Advertisement
Available languages
Available languages
4. Installing your child seat (rearward facing) in front seat
IMPORTANT
4a
seat belt.
The child seat has an adjustable support leg
more reclined the seat must be. The larger the child the more upright the seat
must be.
The larger the child the more upright the seat must be. To change the position
4b
(if required) slide the support leg out until it engages in the desired position.
To slide the support leg in push the two support leg adjuster buttons and pull
up the support leg
Push the vehicle front seat back to accommodate the child seat ensuring that
any passenger directly behind will still be able to sit in a comfortable position.
The larger your child, the more upright the sitting position should be.
Place the child seat rearward facing and push firmly into the car seat
4c
IMPORTANT
close to the windscreen.
Extend the footprop fully by pressing the two release Buttons. Make sure
that the footprop tether brackets are facing forwards and that the straps
are not twisted. Lower the footprop and adjust the height so that it is within
approximately 30mm of the floor
page of this manual to get the correct distance from the footprop to the floor.
4d
4e
3
– The child seat
MUST
only be used with a lap and diagonal
(dia
4a). The smaller the child the
(dia
4b). Make sure the support leg is engaged firmly.
–
DO NOT
rest the back of the child seat on the dashboard or
(dia
4c). Use the ruler printed on the back
Slide the loop ends of the tether straps
between the front car seat and back as
shown
(dia 2d &
hook ends of the tether straps around
the outside of the car seat and feed
through the loops
2
of the tether straps onto the fixing rings
on the back of the child seat
Provisionally tighten the tether straps by
pulling the loose ends downwards
2
4
4f
4g
(dia
4c).
4h
4j
dia
2e). Bring the
. Snap the hooks
.
3
.
4
Slide the loop ends of the tether straps between the front car seat and back
as shown
(dia
4d). Bring the buckle ends of the tether straps around the
outside of the car seat and feed through the loops
under the seat. Snap the buckles of the tether straps onto the tongues on the
sides of the child seat
3
. Provisionally tighten the tether straps by pulling the
loose ends downwards
4
.
Pull off sufficient lap and diagonal belt
(approx.600 –
off arm on the side opposite the seat belt buckle. Pull back the child seat cover
to reveal the crotch strap. Feed the belt through the lock-off belt guide and seat
shell slot
(dia
4g), up on to the top face of the seat base, behind the crotch
strap
(inset)
and down through the slot on the other side of the child seat.
Open the other lock-off arm, feed the seat belt under the lock-off arm and
attach the tongue into the buckle
(dia
4h).
Pull all of the seat belt slack through the
4i
child seat ensuring the seat belt is not
twisted
(dia
as possible, close the lock-off arms on
BOTH
sides of the seat ensuring that
they click into place.
If the buckle now lies in the position
marked as wrong with a
belt cannot be correctly tightened
try another seating position in the car.
Finally tighten the tether straps by pulling
the loose ends downwards
until the footprop touches the floor. The
4k
footprop must rest on a solid floor – not
on lids of storage boxes or similar.
Once firmly strapped in, test the child
seat by trying to move it back and forth
and side to side. If it seems loose, you
must reinstall until firmly installed.
DO NOT
seat on the dashboard or close to the
windscreen.
9-25 kg
2
. Slide the buckle ends
900mm). Open the lock-
4i). When the belt is as tight
and the seat
(dia
4j),
(dia 4k)
rest the back of the child
Advertisement
