE CONTROL This (Remote Interactive) jack can be con- nected to an jack on another -capable Inte- gra component. The AV receiver’s remote controller can then be used to control that component. To use , you must make an analog audio connection (RCA) between the AV receiver and the other AV component, even if they are connected digitally.

  • Page 12: Remote Controller, Installing The Batteries, Aiming The Remote Controller

    Remote Controller Installing the Batteries To open the battery compartment, press the small hollow and slide off the cover. Insert the two supplied batteries (AA/R6) in accordance with the polarity diagram inside the battery compartment. Put the cover onto the remote controller and slide it shut.

  • Page 13: Using The Remote Controller, Receiver/tape Mode

    Receiver/Tape Mode Receiver/Tape mode is used to control the AV receiver. It can also be used to control an Integra cassette recorder connected via Buttons , and are used when the Tuner or...

  • Page 14

    Remote Controller—Continued For detailed information, see the pages in parentheses. Zone 2 button (86) Used to select the input source for Zone 2. Standby/On button (40) Sets the AV receiver to Standby or On. Input Selector buttons (54) Used to select the input sources. Multi CH button (55) Selects the multichannel DVD input.

  • Page 15: Dvd Mode

    Remote Controller—Continued DVD Mode By default, the remote controller is set to control an Inte- gra DVD player. To select your DVD player as the input source, press: Standby/On button Sets the DVD player to Standby or On. Number buttons Used to enter title, chapter, and track numbers and times for locating specific points.

  • Page 16: Cd/md/cdr/dock Mode

    Remote Controller—Continued CD/MD/CDR/Dock Mode By default, the remote controller is set to control an Inte- gra CD player. To select the input source, press: * If you’re using an MD, CDR, or RI Dock, you must change the input display (see page 51). Standby/On button Sets the component to Standby or On.

  • Page 17: About Home Theater, Enjoying Home Theater

    About Home Theater Enjoying Home Theater Thanks to the AV receiver’s superb capabilities, you can enjoy surround sound with a real sense of movement in your own home—just like being in a movie theater or concert hall. With DVDs you can enjoy DTS and Dolby Digital. With analog and digital TV you can enjoy Dolby Pro Logic IIx or Onkyo’s own DSP surround listening modes.

  • Page 18: About Av Connections

    Connecting the AV receiver About AV Connections • Before making any AV connections, read the manuals supplied with your other AV components. • Don’t connect the power cord until you’ve completed and double-checked all AV connections. Optical Digital Jacks The AV receiver’s optical digital jacks have shutter-type covers that open when an optical plug is inserted and close when it’s removed.

  • Page 19

    Connecting the AV receiver—Continued Connecting Your Speakers Speaker Configuration For the best surround sound experience, you should con- nect seven speakers and a powered subwoofer. The following table indicates the channels you should use depending on the number of speakers that you have. Number of speakers: ✓...

  • Page 20

    Connecting the AV receiver—Continued Speaker Connection Precautions Read the following before connecting your speakers: • North American models: Only connect speakers with an impedance of 6 ohms or higher. If you use speakers with a lower impedance, and use the ampli- fier at high volume levels for a long period of time, the built-in protection circuit may be activated.

  • Page 21: Bi-amping The Front Speakers

    Connecting the AV receiver—Continued Bi-amping the Front Speakers The FRONT L/R and SURR BACK L/R terminal posts can be used with front speakers and surround back speakers respectively, or bi-amped to provide separate tweeter and woofer feeds for a pair of front speakers that support bi-amping, providing improved bass and treble performance.

  • Page 22: Connecting Antenna

    Connecting the AV receiver—Continued Connecting Antenna This section explains how to connect the supplied indoor FM antenna and AM loop antenna, and how to connect commercially available outdoor FM and AM antennas. The AV receiver won’t pick up any radio signals without any antenna connected, so you must connect the antenna to use the tuner.

  • Page 23

    Connecting the AV receiver—Continued Connecting an Outdoor FM Antenna If you cannot achieve good reception with the supplied indoor FM antenna, try a commercially available out- door FM antenna instead. Notes: • Outdoor FM antennas work best outside, but usable results can sometimes be obtained when installed in an attic or loft.

