Related Manuals for King Canada Tru-Cut 8380
Summary of Contents for King Canada Tru-Cut 8380
-
Page 1: Instruction Manual
KING CANADA 10” COMPOUND SLIDING MITER SAW WITH TWIN LASER GUIDE *Enhanced Twin Laser Effect MODEL: 8380 INSTRUCTION MANUAL COPYRIGHT © 2008 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. -
Page 2: Warranty Information
LIMITED TOOL WARRANTY King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in materials. -
Page 3: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that for the specified tool can result in SERIOUS INJURY to the user - as well as damage to the tool. - Page 4 ADDITIONAL SAFETY INSTRUCTIONS FOR COMPOUND SLIDING MITER SAWS 1. WARNING: USE ONLY CROSS-CUTTING SAW BLADES. WHEN USING CARBIDE TIPPED BLADES, DO NOT USE 19. MAKE SURE blade is not contacting workpiece before switch is BLADES WITH DEEP GUILLETS AS THEY CAN DEFLECT turned on.
-
Page 5: Electrical Connections
ELECTRICAL CONNECTIONS WARNING! ALL ELECTRICAL CONNECTIONS MUST BE DONE BY A QUALIFIED ELECTRICIAN. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE MITER SAW DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! POWER SUPPLY 110V GROUNDED OUTLET WARNING: YOUR MITER SAW MUST BE CONNECTED TO A 110V,... -
Page 6: Unpacking And Assembly
UNPACKING & ASSEMBLY UNPACKING Due to modern mass production techniques, it is unlikely that your King Canada Power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. -
Page 7: Bench Mounting
ADJUSTMENTS BENCH MOUNTING The saw base has holes to facilitate bench mounting. 1. Fix the saw to a bench using 4 hex. bolts and hex. nuts. 2. If desired, you can mount the saw to a piece of 13mm or thicker plywood which can then be clamped to your work support or moved to other job sites and reclamped. - Page 8 ADJUSTMENTS SETTING THE BLADE SQUARE WITH THE TABLE 1. Make sure that the electrical plug is removed from the main power supply. 2. Push the saw head down to its lowest position, then pull and turn the head release knob to hold the saw head in the transport position. 3.
-
Page 9: Cutting Operations
ADJUSTMENTS & OPERATIONS USING THE TWIN LASER GUIDE SYSTEM The twin laser guide system is controlled by the laser guide push button switch (A) Fig.14 and will only turn on when the miter saw is plugged into a power source. Warning! Do not stare directly into the laser beams. -
Page 10: Bevel Cut
OPERATIONS When cutting wide workpieces, you should use the sliding action, unlock the slide lock knob (A) Fig.16. 1. Raise the saw head to its highest position and slide the blade towards you. 2. Hold the handle firmly and squeeze the trigger. Allow the blade to reach maximum speed. 3. - Page 11 REPLACING/INSTALLING BLADE REPLACING/INSTALLING BLADE DANGER! • Never attempt to use a blade larger than the stated capacity of the saw (10”). It will come into contact with the blade guards. • Never use a blade that is too thick to allow the outer blade flange to engage with the flats on the spindle.
-
Page 12: Maintenance
2 pan head screws. Carbon brush limit mark PARTS DIAGRAM & PARTS LISTS Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list. Figure 24...