Page of 68

Heat & Glo SLR (Cosmo) Owner's Manual

Hearth & home technologies gas fireplace owner's manual installation and operation manual.
Also See for SLR (Cosmo):
Brochure - 2 pages
Model:
SLR (Cosmo)
• Important operating
a n d m a i n t e n a n c e
instructions included.
WARNING: If the information in these
instructions is not followed exactly, a fi re
or explosion may result causing property
damage, personal injury, or death.
• DO NOT store or use gasoline or other fl am-
mable vapors and liquids in the vicinity of this
or any other appliance.
• What to do if you smell gas
- DO NOT try to light any appliance.
- DO NOT touch any electrical switch. DO
NOT use any phone in your building.
- Immediately call your gas supplier from a
neighbor's phone. Follow the gas suppli-
er's instructions.
- If you cannot reach your gas supplier, call
the fi re department.
• Installation and service must be performed
by a qualifi ed installer, service agency, or the
gas supplier.
This appliance may be installed as an OEM installation in
manufactured home (USA only) or mobile home and must be
installed in accordance with the manufacturer's instructions
and the manufactured home construction and safety standard,
Title 24 CFR, Part 3280 or Standard for Installation in Mobile
Homes, CAN/CSA Z240MH, in Canada.
This appliance is only for use with the type(s) of gas indicated
on the rating plate.
NOTICE
DO NOT DISCARD THIS MANUAL
• Read, understand and follow
these instructions for safe
installation and operation.
Heat & Glo • SLR • 2143-900 Rev. D • 12/08
Owner's Manual
• Leave this manual with
party responsible for use
and operation.
WARNING
HOT SURFACES!
Glass and other surfaces are hot during
operation AND cool down.
Hot glass will cause burns.
• DO NOT touch glass until it is cooled
• NEVER allow children to touch glass
• Keep children away
• CAREFULLY SUPERVISE children in same room as
fi replace.
• Alert children and adults to hazards of high temperatures.
High temperatures may ignite clothing or other fl ammable
materials.
• Keep clothing, furniture, draperies and other fl ammable
materials away.
This appliance has been supplied with an integral barrier
to prevent direct contact with the fi xed glass panel. DO
NOT operate the appliance with the barrier removed.
Contact your dealer or Hearth & Home Technologies if the
barrier is not present or help is needed to properly install one.
In the Commonwealth of Massachusetts installation must be
performed by a licensed plumber or gas fi tter.
See Table of Contents for location of additional Commonwealth
of Massachusetts requirements.
Installation and service of this appliance should be
performed by qualifi ed personnel. Hearth & Home
Technologies suggests NFI certifi ed or factory trained
professionals, or technicians supervised by an NFI
certifi ed professional.
Installation and Operation
1

   Also See for Heat & Glo SLR (Cosmo)

   Related Manuals for Heat & Glo SLR (Cosmo)

   Summary of Contents for Heat & Glo SLR (Cosmo)

  • Page 1

    Model: SLR (Cosmo) • Important operating a n d m a i n t e n a n c e instructions included. WARNING: If the information in these instructions is not followed exactly, a fi re or explosion may result causing property damage, personal injury, or death.

  • Page 2: A. Congratulations

    Read this manual before installing or operating this appliance. Please retain this owner’s manual for future reference. A. Congratulations Congratulations on selecting a Heat & Glo gas fi replace, an elegant and clean alternative to wood burning fi replaces. The Heat & Glo gas fi replace you have selected is designed to provide the utmost in safety, reliability, and effi...

  • Page 3: Table Of Contents

    Safety Alert Key: • DANGER! Indicates a hazardous situation which, if not avoided will result in death or serious injury. • WARNING! Indicates a hazardous situation which, if not avoided could result in death or serious injury. • CAUTION! Indicates a hazardous situation which, if not avoided, could result in minor or moderate injury. •...

  • Page 4: Table Of Contents

    13 Finishing A. Framing and Finishing Instructions ....48 B. Mantel and Wall Projections ..... . . 51 C.

  • Page 5: B. Limited Lifetime Warranty

    B. Limited Lifetime Warranty Hearth & Home Technologies LIMITED WARRANTY Hearth & Home Technologies (“HHT”) and its respective brands extends the following warranty for HHT gas, wood, pellet and electric appliances purchased from an authorized HHT dealer and installed in the United States of America or Canada. Warranty starts with date of purchase by the original owner (End User) except as noted for replacement parts.