  • Page 24: Which Connections Should I Use

    Connecting the AV receiver—Continued Connecting Both Audio & Video By connecting both the audio and video outputs of your DVD player and other AV components to the AV receiver, you can select both the audio and video simultaneously simply by selecting the appropriate input source on the AV receiver. : Signal Flow Video Audio...

  • Page 25

    Connecting the AV receiver—Continued ■ HDMI Monitor Setting Set to No With the HDMI Monitor setting set to No (see page 47), video input signals flow through the AV receiver as shown, with composite video and S-Video sources being upconverted for the com- ponent video output.

  • Page 26: Connecting Your Tv Or Projector

    Connecting the AV receiver—Continued Connecting Your TV or Projector Step 1: Video Connection Choose a video connection that matches your TV ( , Step 2: Audio Connection Choose an audio connection that matches your TV ( , • With connection , you can listen to and record audio from your TV and listen in Zone 2.

  • Page 27: Connecting A Dvd Player

    Connecting the AV receiver—Continued Connecting a DVD Player Step 1: Video Connection Choose a video connection that matches your DVD player ( , You must connect the AV receiver to your TV via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your DVD player ( , •...

  • Page 28

    Connecting the AV receiver—Continued Hooking Up the Multichannel DVD Input If your DVD player supports multichannel audio formats such as DVD-Audio or SACD, and it has a multichannel analog audio output, you can connect it to the AV receiver’s multichannel DVD input. Use a multichannel analog audio cable, or several normal audio cables, to connect the AV receiver’s DVD IN FRONT L/R, CENTER, SURR L/R, SURR BACK L/R, and SUBWOOFER jacks to the 7.1-channel analog audio output on your DVD player.

  • Page 29: Connecting A Vcr Or Dvd Recorder For Playback

    Connecting the AV receiver—Continued Connecting a VCR or DVD Recorder for Playback With this hookup, you can use your VCR’s tuner to listen to your favorite TV programs via the AV Hint! receiver, useful if your TV has no audio outputs. Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( , You must connect the AV receiver to your TV via the same type of connection.

  • Page 30: Connecting A Vcr Or Dvd Recorder For Recording

    Connecting the AV receiver—Continued Connecting a VCR or DVD Recorder for Recording Step 1: Video Connection Choose a video connection that matches your VCR or DVD recorder ( video source to be recorded must be connected to the AV receiver via the same type of connection. Step 2: Audio Connection Choose an audio connection that matches your VCR or DVD recorder ( Connection...

  • Page 31: Connecting A Satellite, Cable, Set-top Box, Or Other Video Source

    Connecting the AV receiver—Continued Connecting a Satellite, Cable, Set-top box, or Other Video Source With this hookup, you can use your satellite or cable receiver to listen to your favorite TV programs Hint! via the AV receiver, useful if your TV has no audio outputs. Step 1: Video Connection Choose a video connection that matches the video source ( , You must connect the AV receiver to your TV via the same type of connection.

  • Page 32: Connecting A Game Console

    Connecting the AV receiver—Continued Connecting a Game Console Step 1: Video Connection Choose a video connection that matches the game console ( , If you use connection , you must connect the AV receiver to your TV with the same type of connection. Step 2: Audio Connection Choose an audio connection that matches the DVD player ( •...

  • Page 33: Connecting A Camcorder Or Other Device

    Connecting the AV receiver—Continued Connecting a Camcorder or Other Device Step 1: Video Connection Choose a video connection that matches the camcorder ( Step 2: Audio Connection Choose an audio connection that matches the camcorder ( Connection AV receiver AUX Input S Video AUX Input Video AUX Input Audio L/R AUX Input Digital...

  • Page 34: Connecting Components With Hdmi

    Connecting the AV receiver—Continued Connecting Components with HDMI About HDMI Designed to meet the demands of digital TV, HDMI (High Definition Multimedia Interface) is a new digital interface standard for connecting TVs, projectors, DVD players, set-top boxes, and other video components. Until now, several separate video and audio cables have been required to connect AV components.

  • Page 35

    Connecting the AV receiver—Continued Making HDMI Connections Step 1: Use HDMI cables to connect the AV receiver’s HDMI jacks to your HDMI-compatible DVD player, TV, projector, and so on. Step 2: Assign each HDMI IN to an input selector in the HDMI Input Setup (see page 48). ■...

