Advertisement
Quick Links
031
OPERATION MANUAL
COUNTERTOP
WARMER
Model: SHW-11
MODELS
SHW-4
SHW-7
SHW-11
SHW-1220
Includes
INSTALLATION
USE & CARE
Model: SHW-1220
IMPORTANT: DO NOT DISCARD THIS MANUAL
This manual is considered to be part of the appliance and is to be given to the OWNER or
MANAGER of the restaurant, or to the person responsible for TRAINING OPERATORS of
this appliance. Additional manuals are available from your WELLS DEALER.
THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR
INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any
questions concerning installation, operation or maintenance of this equipment.
PRINTED IN CHINA
306484
05
p/n
Rev.A ECN-12928
M031
0912 cps
Advertisement
Related Manuals for Wells Showroom SHW-4
Summary of Contents for Wells Showroom SHW-4
- Page 1 Additional manuals are available from your WELLS DEALER. THIS MANUAL MUST BE READ AND UNDERSTOOD BY ALL PERSONS USING OR INSTALLING THIS APPLIANCE. Contact your WELLS DEALER if you have any questions concerning installation, operation or maintenance of this equipment.
- Page 2 Wells Mfg. Co. Portable models (a device with a THIS WARRANTY IS THE COMPLETE AND ONLY cord and plug) must be taken or shipped to Wells Mfg. Co., WARRANTY, EXPRESSED OR IMPLIED IN LAW OR IN transportation charges prepaid, for service. In addition to...
- Page 3 PARTS & SERVICE CUSTOMER SERVICE DATA INTRODUCTION Thank You for purchasing this Wells Manufacturing Co. appliance. Proper installation, professional operation and consistent maintenance of this appliance will ensure that it gives you the very best performance and a long, economical service life.
- Page 4 FEATURES & OPERATING CONTROLS THERMOSTAT 1. Warmers are equipped with a thermostat. Power is applied to the heating element according to the control knob position and the actual temperature at the sensing element. 2. The desired temperature is controlled by rotating the TEMPERATURE CONTROL KNOB.
-
Page 5: Agency Listing Information
Exposed surfaces of this appliance can be hot to the touch and may cause burns. CAUTION: Do not operate this appliance if it is damaged. Call Wells Service Hot Surface Department (888) 492-2782 for service or repairs. Exposed surfaces can be hot This manual is considered to be a permanent part of the appliance. - Page 6 INSTALLATION NOTE: DO NOT discard UNPACKING & INSPECTION the carton or other packing Carefully remove the appliance from the carton. Remove all materials until you have protective plastic film, packing materials and accessories from the inspected the appliance for Appliance before connecting electrical power or otherwise performing hidden damage and tested it any installation procedure.
- Page 7 CAUTION: Hot Surface 1. Carefully read the description of the warmer operation on the specification sheet. 2. a. Wells Manufacturing recommends operating WET for Exposed surfaces can be hot consistent food heating. to the touch and may cause b. If your wet-operation warmer is allowed to run dry, turn it burns.
-
Page 8: Cleaning Instructions
ELECTRIC SHOCK allow grease and water to leak into insulation and heating element, HAZARD causing a potential fire and/or electric shock hazard. Contact Wells Mfg. Co. (888) 492-2782 to inspect warmer if water or grease DO NOT submerge warmer contamination is suspected. - Page 9 15 minutes and consult a physician TOOLS: Wells Delime Cleaner (1 package per pan) Plastic Scouring Pad SKIN: Wash with soap and Clean Cloth or Sponge water INHALATION: Relocate to 1.
- Page 10 Internal damage Contact Wells Service Dept. (888) 492-2782 for repairs Warmer slow to heat Mineral deposits on pan acting as Clean pan(s) with Wells Delime a insulator Cleaner. Connected to wrong voltage Verify supply voltage (must match voltage on warmer nameplate)
- Page 11 Never use metal implements, wire brushes, abrasive scratch pads or steel wool to clean stainless steel. Warmer pans, insets and other vessels are subject to a harsher environment. Wells Manufacturing uses a very high quality stainless steel for our food warmer pans. Even the...
- Page 12 ACCESSORIES DESCRIPTION PART NO. Always use an inset. DO NOT place food directly into the warmer pan. INSETS 2½ QT. ROUND INSET w/ slotted cover 20773 4 QT. ROUND INSET w/ slotted cover 20774 7 QT. ROUND INSET w/ slotted cover 20587 11 QT.
-
Page 13: Customer Service Data
PARTS & SERVICE DESCRIPTION PART NO. Wells Manufacturing Co. 2 Erik Circle P. O. Box 280 Verdi, NV 89439 CLEANERS phone: (888) 492-2782 DELIME CLEANER (Case of 24 7 oz. packets) 22838 fax: (888) 492-2783 (Service Parts Dept.) CUSTOMER SERVICE DATA... - Page 14 PRINTED IN CHINA...