Table of Contents
Related Manuals for CDA HVG620
Summary of Contents for CDA HVG620
- Page 1 HVG620 & HVG720 Gas Hob Manual for Installation, Use and Maintenance Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...
- Page 2 Appliance information: Please enter the details on the appliance rating plate below for reference, to assist CDA Customer Care in the event of a fault with your appliance and to register your appliance for guarantee purposes. Appliance Model Serial Number...
- Page 3 safety (LVD) and Electromagnetic interference compatibility (EMC). Parts intended to come into contact with food conform to EEC/89/109. IMPORTANT INFORMATION FOR CORRECT DISPOSAL OF THE PRODUCT IN ACCORDANCE WITH EC DIRECTIVE 2002/96/EC. At the end of its working life, the product must be taken to a special local authority waste collection centre or to a dealer providing appliance recycling services.
-
Page 4: Using Your Hob
• This hob (Class 3) has been designed for use only as a cooking appliance. Any other use (e.g. heating rooms) should be considered incorrect and potentially dangerous. • These instructions are valid only for the countries of destination, the symbols of which appear on the cover and on the appliance . - Page 5 Gas burners: Gas flow to the burners is controlled by the control knobs (5, 6, 7 and 8 or 14, 15, 16, 17 and 18 on the diagram above). There are 3 positions shown on the control panel. Turning the control knob to the positions shown below achieves the following: Closed (OFF position) Maximum position: Provides fast boiling function...
-
Page 6: Igniting The Burners
Igniting the Burners The hob is fitted with a flame failure device. Flame failure devices operate by shutting off the supply of gas to the burner in the event that the flame is extinguished accidentally. To ignite the burners, follow these instructions: 1. -
Page 7: Efficient Use Of Your Hob
• If a burner does not ignite, or turns off accidentally, turn the control knob to the ‘off’ position, and wait for one minute before attempting to reignite the burner. • If the burner does not ignite, repeat the ignition process with the burner at the minimum position. -
Page 8: Care And Maintenence
Care and Maintenence As the hob has a glass surface, you should use a nonabrasive cleaner. Any abrasive cleaner (including Cif) will scratch the surface and could erase the control panel markings. Glass can be effectively cleaned by simply using a dilute solution of water and mild detergent and drying to a shine with a clean cloth. - Page 9 Rapid 218.8 214.8 Triple ring/wok Total rated gas input : 7.5kW (HVG620), 11.3kW (HVG720) Mains electrical voltage: 230 – 240Vac, 50Hz Total rated electrical consumption: 1.1W If your Hob is not working 1. Check that the mains supply has not been switched off.
-
Page 10: Mains Electricity Connection
Mains Electricity Connection THIS APPLIANCE MUST BE CONNECTED TO THE MAINS SUPPLY BY A COMPETENT PERSON, USING FIXED WIRING VIA A DOUBLE POLE SWITCHED FUSE SPUR OUTLET AND PROTECTED BY A 3A FUSE. We recommend that the appliance is DOUBLE POLE SWITCHED connected by a qualified electrician, FUSE SPUR OUTLET who is a member of the N.I.C.E.I.C. -
Page 11: Gas Supply Requirements
UK and Ireland. The installation must comply with the Gas Safety (installation and use) Regulations 1984. • The CDA Group Ltd is not legally able to provide any assistance in the installation of gas appliances except to Gas Safe registered installers. Any Gas Safe registered fitter requiring help must provide their name, address and registration number. - Page 12 recovery scavenging system • The connection to the gas supply must comply with all current regulations in force. • We are not legally able to offer advice on the installation of gas appliances to non Gas Safe registered personnel. Ventilation All rooms require a window or equivalent (e.g.
-
Page 13: Natural Gas To Lpg Conversion
Natural Gas to LPG Conversion This hob can be converted from natural gas to propane operation at a nominal inlet pressure of 37mbar, or butane operation at a nominal inlet pressure of 28/30mbar. This conversion must only be carried out by a competent person (i.e. -
Page 14: Lpg To Natural Gas Conversion
4. Turn the controls to maximum position then quickly to the minimum position - make sure the flame does not extinguish. 5. Replace the knobs. LPG to Natural Gas Required: Conversion • 7mm AF nut spinner • Replacement injectors This hob can be converted from •... -
Page 15: Fitting The Hob
Fitting the Hob Unpacking the hob: Take care not to lose or mishandle any 15mm parts. Ventilation slot > 30mm Fig.5 Fitting position of the hob: This appliance must be installed a minimum of 50mm from any back wall and a minimum of 150mm away from any adjacent vertical surfaces, e.g. - Page 16 Notes: • Do not position this appliance above a refrigeration unit. The heat generated may cause the refrigeration unit to fail. • This appliance is designed to be installed into cabinet units capable of withstanding temperatures 65°C above ambient or greater (typically 80-90°C).
-
Page 17: How To Install The Hob
How to Install the Hob How to install the hob: Overall hob dimensions: HVG620 = 580mm (W) x 500mm (D) HVG720 = 700mm (W) x 510mm (D) Worktop cut-out dimensions: 557mm (W) x 477mm (D) 1. Make the required hole in the worktop. Note that before doing this, check the instructions supplied with any cooker hood to ensure that you will have the required clearance. - Page 20 Please contact our Customer Care Department, or for Service on the details below. Customer Care Department • The Group Ltd. • Harby Road • Langar • Nottinghamshire • NG13 9HY T : 01949 862 012 F : 01949 862 003 E : service@cda.eu W : www.cda.eu...