Related Manuals for King Canada 8320MS
Summary of Contents for King Canada 8320MS
-
Page 1: Instruction Manual
8-1/4” DUAL COMPOUND MITER SAW WITH LASER GUIDE *Enhanced Laser Effect MODEL: 8320MS INSTRUCTION MANUAL COPYRIGHT © 2009 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC. -
Page 2: Warranty Information
LIMITED TOOL WARRANTY King Canada makes every effort to ensure that this product meets high quality and durability standards. King Canada warrants to the original retail consumer a 2-year limited warranty as of the date the product was purchased at retail and that each product is free from defects in materials. -
Page 3: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS VOLTAGE WARNING: Before connecting the tool to a power source (receptacle, outlet, etc.) be sure the voltage supplied is the same as that specified on the nameplate of the tool. A power source with voltage greater than that for the specified tool can result in SERIOUS INJURY to the user - as well as damage to the tool. - Page 4 ADDITIONAL SAFETY INSTRUCTIONS FOR DUAL COMPOUND MITER SAWS 1. WARNING: USE ONLY CROSS-CUTTING SAW BLADES. 23. PROVIDE adequate support to the sides of the saw table for WHEN USING CARBIDE TIPPED BLADES, DO NOT USE long workpieces. BLADES WITH DEEP GUILLETS AS THEY CAN DEFLECT AND CONTACT GUARD.
-
Page 5: Electrical Connections
Refer to Fig.2 for wire length and size. 8-10 10-12 12-16 FIGURE 2 TOOL SPECIFICATIONS Model......................................8320MS Voltage ......................................110V Input power....................................10.5 Amp. No load speed ..................................5,500 RPM Blade size..................................8-1/4” x 40 teeth Arbor size ......................................5/8” Miter table angles ..........................0 , 15 , 22.5... - Page 6 UNPACKING Due to modern mass production techniques, it is unlikely that your King Canada Power tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. Failure to do so could result in serious personal injury.
- Page 7 ADJUSTMENTS ADJUSTING FENCE EXTENSION This miter saw comes with a back fence with a fence extension (A) Fig.6 which slide outwards for additional back support for those long workpieces. Please note that during steep bevel cut operations to the right, this fence extension must be fully extended to not interfere with the motor housing or blade guard.
- Page 8 ADJUSTMENTS SETTING THE BLADE SQUARE WITH THE TABLE continued... If the saw blade angles away from the square, adjust as follows; 9. Loosen hex. nut (A) Fig.10 and unscrew set screw (B) to allow saw head adjustment. 10. Loosen the bevel lock knob (A)Fig.7 and pull the positive stop adjustment pin (C) Fig.10 outwards.
- Page 9 ADJUSTMENTS & OPERATIONS USING THE LASER GUIDE SYSTEM The laser guide system is controlled by the laser guide push button switch (A) Fig.13 and will only turn on when the miter saw is plugged into a power source. Warning! Do not stare directly into the laser beam. 1.
-
Page 10: Bevel Cut
OPERATIONS BEVEL CUT A bevel cut is made by cutting across the grain of the workpiece with the blade angled to the fence and miter table. The miter table is set at the 0º position and the saw head is set at an angle between 0 and 45 to the right or to the left. - Page 11 REPLACING/INSTALLING BLADE REPLACING/INSTALLING BLADE DANGER! • Never attempt to use a blade larger than the stated capacity of the saw (8-1/4”). It will come into contact with the blade guards and housing. • Never use a blade that is too thick to allow the outer blade flange to engage with the flats on the spindle.
-
Page 12: Maintenance
2 pan head screws. PARTS DIAGRAM & PARTS LISTS Refer to the Parts section of the King Canada web site for the most updated parts diagram and parts list. Figure 21...