Summary of Contents for Life Fitness LCD Entertainment Ready
Page 1
LCD Entertainment Ready I n s t a l l a t i o n I n s t r u c t i o n s...
Page 3
LIFE FITNESS ASIA PACIFIC LTD Room 2610, Miramar Tower 132 Nathan Road Tsimshatsui, Kowloon HONG KONG Telephone: (+852) 2891.6677 FAX: (+852) 2575.6001 LIFE FITNESS ATLANTIC BV LIFE FITNESS BENELUX Bijdorpplein 25-31 2992 LB Barendrecht THE NETHERLANDS Telephone: (+31) 180.646.666 FAX: (+31) 180.646.699...
Page 4
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a resi- dential installation.
• Never operate a Life Fitness product if it has a damaged power cord or electrical plug, or if it has been dropped, damaged, or even partially immersed in water. If this occurs, contact Life Fitness Customer Support Services as out- lined in Service Contacts at the end of this manual.
Page 7
Toujours suivre les instructions sur le produit pour s'assurer de son fonctionnement adéquat. • Ne jamais insérer aucun objet dans les ouvertures du produit Life Fitness. Si un objet tombe à l'intérieur du produit Life Fitness, le débrancher et extraire l'objet soigneusement pendant que l'appareil est débranché. S'il est impossi- ble d'atteindre l'objet, communiquer avec le service à...
NSTALLATION Note to the CATV Installer: This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the ground- ing system of the building as close to the point of cable entry as practical.
ODELS READMILLS : Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench OOLS EQUIRED : (1) Main Bracket Cap, (1) Grommet ARTS Turn off the treadmill and unplug it from the power outlet. Remove the six SCREWS securing the MOTOR COVER. Remove the MOTOR COVER and set it and the screws aside.
Page 10
SCREW (22) on each side. NOTE: Life Fitness recommends aligning and securing the TV at the lowest side holes (D) as shown. 26. Plug in the treadmill and power on the treadmill and TV. Refer to the Owners Manual for proper TV setup.
Page 11
95X C ODELS ROSS RAINERS : Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench OOLS EQUIRED : (1) Main Bracket Cap, (1) Grommet ARTS 1. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (--). Interlock the remaining FASTENER STRIP to the installed FASTENER STRIP.
Page 12
21. Align the LOWEST SIDE HOLES on the TV BRACKETS (-- & --). Secure the TV BRACKET into proper position using one SCREW (--) on each side. NOTE: Life Fitness recommends aligning and securing the TV at the lowest side holes ???? 22.
Page 13
95C U ODELS PRIGHT IFECYCLE : Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench OOLS EQUIRED : (1) Main Bracket Cap, (1) Grommet ARTS 1. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (-- ).
Page 14
21. Align the LOWEST SIDE HOLES on the TV BRACKETS (-- & --). Secure the TV BRACKET into proper position using one SCREW (-- ) on each side. NOTE: Life Fitness recommends aligning and securing the TV at the lowest side holes ???? (--) as shown.
Page 15
95R R ODELS ECUMBENT : Phillips Screwdriver, Metric Allen Set, M16 & M17 Wrench OOLS EQUIRED : (1) Main Bracket Cap, (1) Grommet ARTS 1. Remove the protective liner from one of the provided FASTENER STRIPS. Attach the fastener strip to the bottom of the POWER BLOCK (--). Interlock the remaining FASTENER STRIP to the installed FASTENER STRIP.
Page 16
21. Align the LOWEST SIDE HOLES on the TV BRACKETS (-- & --). Secure the TV BRACKET into proper position using one SCREW (--) on each side. NOTE: Life Fitness recommends aligning and securing the TV at the lowest side holes ???? 22.
ODELS UMMIT RAINER : Metric Hex Key Set, Side Cutters, T-45 Torx Wrench OOLS EQUIRED Remove the CONSOLE SUPPORT TOP CAP (a). Remove the two SCREWS (b) securing the CONSOLE SUPPORT COVER (c). Remove the CONSOLE SUPPORT COVER and set it and the SCREWS aside. Remove the four SCREWS (d) securing the DISPLAY CONSOLE (e).
Page 18
NSTALLATION , 93C, 90C U ODELS PRIGHT : Metric Hex Key Set, Side Cutters OOLS EQUIRED NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE and ACCESSORY TRAY as described in the Assembly Instructions. Locate the SPACER (a). With the SPACER oriented as shown, feed all the CONSOLE CONNECTORS, POWER CORD, and COAXIAL CABLE through the large center hole in the SPACER.
Page 19
10. Attach the ADAPTER BRACKET (AA) to the ENTERTAINMENT CONSOLE (k) to the using four SCREWS (BB). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. Attach the ENTERTAINMENT CONSOLE to the UPPER MOUNTING PLATE (m) using four SCREWS (n) and WASHERS (o).
Page 20
NSTALLATION , 93R, 90R R ODELS ECUMBENT : Metric Hex Key Set, Side Cutters OOLS EQUIRED NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the Assembly Instructions. Locate the SPACER (a). With the SPACER oriented as shown, feed all the CONSOLE CONNECTORS, POWER CORD, and COAXIAL CABLE through the large center hole in the SPACER.
, 93S, 90S S ODELS TAIRCLIMBERS : Metric Hex Key Set, Side Cutters OOLS EQUIRED NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE and ACCESSORY TRAY as described in the Assembly Instructions. Locate the REMOTE CONTROL (a). Configure the REMOTE CONTROL for a VERTI- CAL (C-V) installation.
NSTALLATION , 93X, 90X C ODELS ROSS Metric Hex Key Set , Side Cutters, T-45 Torx Wrench OOLS EQUIRED NOTE: Proceed with the following steps before attaching the DISPLAY CONSOLE as described in the Assembly Instructions. Do not install the left BULLHORN and BULLHORN COVER. Do not install the ACESSORY TRAY. If the left bullhorn has been installed, follow steps 1 &...
, 90T T ODELS READMILLS : Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters OOLS EQUIRED NOTE: Proceed with the following steps immediately after attaching the DISPLAY CONSOLE as described in the Assembly Instructions. Do not install the ACCESSORY TRAYS or PUSH RIVETS. Remove the nine SCREWS (a) from the rear of the console securing the FRONT CONSOLE (b) to the REAR CONSOLE (c).
Page 24
NSTALLATION 13 Locate the COAXIAL COUPLER (u). Remove the RETAINING NUT (v) and two WASHERS (w & x) from the COUPLER. Insert the COUPLER into the large D-SLOT located at the front of the MOTOR PAN (y). Secure the COUPLER using the two WASHERS and RETAINING NUT previ- ously removed.
, 95T , 93T T ODELS READMILLS : Standard Screwdriver, Phillips Screwdriver, Metric Hex Key Set, Side Cutters OOLS EQUIRED NOTE: Proceed with the following steps immediatle after attaching the DISPLAY CONSOLE as described in the Assembly Instructions. Do not install the ACCESSORY TRAYS. Locate the REMOTE CONTROL (a).
Page 26
NSTALLATION Attach the ADAPTER BRACKET (n) to the ENTERTAINMENT CONSOLE (o) to the using four SCREWS (p). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS. Attach the ENTERTAINMENT CONSOLE to the MOUNTING BRACKET (q) using four SCREWS (r) and WASHERS (s). Tighten the SCREWS to 6-8 in-lbs. Do not overtighten the SCREWS.