  • Page 6

    B. Limited Lifetime Warranty (continued) • This limited warranty does not extend to or include surface fi nish on the appliance or terminations, door gasketing, glass gasketing, glass discoloration, fi rebrick, pellet logs, kaowool or other ceramic insulating materials. Rust and/or corrosion on any of the metal surfaces, cast iron components, baffl...

  • Page 7: A. Appliance Certifi Cation, B. Tempered Glass Specifi Cations, C. Btu Specifi Cations

    Listing and Code Approvals A. Appliance Certifi cation MODEL: SLR LABORATORY: Underwriters Laboratories, Inc. (UL) TYPE: Vented Gas Fireplace Heater STANDARD: ANSI Z21.88a-2007 CSA 2.33a-2007 Vented Gas Fireplace Heaters This product is listed to ANSI standards for “Vented Gas Fireplace Heaters” and applicable sections of “Gas Burn- ing Heating Appliances for Manufactured Homes and Recreational Vehicles”, and “Gas Fired Appliances for Use at High Altitudes”.

  • Page 8: H. Requirements For The Commonwealth Of Massachusetts

    Note: The following requirements reference various Massachusetts and national codes not contained in this document. H. Requirements for the Commonwealth of Massachusetts For all side wall horizontally vented gas fueled equipment installed in every dwelling, building or structure used in whole or in part for residential purposes, including those owned or operated by the Commonwealth and where the side wall exhaust vent termination is less than seven (7)

  • Page 9: A. Gas Fireplace Safety, B. Your Fireplace

    Operating Instructions A. Gas Fireplace Safety WARNING HOT SURFACES! Glass and other surfaces are hot during operation AND cool down. Hot glass will cause burns. • DO NOT touch glass until it is cooled • NEVER allow children to touch glass •...

  • Page 10: C. Clear Space, D. Decorative Doors And Fronts, E. Fixed Glass Assembly

    C. Clear Space WARNING! DO NOT place combustible objects in front of the fi replace or block louvers. High temperatures may start a fi re. See Figure 2.2. Avoid placing candles and other heat-sensitive objects on mantel or hearth. Heat may damage these objects. Figure 2.2 Clear Space D.

  • Page 11: H. Lighting Instructions (ipi)

    H. Lighting Instructions (IPI) The IPI system may be operated with two D-cell batteries. When using batteries, unplug the transformer. To prolong battery life, remove them when using the transformer. FOR YOUR SAFETY READ BEFORE LIGHTING WARNING: If you do not follow these instructions exactly, a fi re or explosion may result causing property damage, personal injury or loss of life.

  • Page 12: I. After Fireplace Is Lit, J. Frequently Asked Questions

    I. After Fireplace is Lit Initial Break-in Procedure • The fireplace should be run three to four hours continuously on high. • Turn the fi replace off and allow it to completely cool. • Remove fi xed glass assembly. See Section 14.F. •...

  • Page 13: A. Maintenance Tasks-homeowner

    Maintenance and Service Any safety screen or guard removed for servicing must be replaced prior to operating the fi replace. When properly maintained, your fi replace will give you many years of trouble-free service. We recommend an- nual service by a qualifi ed service technician. A.

  • Page 14: B. Maintenance Tasks-qualifi Ed Service Technician

    Venting Frequency: Seasonally By: Homeowner Tools needed: Protective gloves and safety glasses. • Inspect venting and termination cap for blockage or obstruction such plants, bird nests, leaves, snow, debris, etc. • Verify termination cap clearance to subsequent construc- tion (building additions, decks, fences, or sheds). See Section 6.

  • Page 15: A. Typical Appliance System

    Getting Started A. Typical Appliance System NOTICE: Illustrations and photos refl ect typical installations and are for design purposes only. Illustrations/diagrams are not drawn to scale. Actual product may vary from pictures in manual VERTICAL TERMINATION CAP NON-COMBUSTIBLE ROOF FLASHING MAINTAINS MINIMUM CLEARANCE AROUND PIPE (SECTION 10)

  • Page 16: B. Design And Installation Considerations, C. Tools And Supplies Needed, D. Inspect Appliance And Components

    B. Design and Installation Considerations Heat & Glo direct vent gas appliances are designed to operate with all combustion air siphoned from outside of the building and all exhaust gases expelled to the outside. No additional outside air source is required. Installation MUST comply with local, regional, state and national codes and regulations.

