Advertisement
6. Locate both H
ANDLEBARS
over each H
ANDLEBAR
should face outward.
7. with the bend of one H
treadmill, insert the H
B
(L) as shown. Be sure the handlebar mounting holes are
RACKET
aligned. Repeat for the left side H
8. Locate the E
F
™
RGO
F
C
with the plastic C
RONT
ROSSBAR
forward as shown. Locate and slide the L
S
(5 & 6) over the corresponding ends of the E
HROUDS
C
as shown. Slide the L
ROSSBAR
S
towards the center of the E
HROUDS
shown. Note: Be careful not to damage any wire harnesses that
may be leading from the ends of the E
9. Install one F
C
RONT
ROSSBAR
over either end of the E
grommets just over the end brackets to meet the overmolding.
Note: Be careful not to damage any wire harnesses that may be
leading from the ends of the E
10. Position the right end of the E
large access hole on the inside of the R
B
(L). Align the E
RACKET
with those in the R
IGHT
using two B
(19), from the inside of the treadmill, and N
OLTS
(22). Tighten the B
OLTS
under the R
U
IGHT
PRIGHT
securely.
11. Position the left end of the E
large access hole on the inside of the L
B
(N). Feed the H
RACKET
hole downward out the bottom of the L
B
.
RACKET
Align the crossbar mounting holes with those in the L
H
B
and secure using two B
ANDLEBAR
RACKET
inside of the treadmill, and N
Insert one S
(17) from under the L
CREw
B
. Tighten the S
RACKET
Note: Be careful not to pinch the H
equipped) when assembling the E
(4) to the L
U
EFT
PRIGHT
Feed the H
R
EART
ATE
L
U
(1).
EFT
PRIGHT
(3). Slide one H
ANDLEBAR
. The groove of the H
ANDLEBAR
(3) directed to the outside of the
ANDLEBAR
into the R
ANDLEBAR
IGHT
.
ANDLEBAR
C
(4) and position the E
RONT
ROSSBAR
(M) facing upward and
OvER
EFT
and R
EFT
IGHT
F
RGO
RONT
F
RGO
RONT
G
(26), rounded end first,
ROMMET
F
C
RGO
RONT
ROSSBAR
F
C
RGO
RONT
ROSSBAR
F
C
RGO
RONT
ROSSBAR
U
IGHT
F
C
RGO
RONT
ROSSBAR
U
H
B
PRIGHT
ANDLEBAR
RACKET
securely. Insert one S
H
B
. Tighten the S
ANDLEBAR
RACKET
F
C
RGO
RONT
ROSSBAR
U
EFT
PRIGHT
R
C
(O) into the access
EART
ATE
ABLE
U
EFT
PRIGHT
OLTS
(22). Tighten the B
UTS
U
EFT
PRIGHT
securely.
CREw
R
EART
ATE
F
RGO
RONT
H
B
.
ANDLEBAR
RACKET
C
(O) upward through the top of the
ABLE
G
(27)
ROMMET
G
ROMMET
U
H
PRIGHT
ANDLEBAR
RGO
O
and R
I
IGHT
NSIDE
F
22
RGO
RONT
I
H
NSIDE
ANDLEBAR
C
as
ROSSBAR
1
C
(4).
ROSSBAR
(4). Position the
(4).
(4) near the
H
PRIGHT
ANDLEBAR
M
H
OUNTING
OLES
and secure
UTS
(17) from
CREw
CREw
(4) near the
H
ANDLEBAR
H
ANDLEBAR
U
EFT
PRIGHT
(19), from the
securely.
OLTS
H
ANDLEBAR
C
(o) (if
ABLE
C
ROSSBAR
M
6
26
5
26
19
4
N
2
3
17
Note: the cLst model
does not have an
activity Zone on the
ergo™ front crossbar.
L
22
3
17
5
Advertisement
