Advertisement
16. Locate the L
A
EFT
CCESSORY
the top of the L
U
EFT
Secure the accessory tray to the L
using four S
(21). Repeat the procedure for the R
CREWS
A
T
(12) and R
CCESSORY
RAY
17. Tighten all U
B
PRIGHT
18. Replace the M
C
OTOR
to the F
(C) using the four previously removed S
RAME
(D). Tighten the S
CREWS
S
.
CREWS
19. Replace the F
G
RONT
F
(C) using the four previously removed S
RAME
Tighten the S
securely. Do not overtighten the S
CREWS
20. Locate one S
G
CREW
into the square hole located above the top inside mounting bolt
of the R
U
IGHT
PRIGHT
G
and L
U
ROMMET
EFT
21. Locate one L
U
OWER
U
C
at the bottom notch of the R
PRIGHT
OVER
making sure the top lip of the U
the outside notch of the R
C
to the R
U
OVER
IGHT
S
securely. Do not overtighten the S
CREW
cedure for the L
U
EFT
22. Locate the U
P
PRIGHT
each of the two access holes located on the lower outside of the
L
and R
U
EFT
IGHT
PRIGHTS
23. Locate and press the H
H
(3). Be sure the H
ANDLEBARS
24. Using two S
(16) each, attach the two R
CREWS
C
(14) to the F
APS
RAME
securely. Do not overtighten the S
25. The treadmill striding belt must be "walked-in" for five
minutes after assembly is complete.
Plug the treadmill into an appropriate outlet. Turn the treadmill on
at the on/off switch. Select QUICK START from the console.
Increase the speed to 3 mph (4.8 km/h). Start walking in the
front left corner of the walking surface and drift to the back,
move to the center of the deck and walk towards the front, and
finally walking to the right corner and drifting to the back.
Continue pattern for five minutes.
26. Refer to the specific treadmill's Operation Manual for power
requirements, proper line cord routing, and other critical product
information before connecting the treadmill to a power source
T
(11). Carefully slide the tray into
RAY
(1) as shown until fully seated.
PRIGHT
T
M
EFT
OP
OUNTING
T
M
IGHT
OP
OUNTING
securely.
OLTS
(E) and secure the M
OVER
securely. Do not overtighten the
(B) and secure the F
RILL
(18). Insert the S
ROMMET
(2). Repeat for the remaining S
(1).
PRIGHT
C
(10). Position the L
PRIGHT
OVER
IGHT
C
PRIGHT
OVER
U
. Secure the U
IGHT
PRIGHT
using one S
PRIGHT
CREW
CREW
(1) and remaining U
PRIGHT
(25). Insert one U
LUGS
PRIGHT
(1 & 2).
C
(13) over the ends of the
ANDLEBAR
APS
C
ANDLEBAR
APS
(C) as shown. Tighten the S
.
CREWS
P
(H)
LATE
IGHT
P
(J).
LATE
C
OTOR
OVER
CREWS
G
to the
RONT
RILL
(A).
CREWS
.
CREWS
G
CREW
ROMMET
CREW
OWER
U
(2)
PRIGHT
is engaged under
PRIGHT
(16). Tighten the
. Repeat the pro
C
.
PRIGHT
OVER
P
into
LUG
are fully seated.
F
E
EAR
RAME
ND
CREWS
7
Advertisement