  • Page 17: A. Selecting Appliance Location

    Framing and Clearances A. Selecting Appliance Location When selecting a location for the appliance it is important to consider the required clearances to walls (see Figure 5.1). WARNING! Risk of Fire or Burns! Provide adequate clearance around air openings and for service access. Due to high temperatures, the appliance should be locat- ed out of traffi...

  • Page 18: B. Constructing The Appliance Chase, C. Clearances

    B. Constructing the Appliance Chase A chase is a vertical box-like structure built to enclose the gas appliance and/or its vent system. In cooler climates the vent should enclosed inside the chase. NOTICE: Treatment of ceiling fi restops and wall shield fi...

  • Page 19: D. Mantel And Wall Projections

    D. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as specifi ed. Framing or fi nishing material closer than the minimums listed must be construct- ed entirely of noncombustible materials (i.e., steel studs, concrete board, etc).

  • Page 20

    3-1/2 in. 1 in. 1-9/16 in. AIR SPACE Figure 5.8 Non-Combustible Zone 1/2 in. SHEETROCK NON-COMBUSTIBLE BOARD SHIPPED WITH APPLIANCE Heat & Glo • SLR • 2143-900 Rev. D • 12/08...

  • Page 21: A. Vent Termination Minimum Clearances

    Termination Locations A. Vent Termination Minimum Clearances WARNING Fire Risk. Maintain vent clearance to combustibles as specifi ed. • DO NOT pack air space with insulation or other materials. Failure to keep insulation or other materials away from vent pipe may cause overheating and fi re. 2 FT.

  • Page 22

    = VENT TERMINAL = 12 inches...clearances above grade, veranda, (See Note 1) porch, deck or balcony = 12 inches...clearances to window or door that may be opened, or to perma- nently closed window. (Glass) = 18 inches...vertical clearance to unventilated soffi...

  • Page 23: A. Approved Pipe, B. Vent Table Key, C. Use Of Elbows, D. Measuring Standards

    Vent Information and Diagrams A. Approved Pipe This appliance is approved for use with Hearth & Home Technologies SLP venting systems. Refer to Section 16B for vent component information. DO NOT mix pipe, fi ttings or joining methods from differ- ent manufacturers.

  • Page 24

    Fire Risk. Explosion Risk. Do NOT pack insulation or other combustibles between ceiling fi restops. • ALWAYS maintain specifi ed clearances around venting and fi restop systems. • Install wall shield and ceiling fi restops as specifi ed. Failure to keep insulation or other material away from vent pipe may cause fi re. Top Vent - Horizontal Termination Venting with 1 elbow Maximum...

  • Page 25

    1. Top Vent - Horizontal Termination - (continued) V Minimum 90° Elbow 1 ft. 1 ft. 305 mm 2 ft. 2 ft. 610 mm 4 ft. 3 ft. 914 mm 6 ft. 4 ft. 1.2 m 14 ft. H + H MAX.

  • Page 26

    1. Top Vent - Horizontal Termination - (continued) Minimum Maximum 90° Elbow 6 ft. 1 ft. 305 mm 10 ft. 2 ft. 610 mm 12 ft. 3 ft. 914 mm 14 ft. *No specifi c restrictions on this value EXCEPT V Figure 7.6 Top Vent - Horizontal Termination Venting with 3 elbows...

  • Page 27

    1. Top Vent - Horizontal Termination - (continued) V Minimum 90° Elbow 3 ft. 914 mm 15 ft. MAX. =15 ft. (4.6 m) Figure 7.7 Top Vent - Horizontal Termination Venting with 3 elbows MAXIMUM Note: Use SLP Series components only. SLR (NG ONLY) 4.6 m Note: There MUST be a 25%...

  • Page 28

    Top Vent - Vertical Termination No Elbows = 44 ft. Max. (13.4 m) Note: If installing a vertical vent/termination off the top of the appliance, the optional exhaust restrictor may be needed. Note: Use SLP Series components only. Figure 7.8 Vertical Vent Maximum Exhaust restrictors are recommended for these vertically terminated products which have excessive draft.

  • Page 29

    Minimum 90° Elbow 1 ft, 152 mm 2 ft. 457 mm 3 ft. 914 mm 4 ft. 1.1 m * No specifi c restrictions on this value EXCEPT V Figure 7.11 Top Vent - Vertical Termination Venting with 2 elbows H Maximum 2 ft.

  • Page 30

    Minimum 90° Elbow 1 ft. 2 ft. 3 ft. 4 ft. * No specifi c restrictions on this value EXCEPT V Figure 7.12 Top Vent - Vertical Termination Venting with 3 elbows Maximum 1 ft. 305 mm 305 mm 2 ft. 610 mm 610 mm 4 ft.

  • Page 31

    Top Vent - Vertical Termination Venting with 4 elbows Note: Use SLP Series components only. Note: There MUST be a 25% reduction in total H when using fl ex vent except when using the simple up and out installation (see Figure 5.3). Figure 7.13 MIN.

  • Page 32: A. Pipe Clearances To Combustibles, B. Wall Penetration Framing

    Vent Clearances and Framing A. Pipe Clearances to Combustibles WARNING! Risk of Fire! Maintain air space clearance to vent. DO NOT pack insulation or other combustibles: • Between ceiling fi restops • Between wall shield fi restops • Around vent system Failure to keep insulation or other material away from vent pipe may cause over heating and fi...

  • Page 33: C. Install The Ceiling Firestop

    C. Install the Ceiling Firestop A ceiling fi restop MUST be used between fl oors and attics. • SLP pipe only - Frame opening 9 in. x 9 in. (229 mm x 229 mm) whenever the vent penetrates a ceiling/floor (see Figure 8.4).

  • Page 34: D. Install Attic Insulation Shield

    D. Install Attic Insulation Shield WARNING! Fire Risk. DO NOT allow loose materials or insulation to touch vent. Hearth & Home Technologies Inc. requires the use of an attic shield. The National Fuel Gas Code ANSI Z223.1 and NFPA 54 requires an attic shield constructed of 26 gauge minimum metal that extends at least 2 in.

  • Page 35

    Appliance Preparation A. Top Vent CAUTION! Risk of Cuts, Abrasions or Flying Debris. Wear protective gloves and safety glasses during instal- lation. Sheet metal edges are sharp. ELBOW HEAT SHIELD SHOWN IN SHIPPING POSITION Figure 9.1 Elbow Shield Shown as Shipped If venting with a 90 degree elbow directly off of the top of the appliance, the elbow heatshield must be repositioned as shown in Figure 9.2.

  • Page 36: B. Securing And Leveling The Appliance

    B. Securing and Leveling the Appliance WARNING! Risk of Fire! Prevent contact with: • Sagging or loose insulation • Insulation backing or plastic • Framing and other combustible materials Block openings into the chase to prevent entry of blown- in insulation. Make sure insulation and other materials are secured.

  • Page 37: A. Assemble Vent Sections

    Installing Vent Pipe (SLP Pipe) A. Assemble Vent Sections To attach the fi rst vent component to the starting collars of the appliance: • Lock the vent components into place by sliding the pipe section onto the collar. • Align the seam of the pipe and seam of collar to allow engagement.

  • Page 38: B. Assemble Slip Sections, C. Secure The Vent Sections

    B. Assemble Slip Sections • Slide the inner fl ue of the slip section into the inner fl ue of the pipe section and the outer fl ue of the slip section over the outer fl ue of the pipe section. See Figure 10.3. •...

  • Page 39: D. Disassemble Vent Sections, E. Install Decorative Ceiling Components

    D. Disassemble Vent Sections • Rotate either section (see Figure 8.7) so the seams on both pipe sections are aligned as shown in Figure 10.8. • Pull carefully to separate the pieces of pipe. Figure 10.7 Rotate Seams for Disassembly Figure 10.8 Align and Disassemble Vent Sections E.

  • Page 40: F. Install Metal Roof Flashing, G. Assemble And Install Storm Collar

    F. Install Metal Roof Flashing Note: Skip this section if using the RF4-8. • See minimum vent heights for various pitched roofs (Figure 10.11) to determine the length of pipe to extend through the roof. • Slide the roof fl ashing over the pipe sections extending through the roof as shown in Figure 10.12.

  • Page 41: H. Install Rf4-8

    H. Install RF4-8 The RF4-8 may be used in place of the roof fl ashing and storm collar (Sections 10.F and Section 10.G.) Pipe must be supported within 12 inches of the roofl ine using plumbers strapping or an SLP-FS when using the RF4-8 Flashing.

  • Page 42: I. Install Vertical Termination Cap, J. Install Decorative Wall Components

    I. Install Vertical Termination Cap • Attach the vertical termination cap by sliding the inner collar of the cap into the inner fl ue of the pipe section while placing the outer collar of the cap over the outer fl ue of the pipe section. •...

  • Page 43: L. Install Horizontal Termination Cap

    L. Install Horizontal Termination Cap WARNING! Risk of Fire! The telescoping fl ue section of the termination cap MUST be used when connecting vent. • 1-1/2 (38 mm) minimum overlap of fl ue telescoping section is required. Failure to maintain overlap may cause overheating and fi...

  • Page 44: A. Fuel Conversion, B. Gas Pressure

    11 11 Gas Information A. Fuel Conversion • Make sure the appliance is compatible with available gas types. • Conversions must be made by a qualified service technician using Hearth & Home Technologies specifi ed and approved parts. B. Gas Pressure •...

  • Page 45: C. Gas Connection, D. High Altitude Installations

    Figure 11.3 Gas Fitting Access Figure 11.4 Gas Fitting and Junction Box Access C. Gas Connection • Refer to Reference Section 16 for location of gas line access in appliance. • Gas line may be run through knockout(s) provided. • The gap between supply piping and gas access hole may be caulked with high temperature caulk or stuffed with non-combustible, unfaced insulation to prevent cold air infi...

  • Page 46: A. Wiring Requirements, B. Intellifi Re Ignition System Wiring, C. Optional Accessories Requirements

    Electrical Information A. Wiring Requirements NOTICE: This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with National Electric Code ANSI/NFPA 70-latest edition or the Canadian Electric Code CSA C22.1. •...

  • Page 47: D. Electrical Service And Repair, E. Junction Box Installation

    TRANSFORMER PLUG IN BATTERY PACK Figure 12.2 Intellifi re Pilot Ignition (IPI) Wiring Diagram with Wall Switch or Thermostat D. Electrical Service and Repair WARNING! Risk of Shock! Label all wires prior to dis- connection when servicing controls. Wiring errors can cause improper and dangerous operation.

  • Page 48: A. Framing And Finishing Instructions

    Finishing A. Framing and Finishing Instructions WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as specifi ed. Framing closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause fi...

  • Page 49

    WARNING! Risk of Fire! Maintain specifi ed air space clearances to combustibles. Failure to comply with these instructions may cause a fi re or cause the appliance to overheat. Ensure that the one inch back clearance and one inch side clearances are maintained. TOP FLANGE NON-COMBUSTIBLE BOARD (PROVIDED WITH UNIT)

  • Page 50

    16 IN. Figure 13.6 Confi rm Fireplace Opening Dimension SIDE WALL SHEATHING 1/2 INCH CUT IN WALL SHEATHING LOWER WALL SHEATHING Figure 13.7 Lower Drywall Detail Sealing Joints The joints between the drywall sides and drywall above the top factory installed non-combustible board CAN NOT be sealed with a combustible drywall tape.

  • Page 51: B. Mantel And Wall Projections

    B. Mantel and Wall Projections WARNING! Risk of Fire! Comply with all minimum clear- ances to combustibles as specifi ed. Framing closer than the minimums listed must be constructed entirely of noncom- bustible materials (i.e., steel studs, concrete board, etc.) Failure to comply could cause fi...

  • Page 52: C. Facing Material

    C. Facing Material • Facing and/or fi nishing materials must not interfere with air fl ow through louvers, operation of louvers or doors, or access for service. • Facing and/or fi nishing materials must never overhang into the glass opening. •...

  • Page 53

    Non-Combustible Finish Materials 0 Inches to 4 Inches Thick Inside Fit Method Note: The Inside Fit application is only approved for the Tonic decorative front. The Tonic decorative front is approved for inside fi t ap- plications. Non-combustible fi nishing materials up to 4 inches thick can be installed around the Tonic front (left, right, top, and bottom).

  • Page 54: D. Decorative Fronts

    D. Decorative Fronts WARNING! Risk of Fire! A decorative front is required for this model. DO NOT operate this appliance without a decorative front in place. Only doors certifi ed for use with this appliance model may be used. Contact your dealer for a list of doors that may be used.

  • Page 55: A. Remove Fixed Glass Assembly, B. Remove The Shipping Materials, C. Clean The Appliance

    Appliance Setup A. Remove Fixed Glass Assembly See Section 14F. B. Remove the Shipping Materials Remove shipping materials from inside or underneath the fi rebox. The standard black rock media and manual bag assembly are also shipped underneath the fi rebox. C.

  • Page 56: E. Rock Media Instructions

    E. Rock Media Instructions CAUTION Sharp Edges • Wear protective gloves and safety glasses during installation. Cleaning the Rock During shipment of the Rock Media, dust and debris can accumulate. It is recommended that the Rock Media be rinsed thoroughly with water to remove dust and small glass particles.

  • Page 57

    4. The rock media placement jig must remain in place while media is placed on the basepan and around the pilot bracket. 5. Remove the rock media placement jig by removing the screw as noted in Figure 14.5. Figure 14.5. Remove Screw 6.

  • Page 58: F. Fixed Glass Assembly, G. Install The Mesh, H. Air Shutter Setting

    F. Fixed Glass Assembly WARNING! Risk of Asphyxiation! Handle fi xed glass assembly with care. Inspect the gasket to ensure it is undamaged and inspect the glass for cracks, chips or scratches. • DO NOT strike, slam or scratch glass. •...

  • Page 59: A. Intellifi Re Ignition System

    Troubleshooting With proper installation, operation, and maintenance your gas appliance will provide years of trouble-free service. If you do experience a problem, this troubleshooting guide will assist a qualifi ed service technician in the diagnosis of a problem and the corrective action to be taken. This troubleshooting guide can only be used by a qualifi ed service technician. Contact your dealer to arrange a service call by a qualifi...

  • Page 60

    Intellifi re Ignition System - (continued) Symptom a. A shorted or loose connection in fl ame 4. Pilot lights but contin- sensing rod. ues to spark, and main burner will not ignite. (If the pilot continues to spark after the b.

  • Page 61: A. Appliance Dimension Diagram

    Reference Materials A. Appliance Dimension Diagram Dimensions are actual appliance dimensions. Use for reference only. For framing dimensions and clearances refer to Section 5. GAS LINE ACCESS ELECTRICAL ACCESS LEFT VIEW Location Figure 16.1 Appliance Dimensions 1 INCH STANDOFF Ø NON-COMBUSTIBLE ZONE (PROVIDED WITH UNIT) FRONT VIEW...

  • Page 62: B. Vent Components Diagrams

    B. Vent Components Diagrams 13-7/8 in. 9-1/2 in. (352 mm) (241 mm) 11-5/8 in. (295 mm) 14 in. 12-1/8 in. 7-1/8 in. (308 mm) (356 mm) (181 mm) DRC-RADIUS 5-3/4 in. Cap Shield (146 mm) COOL-ADD Cap Shield 11-7/8 in. 5 in.

  • Page 63

    B. Vent Components Diagrams (continued) 6-1/2 in. 165 mm 8-3/4 in. 222 mm 6-5/8 in. 168 mm SLP-45 - 45° Elbow Effective Height/ Length SLP-PIPE SLP-HVS Horizontal Pipe Support Figure 16.5 SLP Series Vent Components 6 in. 152 mm Effective Height/Length Pipe inches SLP4...

  • Page 64

    B. Vent Components Diagrams (continued) SLK-SNKD Snorkel Termination Cap SLP-TRAP2 Horizontal Ceiling Firestop Termination Cap 8-1/8 in. (206 mm) 15 in. (381 mm) Figure 16.6 SLP Series Vent Components SLP-CCS-BK Cathedral Ceiling Termination Cap Support Box-Black SLP-WT-BK SLP-DCF-BK Wall Thimble-Black Black 13 in.

  • Page 65

    C. Service Parts Beginning Manufacturing Date: July 2008 Service Parts Diagram Ending Manufacturing Date: ______ Part number list on following page. Heat & Glo • SLR • 2143-900 Rev. D • 12/08...

  • Page 66: C. Service Parts List

    C. Service Parts List IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. ITEM DESCRIPTION Elbow Heat Shield Sheet Rock Ledge Top Panel, Finishing Edge...

  • Page 67

    Service Parts Valve Assembly Diagram/ Parts List IPI Valve Assembly IMPORTANT: THIS IS DATED INFORMATION. When requesting service or replacement parts for your appliance please provide model number and serial number. All parts listed in this manual may be ordered from an authorized dealer. ITEM DESCRIPTION Pilot Bracket Kit...

  • Page 68: D. Contact Information

    D. Contact Information Please contact your Heat & Glo dealer with any questions or concerns. ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ ________________________________________________________________________________ • Important operating a n d m a i n t e n a n c e instructions included.

Comments to this Manuals

Symbols: 0
Latest comments: