Control (Cpu) Board - Life Fitness 9500 Series Service Manual

Hr and telemetry equipped treadmills
Hide thumbs Also See for 9500 Series:
Table of Contents

Advertisement

Life Fitness Model 9500 Series HR and Telemetry Equipped Treadmills
How To... REMOVE AND REPLACE THE CONTROL (CPU) BOARD (Continued)
Tools Required: Standard screwdriver
Step 6
Disconnect the seven CONNECTORS from the worn CONTROL BOARD, taking note of their locations.
Step 7
With a standard screwdriver, loosen and remove the six SCREWS from the CONTROL BOARD and remove the
BOARD and BOARD SPACERS.
Step 8
While holding the new CONTROL BOARD in place, reinsert the six SCREWS and BOARD SPACERS and tighten
with a standard screwdriver.
Step 9
Reconnect all seven CONNECTORS to the new CONTROL BOARD. Slide the CONTROL BOARD SHELF in place
and push up on the three PLASTIC RIVETS, snapping them in place.
Step 10
To lower the unit, plug the LINE CORD into the electrical outlet and power unit ON at the ON/OFF switch. Press the
START key, when the unit is back at a zero percent incline, press the CLEAR key.
Step 11
Find the new CONTROL BOARD software version by pressing 919, ENTER. Press the Random and Fit Test
Program lights to ON. The DISPLAY will scroll through the stats, note the control and logic versions. Refer to chart
for code combination needed to reset the WAX DELAY and ENTER wax counts recorded in step 1.
NOTE: THE WAX DELAY AND WAX COUNT INFORMATION IS VITAL FOR PROPER OPERATION AND LIFE
MODEL
REPLACE BELT AND DECK
TR9500HR
Reset Stats
*Software Version
Press 101,
control
ENTER. Hill,
14.9 or earlier
Random,
Manual, and Fit
logic
Test program
13.0 or earlier
lights ON. Press
#1 key, then
CLEAR to exit.
DO NOT CLEAR
control
STATS
15.0 & later
logic
15.0 & later
* To Find Software Version Press 919, ENTER. Random and Fit Test Program lights ON. Display will scroll through to
control and logic.
** To Find Previous Wax Counts Press 919, ENTER. Fit Test Program light ON.
*** Previous Wax Counts must be entered manually. Diagnostic 919, ENTER. Unplug wax pump and fire pump until count is correct.
NOTE: Treadmills with software earlier then 15.0 control and logic. To get the wax count correct, go into the diagnostics, unplug wax
pump at wax pump connection and manually reset wax counts. Or refill wax and reset stats to 100% FULL.
OF THE STRIDING BELT AND DECK.
Turn Wax Delay ON
Press 101, ENTER.
Press 101, ENTER.
Hill, Random, and Fit Test
Hill, Random, and Fit Test
program lights ON.
program lights ON.
(Display will scroll through
(Display will scroll through
to WAX DELAY OFF) Press
to WAX DELAY ON) Press
Speed (up or down) key to
Speed (up or down) key to
toggle WAX DELAY ON.
toggle WAX DELAY OFF.
Press 8228, ENTER.
Press 8228, ENTER.
Press #1 New Belt/Deck
Press #1 New Belt/Deck
Press #2 New CPU,
Press #2 New CPU,
Press #3 Belt/Deck/CPU.
Press #3 Belt/Deck/CPU.
If #2 or #3 are used enter
If #2 or #3 are used, enter
**previous Wax Counts.
**previous Wax Counts.
REPLACE CPU
REFILL WAX BAG TO FIRE WAX PUMP
Turn Wax Delay OFF
Press 125, ENTER
Display will read
"FILL WAXER
FULL"
Press ENTER.
Press 5125, ENTER
(Display will read)
"FILL WAXER
FULL"
Press ENTER.
Service only
Press 919, ENTER
Fit Test program
light ON, ENTER
Press 7373, ENTER
27

Hide quick links:

Advertisement

Table of Contents
loading

Table of Contents