Advertisement
DO NOT DISCARD THE SHIP KIT LOCATED ON TOP OF THE DECK AND BELT. ALL NECESSARY COMPONENTS
NEEDED TO COMPLETE THE INSTALLATION ARE LOCATED IN THE SHIP KIT.
NE JETEZ PAS LE KIT D'EXPÉDITION PLACÉ SUR LE DESSUS DU PLATEAU ET SUR LE TAPIS. IL CONTIENT
TOUS LES ÉLÉMENTS NÉCESSAIRES POUR L'INSTALLATION.
Check the belt edge under the treadmill to verify the belt does not interfere with lifespring brackets and the belt is
properly set within the belt guides.
Remove the four S
1.
CREwS
to the F
(C). Remove the F
RAME
2. Remove the four S
CREwS
Lift and remove the M
3. Locate the L
U
EFT
PRIGHT
the belt and deck with the notched end near the L
M
B
(F).
OUNTING
RACKET
4. Unwrap the M
w
AIN
IRE
U
M
B
PRIGHT
OUNTING
H
through the L
ARNESS
U
upwards and position the notched end of the L
PRIGHT
U
over the L
PRIGHT
EFT
L
T
M
P
EFT
OP
OUNTING
L
U
down over the L
EFT
PRIGHT
B
and pre-installed B
RACKET
the F
(C). Secure the L
RAME
M
B
using two B
OUNTING
RACKET
Use one B
and w
OLT
U
and one B
PRIGHT
OLT
L
U
. Leave the B
EFT
PRIGHT
Note: Be careful not to damage the M
when routing it through the L
sliding the L
U
eft
priGHt
B
(f).
racket
Note: Be sure the pre-installed washer is on the outside
of the L
U
(1) when sliding it down to rest on
eft
priGHt
the f
(c).
raMe
5. Locate the R
U
IGHT
PRIGHT
P
(J) directed forward, slide the R
LATE
over the R
U
IGHT
PRIGHT
installed B
and w
OLT
Secure the R
U
IGHT
PRIGHT
B
using two B
RACKET
B
and w
on the inside of the R
OLT
ASHER
one B
and w
OLT
ASHER
U
. Leave the B
PRIGHT
Note: Be sure the pre-installed washer is on the outside
of the R
U
IGHT
PRIGHT
4
(A) securing the F
RONT
G
and set it aside.
RONT
RILL
(D) securing the M
OTOR
C
and set it aside.
OTOR
OvER
(1). Lay the L
U
EFT
PRIGHT
H
(G) leading from the L
ARNESS
(F). Feed the M
RACKET
AIN
U
(1). Carefully tilt the L
EFT
PRIGHT
U
M
B
PRIGHT
OUNTING
RACKET
(H) directed forward, slide the
LATE
U
M
EFT
PRIGHT
OUNTING
and w
until it rests on
OLT
ASHER
U
to the L
EFT
PRIGHT
and w
OLTS
ASHERS
on the inside of the L
ASHER
and w
on the front side of the
ASHER
loose at this time.
OLTS
W
ain
ire
U
(1) or when
eft
priGHt
over the L
U
eft
priGHt
(2). with the R
IGHT
U
IGHT
PRIGHT
M
B
(K) and pre-
OUNTING
RACKET
until it rests on the f
ASHER
to the R
U
IGHT
PRIGHT
and w
(20 & 24). Use one
OLTS
ASHERS
U
IGHT
on the front side of the R
loose at this time.
OLTS
(2) when sliding it down to rest on the f
IMPORTANT
!
IMPORTANT
!
G
(B)
RILL
C
(E).
OvER
across
U
EFT
PRIGHT
EFT
w
IRE
EFT
EFT
. with the
U
EFT
PRIGHT
(20 & 24).
EFT
H
(G)
arness
M
oUntinG
T
M
OP
OUNTING
down
(C).
raMe
M
OUNTING
and
PRIGHT
IGHT
(c).
raMe
Advertisement
