Star Trac Leg Curl Owner's Manual page 12

6. Install the Seat, Back and Leg
Cushions
Hold the seat cushion (17) in place on the main
frame (2). Secure the seat cushion to the main
frame and seat cushion support (8) using four
screws (67) and washers (78). Tighten the
screws securely.
Hold the back cushion (26) in place on the back
cushion support (7). Secure the back cushion to
the back cushion support using one screw (69),
two screws (67) and three washers (78).
Tighten the screws securely.
Install one large collar (34), one leg cushion
(19) and one large collar (34) on the leverage
arm actuator (10). Secure the leg cushion in
place on the leverage arm actuator using one
screw (66), spring washer (79), washer (78)
and collar (35). Tighten the screw securely.
Install one large collar (34), one leg cushion
(19) and one large collar (34) on the lap cush-
ion support (13). Loosen the two setscrews (57)
in the leg cushion retainer (21). Install the leg
cushion retainer on the lap cushion support,
and tighten the two setscrews (57).
7. Install the Weight Stack Shrouds
NOTE: It is necessary to flex the lower
shrouds (38, 39) slightly to engage the mat-
ing grooves in the weight stack frame (1).
Slide the lower front shroud (39) into the mat-
ing grooves in the weight stack frame (1). Slide
the lower rear shroud (38) into the mating
grooves in the weight stack frame.
Install one tapped hole nut (52) onto each of
the six upper shroud mounting tabs on the
weight stack frame (1).
Hold one upper shroud (40) in position against
the weight stack frame (1), and secure the
shroud to the frame using three screws (65)
and washers (77).
Repeat for the remaining upper shroud (40).
12
34
19
34
26
7
57
78 69
78 67
67
78
13
17
2
78
10
67
78
8
78
67
78
67
34
34 67
78
19
79
66
35
65
77
77
40
52
65
77
1
52
52
38
77
65
52
77
77
65
STAR TRAC INSTINCT LEG MACHINES O
WNER
5. Install the Handgrips and Cushion
Brackets
Hold the handgrips (5) in position on the under-
side of the main frame (2) and align the five
57
drilled holes in the handgrips with the mating
holes in the main frame. Secure the handgrips to
21
the main frame using two screws (81), four wash-
ers (88), two lock nuts (85), one screw (75), one
spring washer (89) and one washer (88). Tighten
the attaching parts securely.
Hold the seat cushion support (8) in place on
the main frame (2). Secure the seat cushion
support to the main frame using four screws
(72), washers (88) and lock nuts (85). Tighten
the nuts securely.
Hold the back cushion support (7) in place on
the seat post (6) (factory installed). Secure the
back cushion support to the seat post using
two screws (77), four washers (88) and two lock
nuts (85). Tighten the nuts securely.
6. Install the Seat, Back and Leg
Cushions
Hold the seat cushion (21) in place on the main
frame (2). Secure the seat cushion to the main
frame and seat cushion support (8) using four
screws (76) and washers (88). Tighten the
screws securely.
Hold the back cushion (31) in place on the back
cushion support (7). Secure the back cushion to
the back cushion support using one screw (78),
two screws (76) and three washers (88).
Tighten the screws securely.
Install one collar (42), one leg cushion (24) and
65
one collar (42) on the leverage arm actuator
40
(10). Secure the leg cushion in place on the
leverage arm actuator using one screw (75),
spring washer (89), washer (88) and collar (43).
Tighten the screw securely.
39
Install one collar (42), one leg cushion (24) and
one collar (42) on the lap cushion support (15).
Loosen the two setscrews (66) in the collar
(26). Install the collar on the lap cushion sup-
port, and tighten the two setscrews (66).
' M STAR TRAC INSTINCT LEG MACHINES O
S ANUAL
7
88
77
88
85
2
75
42
31
7
88
15
2
88
10
76
8 88
76
42
42
24
43
' M
WNER S ANUAL
85
88
85
72
6
8
88
85
88 85
5
88
81
88
88
88
89 81
24
42
66
26
66
88 78
88 76
76
21
88
88
76
76
88
89
75
25