Setting Water Hardness; Measuring Water Hardness; Set Water Hardness; Technical Specification - DeLonghi ESAM 04.320 Owner's Manual

1. accendere la macchina.
2. Press the MENU button to enter the settings menu. Press
the or button until "descale" is displayed;
3. Press the OK button. "descale Confirm?" is displayed. Press
OK to enable the function.
4. The message " Add descaler Press OK" is displayed.
5. Before confirming, empty the water tank (a13).
Pour the descaler diluted with water (respecting the
proportions indicated on the descaler pack) into the water
tank and replace the tank in the appliance.
6. Place an empty container with a minimum capacity of 1.5
litres under the hot water spout.
Important! Danger of burns
hot water containing acid flows out of the hot water spout.
avoid contact with splashes of water.
7. Confirm with the OK button.
8. "TURN STEAM KNOB" is displayed.
9. after turning the knob to the I position (fig. 4), "descale
Press OK" is displayed.
10. after confirming by pressing OK, the message "descale
underway" is displayed.
The descale programme starts and the descaler liquid
comes out of the water spout.
The descale programme automatically performs a series
of rinses and pauses to remove limescale deposits from
inside the machine.
After about 30 minutes, "TURN STEAM KNOB" is displayed.
When the steam knob is turned to the 0 position, "rinsing Fill
TANK" is displayed.
11. The appliance is now ready for rinsing through with
clean water. remove the water tank, empty, rinse under
running water, fill with clean water and replace. "TurN
STEAM KNOB" is displayed. When the steam knob is
turned to the I position, " Rinsing... Press OK" is displayed.
12. empty the container used to collect the descaler solution
and replace it under the hot water spout.
13. Press the OK button to start rinsing. hot water flows out
of the spout and the message "rinsing... Please wait" is
displayed.
14. When the water tank is completely empty, "TurN STeaM
KNOB" is displayed.
15. When the steam knob is turned to the 0 position, the
appliance goes off.
To use it again, turn the appliance on by pressing the
button.

SETTING WATER HARDNESS

The deSCale message is displayed after a period of time
established according to water hardness.
The machine is set by default for a hardness value of 4 (very
hard water).
The machine can also be programmed according to the actual
hardness of the mains water in the various regions, varying the
frequency with which the message is displayed.

Measuring water hardness

1. remove the "ToTal hardNeSS TeST" indicator paper from
its pack.
2. immerse the paper completely in a glass of water for one
second.
3. remove the paper from the water and shake lightly. after
about a minute, 1, 2, 3, or 4 red squares form, depending
on the hardness of the water. each square corresponds to
one level.
level 1 - soft water l
level 2 - slightly hard water
ll
level 3 - hard water
lll
level 4 - very hard water
llll

Set water hardness

1. Press the MENU button to enter the settings menu.
2. Press the or button and select "Water hardness".
3. Confirm the selection by pressing the OK button.
4. Press the or
identified using the indicator paper (see figure in the
previous section).
5. Press the OK button to confirm the setting.
6. Press the ESC button to exit the menu.
The machine is now reprogrammed with the new water
hardness setting.

TECHNICAl SPECIFICATION

voltage:
absorbed power:
Pressure:
Water tank capacity:
Size: lxhxd:
Cable length:
Weight:
Max. beans container capacity
16
button to set the water hardness
220-240 v~ 50/60 hz max. 10a
1350W
15 bar
282x374x441 mm
1,5 m
11,4 Kg
250 g
1,7 l