  • Page 36: Connecting A Cd Player Or Turntable

    Connecting the AV receiver—Continued Connecting a CD Player or Turntable ■ CD Player or Turntable (MM) with Built-in Phono Preamp Step 1: Choose a connection that matches your CD player ( , phono preamp. COAXIAL IN 2 (CBL/SAT) Connect one or OPTICAL the other IN 2...

  • Page 37: Connecting An Ri Dock

    Connecting the AV receiver—Continued Connecting an RI Dock ■ RI Dock with video Connect your RI Dock’s analog audio output jacks and S-Video output jack to the AV receiver’s GAME/TV IN L/R jacks and GAME/TV IN S jack. (The example shown below is for connection with the DS-A1.) S VIDEO Notes:...

  • Page 38: Connecting A Power Amplifier

    Connecting the AV receiver—Continued Connecting a Cassette, CDR, MiniDisc, or DAT Recorder Step 1: Choose a connection that matches the recorder ( , COAXIAL IN 2 (CBL/SAT) OPTICAL IN 1 (GAME/TV) OPTICAL DIGITAL OUT Connect one or the other COAXIAL •...

  • Page 39: Connecting The Rs232 Port, Connecting The Power Cord

    • Some components may not support all Refer to the manuals supplied with your other Integra components. • If you connect an Integra MD recorder, CD recorder, or an Onkyo RI DOCK, you must change the input display (see page 51).

  • Page 40: Turning On The Av Receiver, Connecting The Power Cord, Turning On And Standby

    If you have, see “HDMI Input Setup” on page 48, “Component Video Setup” on page 49, or “Digital Input Setup” on page 50 respectively. ■ Have you connected an Integra MD recorder, CD recorder, or RI Dock? If you have, see “Changing the Input Display” on page 51.

  • Page 41: Automatic Speaker Setup (audyssey 2eq)

    First Time Setup This section explains the settings that you need to make before using the AV receiver for the very first time. Automatic Speaker Setup (Audyssey 2EQ) With the supplied speaker setup microphone, the Audyssey 2EQ function can measure the number of speakers connected, their sizes, crossover frequencies, and the distance from each speaker to the listening posi- tion and calculate the optimal speaker settings for your...

  • Page 42

    First Time Setup—Continued Put the speaker setup micro- phone at measurement point (page 41), and connect it to the Setup Mic jack. Please place microphone at center of listening area at ear height. Push Enter : Next Notes: • Make sure the microphone is hori- zontal.

  • Page 43

    First Time Setup—Continued The following screen appears. Auto Speaker Setup Please place microphone at left end of listening area at ear height. Push Enter : Next Move the speaker setup micro- phone to measurement point (page 41), then press [Enter]. Audyssey 2EQ performs more mea- surements.

  • Page 44

    First Time Setup—Continued Error Messages While the automatic speaker setup is in progress, one of the following error messages may appear: ❏ Ambient noise is too high Auto Speaker Setup Ambient noise is too high. Retry Cancel This message appears if the background noise is too loud and the measurements cannot be performed properly.

  • Page 45

    First Time Setup—Continued Reviewing the Results Use the Up and Down [ buttons to select the settings that you want to review, and then press [Enter]. Auto Speaker Setup Save Review SP Config Review SP Distance Review SP Level Cancel The options are: Review SP Config: Review the speaker configuration...

  • Page 46

    First Time Setup—Continued About the Onscreen Setup Menus The onscreen setup menus are displayed on the connected TV and provide a convenient way to change the AV receiver’s settings. Submenus p. 47 p. 50 1. Input/Output Assign 1. Monitor Out 2.

  • Page 47: Hdmi Monitor

    First Time Setup—Continued 2, 3 1, 5 HDMI Monitor If you connect your TV to the COMPONENT VIDEO OUT, set the HDMI Monitor setting to No so that the onscreen setup menus are displayed and composite video and S-Video sources are upconverted* and output by the COMPONENT VIDEO OUT.

