Instructions For Rcsitea (Sddvtcs Series) - Vermont Castings SDDVTEB Homeowner's Installation And Operating Manual

Instructions for RCSITEA
SDDVTCS Series
CAUTION: The RCSITEA is only certified for use on
vented heater rated equipment.
This remote control system provides a safe, reliable
and user-friendly remote control for millivolt valve gas
appliances, blower speed and flame height adjustment.
The system can be manually or thermostatically turned
on and off with the transmitter.
Carefully inspect the contents for shipping damage. If
any parts are missing or damaged, immediately contact
your dealer. Do not attempt to install any part of the kit
unless all parts are in good condition. Refer to instruc-
tions provided with the kit for complete installation
instructions.
WARNING: Make sure 10V AC fan and SIT valve are
correct. If not wired correctly, damage to receiver could
result. Make sure the wires do not contact the applianc-
es any place other than at the terminals. Exposure to
temperatures higher than 50°F (105°C) may cause the
receiver to malfunction and cause possible fire hazard.
Remote Transmitter
Install Batteries
The remote transmitter uses three
(3) "AAA" batteries.
1. Press down the battery door tab
and pull out to remove the bat-
tery door. (Fig. 57)
. Install the batteries as indicated
on transmitter.
3. Close the battery door by snap-
ping in place.
4. When three (3) batteries are
installed, the transmitter will
initialize for 10 seconds and then
is ready for use.
5. The batteries should be replaced at least once every
six (6) months or when the low battery indicator is
displayed.
Setting Privacy (DIP) Switch on Receiver and Trans-
mitter
The remote receiver and transmitter privacy (DIP)
switches are preset at the factory. In the event of activa-
tion or interference from other nearby transmissions,
reset the code using the following procedure:
1. Slide the code switches on the transmitter and re-
ceiver to choice of ON or OFF position. Switches #1,
#, #3 and #4 are preset to "ON" for both the trans-
mitter and receiver. (Fig. 58)
30004968
Stardance® Direct Vent/Natural Vent Gas Heater
Battery
Door
Tab
Fig. 57 Bat-
tery door tab.
ST1088
RCSITE battery tab
. The switches on the transmitter and receiver must
match in order for the system to work.
3. To check, press either the ON or OFF button on the
transmitter and the receiver indicator light will blink.
If not, repeat Step .
4. The system is now ready to operate.
NOTE: Refer to optional 6 Hour Shutdown.
WARNING: Do not use two () or more remote
control systems in the same area with the
same dip switch settings, they will commu-
nicate with each other. This may cause the
appliances to malfunction.
Dip Switch
(Default)
ON DIP
Transmitter
Fig. 58 The switches on the transmitter and receiver must
match.
ST1089
RCSITE dip switches
Reset Button
The reset button can be used to reset the transmitter
if transmitter is not working properly. The reset button
is located behind the battery door cover in the lower
left corner of battery compartment. Using a paper clip,
press the reset button and the transmitter will reset and
initialize for 10 seconds before it can be used.
Operation
Transmitter
General
The RCSITEA Remote Control
has two () operating modes:
Manual and Thermostatic. The
control system can be set to
temperature ranges between 45°F
and 90°F. The blower speed and
flame height can be adjusted in
either the manual or thermostatic
mode.
The transmitter will operate the
remote receiver from 1 foot to a
maximum of 30 feet. The distance
is reduce when batteries are low
or when the receiver is inside a
metal enclosure.
ON DIP
Receiver
ST1089
ON
AUTO
FAN
FLAME
OFF
AMBIENT
Fig. 59 RCSITEA
remote transmitter.
ST1090
RCSITE remote
33