Integra DTR-5.6 Instruction Manual page 86

DTR-5.6.book Page 86 Thursday, September 22, 2005 5:07 PM
Troubleshooting —Continued
Remote Controller
The remote controller doesn't work
• Make sure that the batteries are installed with the cor-
rect polarity (page 7).
• Make sure that the remote controller is not too far
away from the AV receiver, and that there's no
obstruction between the remote controller and the AV
receiver's remote control sensor (page 7).
• Make sure you've selected the correct remote control-
ler mode (page 12).
• Make sure you've entered the correct remote control
code (page 79).
Can't control other components
• Make sure you've selected the correct remote control-
ler mode (page 12).
• If you've connected an
recorder, CD recorder, or next generation HDD-com-
patible component to the TAPE IN/OUT jacks, or an
Onkyo DS-A1 Remote Interactive Dock to the
VIDEO 3 IN jacks, for the remote controller to work
properly, you must set the input display to MD, CDR,
or HDD (see page 42).
• The entered remote control code may not be correct. If
more than one code is listed, try each one.
• If none of the codes work, use the Learning function
to learn the commands of the other component's
remote controller (page 82).
• With some AV components, certain buttons may not
work as expected, and some may not work at all.
• To control an Integra component that's connected via
, point the remote controller at the AV receiver. Be
sure to enter the appropriate remote control code first
(page 80).
• To control an Integra component that's not connected
via , or another manufacturer's component, point
the remote controller at the component. Be sure to enter
the appropriate remote control code first (page 79).
Can't learn commands from another remote
controller
• When learning commands, make sure that the trans-
mitting ends of both remote controllers are pointing at
each other.
• Are you trying to learn from a remote controller that
cannot be used for learning? Some commands cannot
be learned, especially those that contain several
instructions.
86
-capable Integra MD
Recording
Can't record
• On your recorder, make sure the correct input is
selected.
• To prevent signal loops and damage to the AV
receiver, input signals are not fed through to outputs
with the same name (e.g., TAPE IN to TAPE OUT,
VIDEO 1 IN to VIDEO 1 OUT, or VIDEO 2 IN to
VIDEO 2 OUT).
Others
The sound changes when I connect my head-
phones
• When a pair of headphones is connected, the listening
mode is set to Stereo, unless it's already set to Stereo,
Mono, or Direct, in which case it stays the same.
How do I change the language of a multiplex
source
• Use the "Multiplex" setting on the "Audio Adjust"
menus to select "Main" or "Sub" (page 61).
The functions don't work
• To use , you must make an
analog audio connection (RCA) between the compo-
nent and AV receiver, even if they are connected digi-
tally (page 34).
• While Zone 2 is on, the functions do not work.
The AV receiver contains a microcomputer for signal pro-
cessing and control functions. In very rare situations,
severe interference, noise from an external source, or
static electricity may cause it to lockup. In the unlikely
event that this happens, unplug the power cord from the
wall outlet, wait at least five seconds, and then plug it
back in again.
Onkyo is not responsible for damages (such as CD
rental fees) due to unsuccessful recordings caused by
the unit's malfunction. Before you record important
data, make sure that the material will be recorded cor-
rectly.
To reset the AV receiver to its factory defaults, turn
it on and, while holding down the [Video 1] button,
press the [Standby/On] button. "Clear" will appear
on the display and the AV receiver will enter
Standby mode.
Set the AV receiver to Standby before disconnecting
the power cord from the wall outlet.
connection and an