Chorus; Flanger - Roland RD-800 Manual

18: CHORUS

This is a stereo chorus. A filter is provided so that you can adjust the
timbre of the chorus sound.
Balance D
L in
Chorus
Chorus
R in
Balance D
Parameter Value
Switch
OFF, ON
Depth Knob
RATE,
BALANCE
Rate Knob
OFF,
Filter Type LPF,
HPF
Cutoff Freq 200–8000 [Hz]
Pre Delay 0.0–100 [msec]
Rate (sync sw) #
OFF, ON
0.05–10.00 [Hz]
Rate (Hz) #/
Rate (note) #
note (p. 31)
Depth 0–127
Phase 0–180 [deg]
Low Gain -15–+15 [dB]
High Gain -15–+15 [dB]
D100:0W–
Balance #
D0:100W
Level 0–127
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Turns the effect on/off.
Specifies the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Specifies the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above
the Cutoff Freq
HPF: cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from the direct
sound until the chorus sound is heard.
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner's manual p. 24).
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the chorus sound (W)
Output Level

19: FLANGER

This is a stereo flanger. (The LFO has the same phase for left and
right.) It produces a metallic resonance that rises and falls like a jet
airplane taking off or landing. A filter is provided so that you can
adjust the timbre of the flanged sound.
Balance D
L in
Flanger
Feedback
Feedback
Flanger
R in
Balance D
Parameter Value
Switch
OFF, ON
Depth Knob
RATE,
FEEDBACK,
BALANCE
Rate Knob
OFF,
Filter Type
LPF,
HPF
Cutoff Freq 200–8000 [Hz]
Pre Delay 0.0–100 [msec]
Rate (sync sw) # OFF, ON
0.05–10.00 [Hz]
Rate (Hz) #/
Rate (note) #
note (p. 31)
Depth
0–127
Phase 0–180 [deg]
Feedback # -98–+98 [%]
Low Gain -15–+15 [dB]
High Gain -15–+15 [dB]
D100:0W–
Balance #
D0:100W
Level
0–127
Modulation FX Parameters
2-Band
L out
EQ
Balance W
Balance W
2-Band
R out
EQ
Explanation
Turns the effect on/off.
Specifies the parameter that is
controlled by the MODULATION FX
[DEPTH] knob.
Specifies the parameter that is
controlled by the MODULATION FX
[RATE] knob.
Type of filter
OFF: no filter is used
LPF: cuts the frequency range above
the Cutoff Freq
HPF: cuts the frequency range below
the Cutoff Freq
Basic frequency of the filter
Adjusts the delay time from the direct
sound until the flanger sound is heard.
If this is ON, the modulation is
synchronized to the tempo of the
rhythm (owner's manual p. 24).
Frequency of modulation
Depth of modulation
Spatial spread of the sound
Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative "-" settings will invert the
phase.
Gain of the low range
Gain of the high range
Volume balance between the direct
sound (D) and the flanger sound (W)
Output Level
13