ABLE OF ONTENTS 1. Before You Begin .................................. 3 What is included ..................................3 Unpacking Instructions ................................3 Safety Instructions ..................................4 LED Expected Lifespan ................................4 2. Introduction ................................... 5 Features ...................................... 5 DMX Channel Summary ................................6 Product Overview ..................................7 3.
1. B EFORE EGIN What is included 1 x COLORdash™ Batten 1 x Power cable with plug 1 x 6ft (2m) power linking cable 1 x Warranty Card 1 x User Manual Unpacking Instructions Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that all parts are present, and have been received in good condition.
There are no user serviceable parts inside the unit. Do not open the housing or attempt any repairs yourself. In the unlikely event your unit may require service, please contact CHAUVET at: 954-929-1115. Caution! After prolonged periods of operation, the fixture chassis may reach high temperatures.
2. I NTRODUCTION Features 3, 4, 10, or 12-channel DMX-512 LED bank system (with ID addressing) Operating modes 3-channel: RGB control 4-channel: RGB, dimmer 10-channel: RGB, ID, dim, macro, strobe, automatic, custom, module select 12-channel: RGB of 4 separate sections RGB color mixing with or without DMX controller Built-in automated programs via master/slave or DMX Program and recall custom programs via master/slave or DMX...
DMX Channel Summary The COLORdash™ Batten has a total of 4 DMX channel configurations, referred to as “Personalities” in this manual and in the fixture onboard control board. The 4 personalities are [STAGE 1, BLOCK, ARC1, ARC1+D]. Each of the different personalities can be accessed from the control panel.
Product Overview Bracket Adjustment Power Link Out DMX Out Power Out Power In DMX In Control Panel Fuse holder Cooling Fan Bracket Adjustment knob COLORdash™ Batten User Manual 9/5/2008 9:49 AM...
3. SETUP AC Power This fixture has an auto-switching power supply that can accommodate a wide range of input voltages. The only thing necessary to do before powering on the unit is to make sure the line voltage you are applying is within the range of accepted voltages. This fixture will accommodate between 100V and 240V AC 50-60 Hz.
The fixture includes a mounting yoke to which a rigging clamp can be attached. You must supply your own clamp and make sure the clamp is capable of supporting the weight of this fixture. You can order “C” and “O”-clamps from any CHAUVET dealer or distributor (CLP-15, CLP-06 recommended).
Fixture Connection The fixture may be stacked together horizontally to create a strip light or vertically for a blinder effect. This can be used for runway lighting or cycloramas. With the different methods of bracket mounting, this turns this fixture into a very versatile lighting tool.
Lens Assembly Installation/Replacement The COLORdash™ Batten comes with 15 lens assembly pre-installed from the factory. However, there is 1 other optional lens kit (CL20X30) available as accessories, which will alter the beam angle. These each come in packages of 20pcs each. Therefore, if you have a fixture that has more than 20 LEDs (such as the COLORdash™ Batten), then be sure to take this into account.
Maximum recommended number of fixtures on a serial data link: 32 fixtures Data Cabling To link fixtures together you must obtain data cables. You can purchase CHAUVET-certified DMX cables directly from a dealer/distributor or construct your own cable. If you choose to create your own cable please use data-grade cables that can carry a high quality signal and are less prone to electromagnetic interference.
Note! If you use a controller with a 5 pin DMX output connector, you will need to use a 5 pin to 3 pin adapter. CHAUVET Model No: DMX5M, or DMX5F. The chart below details a proper cable conversion: IN TO...
4. O PERATING NSTRUCTIONS Control Options The COLORdash™ Batten is addressable in the DMX range of 001 to 512. In its simplest control form, this allows for the control of up to 56 fixtures in the 10-channel Stage1 personality; however, a secondary “ID”...
COLORcon™ Setup FIXTURE CONTROL PANEL SETUP Activate ID addressing in each fixture by setting panel function {ID ON/OFF} to ON. {MENU} {Settings) {ID ON/OFF} [ON] Set ID addresses in each fixture by setting panel function {ID address} to incremental values.
Setting the DMX address Each fixture requires a "start address" from 1 to 512. A fixture requiring one or more channels for control begins to read the data on the channel indicated by the start address. For example, a fixture that occupies or uses 7 channels of DMX and was addressed to start on DMX channel 100, would read data from channels: 100, 101, 102, 103, 104, 105 and 106.
Upload Customs The custom programs in the COLORdash™ Batten may be copied from one fixture to another, thus giving the ability to have to only program them on a single fixture, and then duplicate this on several others. This is accessed in the Control Panel as “Upload”. Follow the below steps for this process.
Menu Map UNCTION UNCTION ELECTION NSTRUCTION 000 ~ 255* User can combine Red, Green and Blue to (0 ~ 100%) Green generate a custom color 1. Static Color Select strobing frequency between 0 and Blue *Strobe range is 20Hz 0~20 Strobe Auto (1~10)
Page 19
COLORdash™ Batten User Manual 9/5/2008 9:49 AM...
DMX512 Channel Values The COLORdash™ Batten has 4 DMX512 channel configurations [STAGE1, BLOCK, ARC1, and ARC1+D]. STAGE 1 HANNEL ALUE UNCTION Dimmer 000 255 0 100% (or STEP TIME when CUS.01-10 is activated) 000 255 0 100% Green (or FADE TIME when CUS.01-10 is activated) 000 ...
Page 21
0 255 Auto Speed 9 (ID HANNEL ADDRESS SELECTION 000 009 All IDs ID 23 ID 46 010 019 ID 1 ID 24 ID 47 020 029 ID 2 ID 25 ID 48 030 039 ID 3 ID 26 ID 49...
Page 22
ARC 1 HANNEL ALUE UNCTION 000 255 0 100% Green 000 255 0 100% Blue 000 255 0 100% ARC 1 + D HANNEL ALUE UNCTION Dimmer 000 255 0 100% 000 255 0 ...
Important Notes about STAGE 1 DMX Operation MASTER DIMMER Channel 1 controls the intensity of the currently projected color When the slider is at the highest position (255), then the intensity of the output is at the maximum. RED, GREEN BLUE AND WHITE COLOR SELECTION Channels 2, 3 4 and 5 control the intensity ratio of each of the Red, Green, &...
5. COLOR ™ C ONTROLLER LCD Display Panel SOLD MODE SETUP DOWN SEPARATELY MODE Accesses main menu or backs out of sub-menu SETUP Selects the currently displayed menu or confirms the current function value Use to navigate upwards through menu items or increment function values DOWN Use to navigate downwards through menu...
Custom Program Select from the eight existing [Custom] programs and it will instantly play. Enter the [Edit] section to create or edit program. You can create or edit up to 100 scenes. To program less than 100 scenes, set the [Step time] of the scene after your last scene to 0.
[Reset to factory settings] This function will reset all the settings to the factory defaults except for [Custom] programs. Factory Default Settings Setting Default [Schedule] All times in schedule are reset to [00:00] [Wash program] Step times and fade times are reset to [001] [Effect program] Speeds are reset to [001] [DMX address]...
Support (Email): tech@chauvetlighting.com Telephone: (954) 929-1115 - (Press 4) Fax: (954) 929-5560 - (Attention: Service) Website: http://www.chauvetlighting.com Contact Us Wor l d Wi de General Information Chauvet Lighting 3000 North 29 Court Hollywood, FL 33020 voice: 954.929.1115 fax: 954.929.5560 toll free: 800.762.1084) World Wide Web www.chauvetlighting.com...
Connect fixtures using shielded two conductor twisted pair cable with three pin XLR male to female connectors. The shield connection is pin 1, while pin 2 is Data Negative (S-) and pin 3 is Data positive (S+). CHAUVET carries 3-pin XLR DMX compliant cables, DMX-10 (33’), DMX-4.5 (15’) and DMX-1.5 (5’) COLORdash™...
Package must be clearly labeled with a Return Merchandise Authorization Number (RA #). Products returned without an RMA # will be refused. Call CHAUVET and request RA # prior to shipping the fixture. Be prepared to provide the model number, serial number and a brief description of the cause for the return.
This fixture has built-in, automatic programs that may be triggered from the Stand alone operation onboard Control Panel If you still have a problem after trying the above solutions, please contact CHAUVET Technical Support at the location on page 28. COLORdash™ Batten User Manual...
Technical Specifications WEIGHT & DIMENSIONS Length ............................. 3.3 in (84 mm) Width ........................... 18.5 in (470 mm) Height............................ 7.5 in (191 mm) Weight ............................ 7.9 lbs (3.6 kg) POWER AC Power Auto-switching ..................100V~240V 50/60Hz AC Power Consumption ..................58W (0.8A) max at 120V 60Hz Power Consumption ..................