  • Page 48: Video Input Setup

    First Time Setup—Continued Video Input Setup HDMI Input Setup If you connect a video component to HDMI IN 1 or 2, you must assign that input to an input selector. For exam- ple, if you connect your DVD player to HDMI IN 1, you must assign HDMI IN 1 to the DVD input selector.

  • Page 49

    First Time Setup—Continued Component Video Setup If you connect to a COMPONENT VIDEO IN, you must assign it to an input selector. For example, if you connect your DVD player to COMPONENT IN 3, you should assign it to the DVD input selector. If you want to output composite and S-Video sources from the COMPONENT VIDEO OUT, select “---,”...

  • Page 50: Digital Input Setup

    First Time Setup—Continued Digital Input Setup If you connect a component to a digital input jack, you must assign that jack to an input selector. For example, if you connect your CD player to the OPTICAL IN2 jack, you should assign that jack to the CD input selector. By default, the COAXIAL IN1 jack is assigned to the DVD input selector, although this can be changed.

  • Page 51: Changing The Input Display, Speaker Settings

    First Time Setup—Continued Changing the Input Display If you connect an -capable Integra MiniDisc recorder, CD recorder, or RI Dock to the TAPE IN/OUT or GAME/TV IN jacks, for to work properly, you must change this setting. This setting can only be changed on the AV receiver.

  • Page 52

    First Time Setup—Continued Use the Up and Down [ buttons to select “Speaker Impedance,” and then use the Left and Right [ select: 4 ohms: Select if the impedance of any speaker is 4 ohms or more but less than 6. 6 ohms: Select if the impedances of all speakers are between 6 and 16 ohms.

  • Page 53: Am Frequency Step Setup (australian Model)

    First Time Setup—Continued AM Frequency Step Setup (Australian model) You must specify the AM frequency step used in your area. Note that when this setting is changed, all radio presets are deleted. Press the [Receiver] button, fol- lowed by the [Setup] button. The main menu appears onscreen.

  • Page 54: Selecting The Input Source

    Basic Operations Selecting the Input Source This section explains how to select the input source (i.e., the AV component that you want to listen to or watch). Multi CH AV receiver Remote controller AV receiver Remote controller Use the AV receiver’s input selector buttons to select the input source.

  • Page 55: Using The Multichannel Dvd Input, Displaying Source Information

    Basic Operations—Continued Using the Multichannel DVD Input The multichannel DVD input is for connecting a compo- nent with a 7.1-channel analog audio output, such as a DVD-Audio or SACD-capable DVD player, or an MPEG decoder. See page 28 for hookup information. Press the [Receiver] button, fol- lowed by the [Multi CH] button.

  • Page 56: Setting The Display Brightness, Muting The Av Receiver, Using The Sleep Timer, Using Headphones

    Basic Operations—Continued Dimmer Setting the Display Brightness You can adjust the brightness of the display. Press the [Receiver] button, and then press the [Dimmer] button repeatedly to select: dim, dim- mer, or normal brightness. Alternatively, you can use the AV receiver’s [Dimmer] button.

  • Page 57: Listening To The Radio, Using The Tuner

    Listening to the Radio Using the Tuner With the built-in tuner you can enjoy AM and FM radio stations. You can store your favorite stations as presets for quick selection. Listening to the Radio Use the [Tuner] input selector button to select either AM or FM. In this example, FM has been selected.

  • Page 58: Presetting Am/fm Stations

    Listening to the Radio—Continued Presetting AM/FM Stations 2, 4 You can store a combination of up to 40 of your favorite AM/FM radio stations as presets. Tune into the AM/FM station that you want to store as a preset. Press the [Memory] button. The preset number flashes.

  • Page 59: Using The Listening Modes, Selecting Listening Modes

    Using the Listening Modes Selecting Listening Modes See “About the Listening Modes” on page 64 for detailed information about the listening modes. • The Dolby Digital and DTS listening modes can only be selected if your DVD player is connected to the AV receiver with a digital audio connection (coaxial or optical).

  • Page 60: Listening Modes Available For Each Source Format

    Using the Listening Modes—Continued Listening Modes Available for Each Source Format Analog and PCM Sources Source format 32-96 kHz Media Listening mode Direct Stereo Multichannel Dolby D Dolby Digital Plus DTS, DTS 96/24 DTS Discrete/Matrix DTS-HD High Resolution Audio DTS-HD Master Audio TrueHD Dolby PLII Movie/ Dolby PLIIx Movie...

  • Page 61

    Using the Listening Modes—Continued Dolby Digital, Dolby Digital Plus, and TrueHD Sources Multichannel Source format except Media DVD, DTV, etc. Listening mode ✔ ✔ Direct ✔ ✔ Stereo Multichannel ✔ ✔ Dolby D Dolby Digital Plus DTS, DTS 96/24 DTS Discrete/Matrix DTS-HD High Resolution Audio DTS-HD Master Audio...

  • Page 62

    Using the Listening Modes—Continued DTS and DTS 96/24 Sources Source format Media Listening mode Direct Stereo Multichannel Dolby D Dolby Digital Plus DTS, DTS 96/24 DTS Discrete/Matrix DTS-HD High Resolution Audio DTS-HD Master Audio TrueHD Dolby PLII Movie/ Dolby PLIIx Movie Dolby PLII Music/ Dolby PLIIx Music Dolby PLII Game/...

  • Page 63

    Using the Listening Modes—Continued DTS-HD High Resolution Audio and DTS-HD Master Audio Sources DTS-HD High Resolution Audio Source format Multichannel except *2 Media Listening mode ✔ Direct ✔ Stereo Multichannel Dolby D Dolby Digital Plus DTS, DTS 96/24 DTS Discrete/Matrix DTS-HD High Resolution ✔...

  • Page 64: About The Listening Modes

    Using the Listening Modes—Continued About the Listening Modes The AV receiver’s listening modes can transform your listening room into a movie theater or concert hall, with high fidelity and stunning surround sound. The illustration shows which speakers are active in each listening mode with 7.1 channel speaker sys- tem.

  • Page 65

    Using the Listening Modes—Continued DTS-ES Matrix This mode is for use with DTS-ES Matrix soundtracks, which use a matrix-encoded back-channel for 6.1/7.1- channel playback. Use it with DVDs that bear the DTS- ES logo, especially those with a DTS-ES Matrix soundtrack.

  • Page 66: Recording

    Recording This section explains how to record the selected input source to a component with recording capability, and how to record audio and video from different sources. Notes: • The surround sound and DSP listening modes cannot be recorded. • Copy-protected DVDs cannot be recorded. •...

  • Page 67: Using The Cinemafilter, Adjusting Individual Speaker Levels

    Advanced Operations Receiver CH SEL L Night Using the Late Night Function (Dolby Digital, Dolby Digital Plus, and Dolby TrueHD only) With the Late Night function, you can reduce the dynamic range of Dolby Digital, Dolby Digital Plus, and Dolby TrueHD material so that you can still hear quiet parts even when listening at low volume levels—ideal for watching movies late at night when you don’t want to disturb anyone.

  • Page 68

    Advanced Setup Speaker Setup Some of the settings in this section are set automatically by the Automatic Speaker Setup function (see page 41). Here you can check the settings made by the Automatic Speaker Setup function, or set them manually, which is useful if you change one of the connected speakers after using the Automatic Speaker Setup function.

  • Page 69

    Advanced Setup—Continued Use the Up and Down [ buttons to select “Center,” and then use the Left and Right [ ] buttons to select a crossover frequency. If no center speaker is connected, select None. Note: If the Front setting in step 5 is set to anything other than Full Band, Full Band cannot be selected here.

  • Page 70

    Advanced Setup—Continued Speaker Distance This setting is set automatically by the Automatic Speaker Setup function (see page 41). Here you can specify the distance from each speaker to the listening position so that the sound from each speaker arrives at the listener’s ears as the sound designer intended.

  • Page 71

    Advanced Setup—Continued Speaker Level Calibration This setting is set automatically by the Automatic Speaker Setup function (see page 41). Here you can adjust the level of each speaker with the built-in test tone so that the volume of each speaker is the same at the listening position.

  • Page 72

    Advanced Setup—Continued Equalizer Setting This setting is set automatically by the Automatic Speaker Setup function (see page 41). Here you can adjust the EQ of individual speakers. To set the volume of individual speakers see page 71. 2, 3 1, 8 Press the [Receiver] button fol- lowed by the [Setup] button.

  • Page 73: Multichannel Dvd Input Settings

    Advanced Setup—Continued Use the Up [ ] button to select “Channel,” and then use the Left and Right [ ] buttons to select another speaker. Repeat step 6 and 7 for each speaker. Press the [Setup] button. The setup menu closes. Notes: •...

  • Page 74: Audio Adjust Functions

    Advanced Setup—Continued Audio Adjust Functions Here you can set listening mode-related settings and functions. Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. Use the Up and Down [ buttons to select “3. Audio Adjust,”...

  • Page 75

    Advanced Setup—Continued PLIIx/Neo:6 Music Mode Settings These settings provide for playing any 2-channel digital source such as Dolby Digital, or 2-channel analog/PCM source in the Dolby PLIIx Music listening mode. ■ Panorama With this function, you can broaden the width of the front stereo image when using the Dolby Pro Logic II Music or Dolby Pro Logic IIx Music listening mode.

  • Page 76: Assigning Listening Modes To Input Sources

    Advanced Setup—Continued Assigning Listening Modes to Input Sources You can assign a default listening mode to each input source that will be selected automatically when you select each input source. For example, you can set the default listening mode to be used with Dolby Digital input signals.

  • Page 77: Source Setup

    Advanced Setup—Continued When you’ve finished, press the [Setup] button. The setup menu closes. Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Source Setup 2, 4 1, 6 IntelliVolume You can set the input level for each input source.

  • Page 78

    Advanced Setup—Continued Correcting Sound and Picture Sync When using progressive scanning on your DVD player, you may find that the picture and sound are out of sync. With this setting, you can correct this by delaying the audio signals. You can set it from 0 to 100 milliseconds (msec) in 2 millisecond steps.

  • Page 79: Volume Setup/osd Setup

    Advanced Setup—Continued Volume Setup/OSD Setup This section explains the items on the Miscellaneous menu. Volume Setup Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. Use the Up and Down [ buttons to select “6.

  • Page 80

    Advanced Setup—Continued OSD Setup Press the [Receiver] button fol- lowed by the [Setup] button. The main menu appears onscreen. Use the Up and Down [ buttons to select “6. Miscellaneous,” and then press [Enter]. The Miscellaneous menu appears. 6. Miscellaneous 1.

  • Page 81: Changing The Av Receiver's Id, Hdmi Setup

    AV receiver’s remote control ID. You may need to change this if the remote controller’s control codes overlap with those of another Integra component located in the same room. If you change the AV receiver’s remote control ID, be sure to set the same ID on both the AV receiver and remote controller (see page 83).

  • Page 82

    Advanced Setup—Continued HDMI Audio Out This preference determines whether audio received at the HDMI IN is output by the HDMI OUT. You may want to turn this preference on if your TV is connected to the HDMI OUT and you want to listen to the audio from a component that’s connected to an HDMI IN, through your TV’s speakers.

  • Page 83: Lock Setup, Digital Input Signal Formats, Changing The Remote Controller's Id

    If no digital input signal is present, the cor- responding analog input is used instead. Changing the Remote Controller’s ID If several Integra components are used in the same room, the remote controller’s control codes may overlap with those of another component. To differentiate the remote Unlocked controller’s control codes, you can change its ID to...

  • Page 84: Zone 2, Connecting Zone 2, Setting The Powered Zone 2

    Zone 2 Connecting Zone 2 With the Zone 2 function, you can enjoy one input source in the main room and a different source in another room. There are two ways to hook up your Zone 2 speakers: 1) Use another amp (receiver, integrated amp, or power amp) in Zone 2 and connect your Zone 2 speakers to it.

  • Page 85: Setting The Zone 2 Out

    Zone 2—Continued Use the Up and Down [ buttons to select “7. Hardware Setup,” and then press [Enter]. The Hardware Setup menu appears. 7. Hardware Setup 1. Remote Control 2. Zone2 3. Tuner 4. Analog Multich 5. HDMI Use the Up and Down [ ]/[ ] buttons to select “2.

  • Page 86: Using Zone 2

    Zone 2—Continued Press the [Setup] button. The setup menu closes. Note: This procedure can also be performed on the AV receiver by using its [Setup] button, arrow buttons, and [Enter] button. Using Zone 2 This section explains how to turn Zone 2 on and off, how to select an input source for Zone 2, and how to adjust the volume for Zone 2.

  • Page 87

    Zone 2—Continued Adjusting the Volume for Zone 2 Zone 2 Level On the remote controller, press Remote controller the [Zone 2] button, and then use the [Level–] and [Level+] buttons. AV receiver On the AV receiver, use the Zone 2 Level [ If your Zone 2 speakers are connected to a receiver or integrated amp in Zone 2, use its volume control to adjust the...

  • Page 88: And The Main Room

    Zone 2—Continued Using the 12V Triggers in Zone 2 and the Main Room When the AV receiver’s 12 V TRIGGER OUT A/B/C jack is connected to the 12 V trigger input on a connected component, you can specify whether or not a 12-volt trigger signal is output when that component is selected as the source for the main room, Zone 2, or either.

  • Page 89: And Multiroom Control Kits

    The IR emitter should be connected to the IR OUT jack, as shown below. Miniplug cable Signal flow IR receiver Connecting block Remote controller Signal flow IR receiver Connecting block DTR-5.8 IR emitter Remote controller Other component Signal flow Other component Remote control sensor Emitter Miniplug IR emitter...

  • Page 90: Controlling Other Components, Entering Remote Control Codes

    Controlling Other Components You can use the AV receiver’s remote controller (RC-683M) to control your other AV components, including those made by other manufacturers. This sec- tion explains how to enter the necessary remote control code for the component that you want to control (e.g., DVD player, TV, or VCR).

  • Page 91: Remote Control Codes For Integra Components Connected Via, Resetting Remote Mode Buttons

    AV receiver, and operate the component. If you want to control an Integra component by pointing the remote controller directly at it, or you want to control an Integra component that’s not connected via...

  • Page 92

    Controlling Other Components—Continued To control another component, point the remote controller at it and use the buttons explained below. (You must select the appropriate remote control mode first.) With some AV components, certain buttons may not work as expected, and some may not work at all. ■...

  • Page 93

    Specifications Amplifier Section Rated Output Power (FTC) All channels: 90 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven from 20 Hz to 20 kHz, with a maximum total harmonic distortion of 0.08% 105/110 watts minimum continuous power per channel, 8 ohm loads, 2 channels driven at 1 kHz, with a maximum total harmonic distortion of...

  • Page 94

    Troubleshooting If you have any trouble using the AV receiver, look for a solution in this section. If you can’t resolve the issue yourself, contact the dealer from whom you purchased. If you can’t resolve the issue yourself, try resetting the AV receiver before contacting the dealer from whom you purchased.

  • Page 95

    Troubleshooting—Continued The surround back speakers produce no sound • The surround back speakers are not used with all listen- ing modes. Select another listening mode (page 64). • Not much sound may be produced by the surround back speakers with some sources. •...

  • Page 96

    • Make sure to set the same ID on both the AV receiver and remote controller (pages 81 and 83). Can’t control other components • If it’s an Integra component, make sure that the cable and analog audio cable are connected properly. Connecting only an cable won’t work (page 39).

  • Page 97

    Troubleshooting—Continued Recording Can’t record • On your recorder, make sure the correct input is selected (e.g., digital or analog). Zone 2 There’s no sound • Only components connected to analog inputs can be played in Zone 2. Others The sound changes when I connect my head- phones •...

  • Page 98

    MEMO...

  • Page 99

    MEMO...

  • Page 100

    Integra Division of ONKYO U.S.A. CORPORATION 18 park Way, Upper Saddle River, N.J. 07458, U.S.A. Tel: 201-785-2600 Fax: 201-785-2650 http://www.integrahometheater.com Integra Division of ONKYO CORPORATION Sales & Product Planning Div.: 2-1, Nisshin-cho, Neyagawa-shi, OSAKA 572-8540, JAPAN Y0704-1 Tel: 072-831-8023 Fax: 072-831-8124 SN 29344500 (C) Copyright 2007 ONKYO CORPORATION Japan.

Comments to this Manuals

Symbols: 0

Latest comments:

×

Select the desired size and copy embed code

Copy your embed code and put on your site: