Appendix A (Alternate Floor Protection) - Jøtul F 500 Installation And Operating Instructions Manual

USA/CANADA
Pos. No. Pos. No. Pos. No. Pos. No. Description Pos. No. Description Description Description Description
1 Leg
2 Latch (Side Door)
3 Ash House Complete
4 Ash Door
5 Smoke Outlet
6 Fire Grate
7 Air Valve
8 Bottom
9 Inner Bottom
10 Rear Plate
11 Tube Frame Holder
12 Air Manifold
13 Front
14 Inner Front
15 Side Right
16 Side Left
17 Front Door
18 Ash Lip
19 Top
20 Tube Holder Upper Right
21 Tube Holder Upper Left
22 Tube Holder Bottom Right
23 Tube Holder Bottom Left
24 Inspection Cover
25 Side Door
26 Burnplate Side/Door
27 Baffle Plate
2 8 Top Cover
29 Nut
30 Screw Hexagon Stainless
31 Screw Hexagon
32 Screw Collar Hexagon
33 Screw Hexagon
34 Screw Hexagon Stainless
35 Screw Panh.
36 Washer Blackchromating
37 Washer ELZN
3 8 Screw Cylinder Head
39 Screw Cylinder Head
40 Spring Pin
41 Screw Panh.
42 Screw Hexagon Stainless
43 Screw Allen
44 Screw Collar Hexagon
45 Washer
46 Washer Insul.
47 Gasket (Side Door)
48 Latch Ash Door
49 Gasket (Front Door)
50 Spring
51 Latch Bolt Side Door
52 Sleeve
53 Wooden Knob + Small Parts
54 Hinge Pin Front/Side Door
56 Wooden Knob Ash Door
57 Ash Pan
5 8 Handler for Air Vent
59 Nut M10
60 Handle Ash Door Complete
61 Clip
62 Hinge Pin, Ash Door
63 Gasket (Ash Door)
64 Gasket (Ash House)
65 Gasket (Top)
66 Insulation Blanket
67 Gasket (Smoke Outlet)
68 Glass
69 Catch
70 Refractory Brick
71 Insulation Blanket Top
72 Tube Rear
73 Tube, Middle and Front
75 Heat Shield Bottom
7 7 Heat Shield Rear + Top Exit
7 8 Latch Bolt Front Door
79 Glass Clip
80 Gasket (Door Glass)
81 Gasket (Top Cover)
8 2 Latch (Front Door)
8 3 Washer
84 Air Chamber Complete
8 5 Adapter Outside Air
Only use replacements parts provided through your Authorized Jøtul dealer.
18
Alternate Floor Protection
All floor protection materials must be non-combustible ie.
metal, brick, stone, mineral fiber boards). Any combustible
material may not be used.
The easiest means of determining if a proposed alternate floor
material meets requirements listed in this manual is to follow
this procedure.
R-value = thermal resistance
k-value = thermal conductivity
C-value = thermal conductance
1. Convert the specification to R-value;
a. If R-value is given, no conversion is needed.
b. If k-value is given with a required thickness (T) in inches:
R=1/k X T.
c. If C-value is given: R=1/C.
2. Determine the R-value of the proposed alternate floor
protector.
a. Use the formula in Step 1 to convert values not
expressed as "R".
b. For multiple layers, add R-values of each layer to
determine overall R-value.
3. If the overall R-value of the system is greater than the R-
value of the specified floor protector, the alternate is
acceptable.
Example:
The specified floor protector should be 3/4" thick material with
a k-factor of 0.84. The proposed alternate is 4" brick with a C-
factor of 1.25 over 1/8" mineral board with a k-factor of 0.29.
Step A. Use formula above to convert specifications
to R-value. R=1/k X T= 1/.84 X .75 = .893
Step B. Calculate R of proposed system.
4" brick of C-1.25, therefore
R brick = 1/C = 1/1.25 = 0.80.
1/8" mineral board of k = 0.29 therefore
R mineral board = 1/.29 X 0.125 = 0.431
Total R = R brick + R mineral board=
0.8 + 0.431=1.231
Step C. Compare proposed system R = 1.231 to specified R of
0.893. Since R is greater than required, the system is acceptable.
Definitions:
Thermal conductance =
C = Btu =
(hr)(ft 2 )(F)
Thermal conductivity =
k = Btu =
(hr)(ft 2 )(F)
Thermal resistance =
R = Btu =
(hr)(ft 2 )(F)
For the Jøtul F 600 woodstove requires floor protection with
a minimum insulating r value of 0.5.
Alcoves require an r value of 1.6.
W
(m 2 )(K)
W = (Btu)
(m 2 )(K) (hr)(ft)(F)
2
(m )(K) = (Btu)(inch)
W (hr)(ft 2 )(F)